Rockwell Automation Allen-Bradley ARMORSTART Manuel utilisateur

QUICK START

ARMORSTART®DISTRIBUTED

MOTOR CONTROLLER WITH

ARMORPOINT®BACKPLANE

Getting Started

BULLETIN 284A

Introduction This guide provides the basic information required to start up your

ArmorStart®Distributed Motor Controller. Factory default settings

and information regarding installing, programming, and ArmorPoint®

Communication Protocol, are described here. For detailed

information on specific product features or configurations, refer to the

ArmorStart user manual, Publication 284-UM001*-EN-P.

This guide is intended for qualified service personnel responsible for

setting up and servicing these devices. You must have previous

experience with and a basic understanding of electrical terminology,

configuration procedures, required equipment, and safety precautions.

For Bulletin 284A devices, you should understand Bulletin 1738

ArmorPoint adapter and I/O products.

Publication 284A-QS001C-EN-P - July 2006

Installation The ArmorStart Distributed Motor Controller is convection cooled.

Operating temperature must be kept between –20…40°C (–4…104°F).

Dimensions Dimensions are shown in millimeters (inches). Dimensions are not intended

to be used for manufacturing purposes. All dimensions are subject to

change.

Figure 1 Dimensions for 1 Hp and below @ 230V AC, 2 Hp and below @ 460V AC,

and 2 Hp and below @ 575V AC, IP67/NEMA Type 4 with

Conduit Entrance

Publication 284A-QS001C-EN-P - July 2006

Dimensions are shown in millimeters (inches). Dimensions are not intended

to be used for manufacturing purposes. All dimensions are subject to

change.

Figure 2 Dimensions for 2 Hp @ 230V AC, 3 Hp and above @ 460V AC, and 3 Hp and

above @ 575V AC, IP67/NEMA Type 4 with Conduit Entrance

Publication 284A-QS001C-EN-P - July 2006

Dimensions are shown in millimeters (inches). Dimensions are not intended

to be used for manufacturing purposes. All dimensions are subject to

change.

Figure 3 Dimensions for 1 Hp and below @ 230V AC, 2 Hp and below @ 460V AC,

and 2 Hp and below @ 575V AC, IP67/NEMA Type 4 with

ArmorConnect™ Connectivity

ArmorStart device with a 10 A short circuit protection rating

Publication 284A-QS001C-EN-P - July 2006

Dimensions are shown in millimeters (inches). Dimensions are not intended

to be used for manufacturing purposes. All dimensions are subject to

change.

Figure 4 Dimensions for 2 Hp @ 230V AC, 3 Hp and above @ 460V AC, and 3 Hp and

above @ 575V AC, IP67/NEMA Type 4 with ArmorConnect Connectivity

ArmorStart device with a 25 A short circuit protection rating

Publication 284A-QS001C-EN-P - July 2006

Wiring Power, Control, Safety Monitor Inputs, and Ground Wiring

Table 1 provides the power, control, safety monitor inputs, ground wire

capacity and the tightening torque requirements. The power, control,

ground, and safety monitor terminals will accept a maximum of two wires

per terminal.

Table 1 Power, Control, Safety Monitor Inputs, Ground Wire Size, and Torque

Specifications

Terminal Designations As shown in Figure 5, the ArmorStart Distributed Motor Controller contains

terminals for power, control, safety monitor inputs and ground wiring.

Access can be gained by removing the terminal access cover plate.

Figure 5 ArmorStart Power, Control, and Safety Monitor Terminals

Terminals Wire Size Torque Wire Strip Length

Power

and

Ground

Primary/Secondary

Terminal:

1.0…4.0 mm2

(#18 …#10 AWG)

Primary Terminal:

10.6…21.6 lb.-in.

(1.2…2.4 N•m)

Secondary Terminal:

5.3…7.3 lb.-in

(0.6…0.8 N•m)

0.35 in. (9 mm)

Control and Safety

Monitor Inputs 0.34mm2…4.0 mm2

(#22…#10 AWG)

5.0…5.6 lb.-in

(0.6 N•m) 0.35 in. (9 mm)

Primaries

Secondaries

Publication 284A-QS001C-EN-P - July 2006

Table 2 Power, Control, and Ground Terminal Designations

➊ Only available with the Safety Monitor option.

Terminal Designations No. of Poles Description

SM1 ➊2 Safety Monitor Input

SM2 ➊2 Safety Monitor Input

A1 (+) 2 Control Power Input

A2 (-) 2 Control Power Common

PE 2 Ground

1/L1 2 Line Power Phase A

3/L3 2 Line Power Phase B

5/L5 2 Line Power Phase C

Publication 284A-QS001C-EN-P - July 2006

ArmorConnect Power Media Description

The ArmorStart Power Media offers both three-phase and control power

cable system of cordsets, patchcords, receptacles, tees, reducers and

accessories to be utilized with the ArmorStart Distributed Motor Controller.

These cable system components allow quick connection of ArmorStart

Distributed Motor Controllers and reduce installation time. They provide

for repeatable, reliable connection of the three-phase and control power to

the ArmorStart Distributed Motor Controller and motor by providing a plug

and play environment that also avoids system mis-wiring. When specifying

power media for use with the ArmorStart Distributed Motor Controllers

(Bulletins 280, 281, 283, and 284) use only the Bulletin 280

ArmorConnect™ power media.

Figure 6 Three-Phase Power System Overview

➊Three-Phase Power Trunk- PatchCord cable with integral female or male connector on each end. (Example Part Number: 280-PWR35A-M*)

➋Three-Phase Drop Cable- PatchCord cable with integral female or male connector on each end. (Example Part Number: 280-PWR22A-M*)

➌Three-Phase Power Tees and Reducer -

Tee connects to a single drop line to trunk with quick change connectors – Part Number: 280-T35

Reducing Tee connects to a single drop line (Mini) to trunk (Quick change) connector – Part Number: 280-RT35

Reducer connects from quick change male connector to mini female connector– Part Number: 280-RA35

➍Three-Phase Power Receptacles -

Female receptacles are a panel mount connector with flying leads – Part Number: 280-M35F-M1

RESET

Bulletin 280/281

ArmorStart

ArmorPoint

Bulletin 284

ArmorStart

Ethernet

PLC

Bulletin 1492FB

Branch Circuit

Protective Device

Enclosure

Bulletin 1606 Bulletin 1606

Bulletin 800F

Emergency Stop

Pushbutton

Computer

Terminal

Publication 284A-QS001C-EN-P - July 2006

Figure 7 Control Power Media System Overview

➏Control Power Media Patchcords - PatchCord cable with integral female or male connector on each end

Example Part Number: 889N-F65GFNM-*

➐Control Power Tees - The E-stop In Tee (Part Number: 898N-653ES-NKF) is used to connect to the Bulletin 800F On-Machine E-Stop station using a

control power media patchcord. The E-stop Out tee (Part Number: 898N-653ST-NKF) is used with cordset or patchcord to connect to the ArmorStart

Distributed Motor Controller.

➑Control Power Receptacles - Female receptacles are a panel mount connector with flying leads –

Part Number: 888N-D65AF1-*

RESET

Bulletin 280/281

ArmorStart

ArmorPoint

Bulletin 284

ArmorStart

Ethernet

PLC

Bulletin 1492FB

Branch Circuit

Protective Device

Enclosure

Bulletin 1606 Bulletin 1606

Bulletin 800F

Emergency Stop

Pushbutton

Computer

Terminal

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Rockwell Automation Contrôleurs

Rockwell Automation

Rockwell Automation PowerFlex 40 Manuel utilisateur

Rockwell Automation

Rockwell Automation SMC Dialog Plus Manuel utilisateur

Rockwell Automation

Rockwell Automation Samsung NX70 Manuel utilisateur

Rockwell Automation

Rockwell Automation GV3000/SE 230 Manuel d'installation et d'exploitation

Rockwell Automation

Rockwell Automation ALLEN-BRADLEY SMC-3 Manuel utilisateur

Rockwell Automation

Rockwell Automation SLC 500 Thermocouple Manuel utilisateur

Rockwell Automation

Rockwell Automation Allen-Bradley 513 Manuel utilisateur

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex Series Manuel utilisateur

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OA16 Manuel utilisateur

Rockwell Automation

Rockwell Automation Allen-Bradley Logix5000 Manuel du propriétaire

Rockwell Automation

Rockwell Automation MicroLogix 1500 Manuel utilisateur

Rockwell Automation

Rockwell Automation Allen-Bradley 1769 CompactLogix Manuel utilisateur

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 7000 Manuel utilisateur

Rockwell Automation

Rockwell Automation Allen-Bradley PLC-2/30 Guide de configuration

Rockwell Automation

Rockwell Automation ics triplex AADvance Manuel

Rockwell Automation

Rockwell Automation micrologix 1200 Manuel utilisateur

Rockwell Automation

Rockwell Automation 1763-L16AWA Manuel utilisateur

Rockwell Automation

Rockwell Automation ARMORSTART 280D Manuel utilisateur

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-L72EROMS Manuel utilisateur

Rockwell Automation

Rockwell Automation 1763-L16AWA Manuel utilisateur

Rockwell Automation

Rockwell Automation Allen-Bradley 150-E Manuel utilisateur

Rockwell Automation

Rockwell Automation ARMORSTART Manuel du propriétaire

Rockwell Automation

Rockwell Automation Allen-Bradley 1512A Manuel utilisateur

Rockwell Automation

Rockwell Automation Allen-Bradley 856T-B24LC Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur

3M MicroTouch EX113 Manuel utilisateur