Rosslare AY-E20 Manuel utilisateur
AY-E20
Ultra-slim Vandal Resistant
Multi-format Proximity Reader
Instruction Manual
March 2008
Table of Contents
AY-E20 Instruction Manual Page ii
Table of Contents
1. General Information...........................................................3
1.1 Introduction.............................................................................. 3
1.2 Box Content............................................................................. 3
1.3 Ancillary Equipment................................................................ 3
2. Technical Specifications ...................................................4
2.1 Key Features............................................................................. 5
3. Installation...........................................................................6
3.1 Mounting the AY-E20 .............................................................. 6
4. Wiring Instructions ..............................................................8
4.1 Wiring the AY-E20..................................................................... 8
5. Operational Instructions ....................................................9
5.1 Testing the AY-E20 and Card Reading................................. 9
5.2 Card Transmission Format Selection ..................................... 9
5.3 Tri-Color LED Color Control................................................... 10
5.4 Buzzer Control ........................................................................ 10
5.5 Card Read/Hold Control...................................................... 10
5.6 Tamper Output...................................................................... 10
Appendix A. Limited Warranty ...........................................11
Appendix B. Technical Support .........................................13
General Information
AY-E20 Instruction ManualPage 3
1. General Information
1.1 Introduction
The AY-E20 is an ultra-slim, multi-format RFID proximity card reader
that is installed for use with access control systems. The unit is
vandal resistant and water resistant, suitable for indoor or outdoor
mounting.
This instruction manual contains information regarding the
features, mounting, wiring, operating instructions and warranty
details for the AY-E20 reader.
1.2 Box Content
Before beginning verify that all of the following is in the box. If
anything is missing, please report the discrepancy to your nearest
Rosslare office.
•One AY-E20 unit
•Installation kit and mounting template
•Installation and operating instruction
1.3 Ancillary Equipment
The following equipment is required to complete your installation:
•Compatible host controller (not supplied)- UL listed access
control unit, i.e., model AC-215U or AC-225U
Rosslare accessories can be found on www.rosslaresecurity.com.
Technical Specifications
AY-E20 Instruction Manual Page 4
2. Technical Specifications
Specifications AY-E20
Electrical Characteristics
Power supply type Linear type – recommended
Operating voltage
range 5 - 16VDC
Input current standby 40mA@12VDC
Max Input current 100mA@16VDC
Tamper output Open collector, active low, 16mA max
sink current
Cable distance to host
controller Up to 500ft (150 meters) using an 18AWG
cable
Proximity card read
range* 1.37inch (3.5cm )
Proximity card
modulation ASK at 125 KHz
Proximity card
compatibility EM cards
Card Transmit format 26-bit Wiegand, Clock & Data or Serial
RS232
LED indicators One tri-colored LED
Environmental Characteristics
Operating temp. range -25 to 145° F (-31 to 63° C)
Operating humidity 0 – 95% (non-condensing)
Outdoor usage Weather-resistant, meets IP-68, epoxy
Technical Specifications
AY-E20 Instruction ManualPage 5
Specifications AY-E20
potted, suitable for outdoor use
Mechanical
Size
(Height x Width x Depth) 155 x 45 x 8 mm
6.1x1.77x0.314 inch
Weight 135gr(0.297lb)
*Measured using Rosslare proximity card (AT-14) or equivalent. Range also
depends on electrical environment and proximity to metal.
2.1 Key Features
The key features for the AY-E20 are:
•Ultra-Slim Flush-mount design on flat surface
•Fully potted, waterproof construction for outdoor use
•Built-In 125 KHz ASK EM proximity card reader
•Selectable Card Transmission Formats: 26-Bit Wiegand,
Clock & Data, or Serial RS-232 output
•Optical back tamper sensor
•Bi-Color LED control
•Buzzer control
•Card read/hold control
•Mounting template for easier installation
•Installation kit
•Limited lifetime warranty
Installation
AY-E20 Instruction Manual Page 6
3. Installation
3.1 Mounting the AY-E20
Before starting, select the location to mount the AY-E20. This
location should be at shoulder height. To mount the AY-E20,
perform the following:
1) For wall mounting, use the included mounting template as a
guide for drilling holes and mounting screws (See figure 1).
2) Drill a hole for the cable. If mounting on metal, place a
grommet or electrical tape around the edge of the hole.
3) Route the interface cable from the AY-E20 to the Controller.
Figure 1 Drilling & Mounting Template
Installation
AY-E20 Instruction ManualPage 7
For US Gang Box mounting, no drilling is necessary. Simply screw
the AY-E20 to its mounting location or US gang box.
Note:
•A linear type power supply is recommended
•Card readers are to be used with control panels whose power
supply is UL Listed Class 2 or equivalent
Wiring Instructions
AY-E20 Instruction Manual Page 8
4. Wiring Instructions
4.1 Wiring the AY-E20
The unit is supplied with a 39.4 inch pigtail, having a 10-conductor
cable. To connect the unit to the controller, perform the following:
1) Prepare the unit's cable by cutting the cable jacket back 1¼
inches and strip the wire ½ inch.
2) Prepare the controller cable by cutting the cable jacket
back 1¼ inches and strip the wire ½ inch.
3) Splice the unit’s pigtail wires to the corresponding controller
wires and cover each connection. Refer to the wire color
table below.
Wire
Color Weigand
Output Mode Clock & Data
Output Mode
Serial (RS232)
Output Mode
Red +DC +DC +DC
Black Ground Ground Ground
Green Data 0 Data Tx (RS-232)
White Data 1 Clock -
Orange Green LED Green LED Green LED
Brown Red LED Red LED Red LED
Yellow Buzzer Buzzer Buzzer
Blue Hold Hold Hold
Purple Tamper Tamper Tamper
Grey Open Input Connect to GND
Connect to +DC
4) If the tamper output is used, connect the purple wire to the
correct input on the controller.
5) Trim and cover all unused conductors.
Operational Instructions
AY-E20 Instruction ManualPage 9
5. Operational Instructions
The AY-E20, once connected to standard access controller,
functions as a reader. This is indicated by one beep immediately
after power-on reset.
The following pages explain the operational instructions of the AY-
E20.
5.1 Testing the AY-E20 and Card Reading
The AY-E20 should be tested after wiring it to the Controller. To test
the AY-E20, perform the following:
1) Power-up the AY-E20. The LED and Beeper will activate one
time. This indicates that the AY-E20 is working properly.
2) Present the appropriate type of proximity card to the AY-E20.
The LED will momentarily flash green and a short beep will be
emitted. This indicates that the card was read properly by
the AY-E20.
3) Once the card’s data has been processed by the Controller,
the Controller can then switch the LED on the AY-E20 to
green. Refer to the relevant Controller instruction manual for
more information on controlling LED behavior via the
Controller.
5.2 Card Transmission Format Selection
To select the appropriate Card Transmission Format, perform one
of the following:
•26-Bit Wiegand - the grey wire should be an open circuit
•Clock & Data - the grey wire should be held to ground
•Serial RS-232 - the grey wire should be held to +DC (VIN).
Table des matières
Autres manuels Rosslare Système d'interphone
