ROSE DISPLAYS ANOKIOSK-STACKABLE Manuel utilisateur

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet

Note:

We recommended that two people

assemble this kiosk.

Step 1a

Slide spine into vertical rail.

Step 1b

Slide another vertical rail onto the

other edge of spine. Repeat for all

vertical rails and spines.

Step 2

Carefully insert corner brackets into

ends of bottom rails, using thumb as

shown in illustration. Two brackets

per end of each rail. Bracket can

bend if forced.

Detail- It is important that the corner

bracket tension tab faces toward

outside of frame. (2b)

Step 3

Lay out parts as they will be configured

on the floor.

Note: One kiosk will have Base Rail

other(s) will have stacker bar.

AnoKiosk™

Instructions for Assembly

Kiosk spine Corner brackets

Parts

Single rails Split rails

(Continued on other side)

2a 2b

1a 1b

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Bottom Rails

with Base Rail

3-Way

4-Way

Bottom Rails

with Stacker Bar

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet (side 2)

Instructions for Assembly continued

AnoKiosk™

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Step 4

Assemble the vertical rail assem-

blies onto the upward facing

corner brackets already inserted

into the bottom rails. All four

brackets should go into the

vertical rails at one time.

Note: (4 way only) The last

vertical rail will be tensioned.

This is normal.

Step 5

Insert corner brackets into ends

of split rails, 1 per end. Use thumb

as shown in illustration.

Step 6

Assemble split rails onto top ends

of vertical rails, one inside and

one outside of each side of the

AnoKiosk.

Step 7

Insert graphics into kiosk

with Base Rails.

Step 8

Place kiosk with stacker bar on

top of first kiosk. Line up stacker

bar with split rails on lower kiosk

and snap together.

Step 9

Load graphics into upper kiosk.

Step 10

If there are more kiosks to be

stacked repeat steps 8 and 9.

Figure 8 Figure 9

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet

Note:

We recommended that two people

assemble this kiosk.

Step 1a

Slide spine into vertical rail.

Step 1b

Slide another vertical rail onto the

other edge of spine. Repeat for all

vertical rails and spines.

Step 2

Carefully insert corner brackets into

ends of bottom rails, using thumb as

shown in illustration. Two brackets

per end of each rail. Bracket can

bend if forced.

Detail- It is important that the corner

bracket tension tab faces toward

outside of frame. (2b)

Step 3

Lay out parts as they will be configured

on the floor.

Note: One kiosk will have Base Rail

other(s) will have stacker bar.

AnoKiosk™

Instructions for Assembly

Kiosk spine Corner brackets

Parts

Single rails Split rails

(Continued on other side)

2a 2b

1a 1b

Bottom Rails

with Base Rail

3-Way

4-Way

Bottom Rails

with Stacker Bar

The AnoKiosk™ is a trademark of Rose Displays, Ltd. Neither the

manufacturer nor any sales agent may be held liable for injury, loss or

damage resulting from the use of these products. Part

#02INAnoKioskRigidStackable

Incept-09.20.02

Instruction Sheet (side 2)

Instructions for Assembly continued

AnoKiosk™

35 Congress Street, Salem, MA 01970

Tel# 1- 800 631-9707 Fax# 1-800-560-2890

e-mail:signware@rosedisplays.com

Step 4

Assemble the vertical rail assem-

blies onto the upward facing

corner brackets already inserted

into the bottom rails. All four

brackets should go into the

vertical rails at one time.

Note: (4 way only) The last

vertical rail will be tensioned.

This is normal.

Step 5

Insert corner brackets into ends

of split rails, 1 per end. Use thumb

as shown in illustration.

Step 6

Assemble split rails onto top ends

of vertical rails, one inside and

one outside of each side of the

AnoKiosk.

Step 7

Insert graphics into kiosk

with Base Rails.

Step 8

Place kiosk with stacker bar on

top of first kiosk. Line up stacker

bar with split rails on lower kiosk

and snap together.

Step 9

Load graphics into upper kiosk.

Step 10

If there are more kiosks to be

stacked repeat steps 8 and 9.

Figure 8 Figure 9

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ROSE DISPLAYS Accessoires

ROSE DISPLAYS

ROSE DISPLAYS SLIM HOLDER Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ECONOFRAME WITH CABLE CLIP AND BALL CHAIN Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS SUPERSNAP WITH BALL CHAIN Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ANOSKYBOX-TOP LOADING 3 WAY Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK ROUND WITH CABLE AND BALL Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS BUTTERFLY CLIPS WITH NON-LOCKING HOOKS Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS SPIDER RING WITH CABLE AND SAUCER Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS SNAIL ADHESIVE-GENERIC Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS SUPERSNAP WITH CABLE CLIP AND BALL CHAIN Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ANOMULTI SQUARE WITH CABLE CLIP AND BALL... Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS RAN-BAS-CC WITH CABLE AND SAUCER Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME VERSAMOUNT MAGNET BASE Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME VERSAMOUNT SCREW BASE SQ Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS RAN-BAS-CC SPIDER ANCHOR-GENERIC Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS CEILING SLUG Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS CLEVER WHATEVER Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ANOQUICK ROUND WITH CABLE AND SAUCER Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ANOMULTI ROUND WITH CABLE AND SAUCER Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ECONOFRAME WITH CABLE CLIP AND LOOP AND... Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME SQUARE WITH MULTICLIPS Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ECONOFRAME WITH SLATWALL HANGER Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ANOMULTI ROUND WITH MULTICLIPS Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS ANOFRAME SQUARE WITH NO HANGING Manuel utilisateur

ROSE DISPLAYS

ROSE DISPLAYS QUICKGRIP WITH MULTICLIPS Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur