Rockwell Automation 1756-L1 Manuel utilisateur
Installation Instructions
ControlLogix Controller and Memory Board
Catalog Numbers 1756-L1, 1756-L1M1, 1756-L1M2,
1756-L1M3, 1756-L55, 1756-L55M12, 1756-L55M13,
1756-L55M14, 1756-L55M16, 1756-L55M22,
1756-L55M23, 1756-L55M24, 1756-L61, 1756-L62,
1756-L63, 1756-L64, 1756-L65, 1756-M1, 1756-M2,
1756-M3, 1756-M12, 1756-M13, 1756-M14,
1756-M16, 1756-M22, 1756-M23, 1756-M24,
1784-CF64, 1784-CF128
Topic Page
Important User Information 3
Explosion Hazards 4
Preventing Electrostatic Discharge 4
Removing Module While Under Power (RIUP) 4
Environment and Enclosure 5
North American Hazardous Location Approval 6
European Hazardous Location Approval 7
Before You Begin 8
Replace a Suspected Failed Controller 9
Resolving Common Errors 11
2ControlLogix Controller and Memory Board
Publication 1756-IN101L-EN-P - June 2008
Required System Components 12
Firmware Revisions 14
Preparing the Chassis 16
Remove the Controller from the Chassis 16
Installing a Memory Board on a ControlLogix5550 or ControlLogix5555 Controller 17
Installing a CompactFlash Card in a Controller 22
Connecting a Battery 25
Installing the Controller into the Chassis 28
Check the BAT Status Indicator 29
Checking the OK Status Indicator 30
Update the Controller 32
Connecting a Serial Cable 34
Interpreting the Status Indicators 36
Clear a Major Fault 38
Clear a Nonrecoverable Fault 39
Choosing the Operating Mode of the Controllers 40
Specifications 41
Topic Page
ControlLogix Controller and Memory Board 3
Publication 1756-IN101L-EN-P - June 2008
Important User Information
Solid state equipment has operational characteristics differing from those of electromechanical
equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls
(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at
http://literature.rockwellautomation.com) describes some important differences between solid state
equipment and hard-wired electromechanical devices. Because of this difference, and also because of
the wide variety of uses for solid state equipment, all persons responsible for applying this equipment
must satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the
many variables and requirements associated with any particular installation, Rockwell Automation, Inc.
cannot assume responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell
Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING Identifies information about practices or circumstances that can cause an explosion in
a hazardous environment, which may lead to personal injury or death, property
damage, or economic loss.
IMPORTANT Identifies information that is critical for successful application and understanding of
the product.
ATTENTION Identifies information about practices or circumstances that can lead to personal
injury or death, property damage, or economic loss. Attentions help you identify a
hazard, avoid a hazard and recognize the consequences.
Labels may be on or inside the equipment (for example, a drive or motor) to alert
people that dangerous voltage may be present.
Labels may be on or inside the equipment (for example, a drive or motor) to alert
people that surfaces may reach dangerous temperatures.
SHOCK HAZARD
BURN HAZARD
4ControlLogix Controller and Memory Board
Publication 1756-IN101L-EN-P - June 2008
Explosion Hazards
Preventing Electrostatic Discharge
Removing Module While Under Power (RIUP)
WARNING An electrical arc can occur if you:
xinsert or remove the CompactFlash card.
xinsert or remove the controller while backplane power is on.
xconnect or disconnect the battery.
xconnect or disconnect the serial cable with power applied to this module
or the serial device on the other end of the cable.
This could cause an explosion in hazardous location installations. Make sure
that power is removed or the area is nonhazardous before proceeding
ATTENTION This equipment is sensitive to electrostatic discharge, which can cause
internal damage and affect normal operation. Follow these guidelines when
you handle this equipment.
xTouch a grounded object to discharge potential static.
xWear an approved grounding wriststrap.
xDo not touch connectors or pins on component boards.
xDo not touch circuit components inside the equipment.
xUse a static-safe workstation, if available.
xStore the equipment in appropriate static-safe packaging when not in
use.
WARNING When you insert or remove the module while backplane power is on, an
electrical arc can occur. This could cause an explosion in hazardous location
installations.
Be sure that power is removed or the area is nonhazardous before
proceeding. Repeated electrical arcing causes excessive wear to contacts on
both the module and its mating connector. Worn contacts may create
electrical resistance that can affect module operation.
ControlLogix Controller and Memory Board 5
Publication 1756-IN101L-EN-P - June 2008
Environment and Enclosure
ATTENTION This equipment is intended for use in a Pollution Degree 2 industrial
environment, in overvoltage Category II applications (as defined in IEC
publication 60664-1), at altitudes up to 2000 m (6561 ft) without
derating.
This equipment is considered Group 1, Class A industrial equipment
according to IEC/CISPR Publication 11. Without appropriate
precautions, there may be potential difficulties ensuring
electromagnetic compatibility in other environments due to
conducted as well as radiated disturbance.
This equipment is supplied as open-type equipment. It must be
mounted within an enclosure that is suitably designed for those
specific environmental conditions that will be present and
appropriately designed to prevent personal injury resulting from
accessibility to live parts. The enclosure must have suitable
flame-retardant properties to prevent or minimize the spread of flame,
complying with a flame spread rating of 5VA, V2, V1, V0 (or
equivalent) if non-metallic. The interior of the enclosure must be
accessible only by the use of a tool. Subsequent sections of this
publication may contain additional information regarding specific
enclosure type ratings that are required to comply with certain
product safety certifications.
In addition to this publication, see:
xIndustrial Automation Wiring and Grounding Guidelines, for additional
installation requirements, Allen-Bradley publication 1770-4.1.
xNEMA Standards publication 250 and IEC publication 60529, as
applicable, for explanations of the degrees of protection provided by
different types of enclosure.
6ControlLogix Controller and Memory Board
Publication 1756-IN101L-EN-P - June 2008
North American Hazardous Location Approval
The following information applies when
operating this equipment in hazardous
locations.
Informations sur l’utilisation de cet
équipement en environnements dangereux.
Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for
use in Class I Division 2 Groups A, B, C, D, Hazardous
Locations and nonhazardous locations only. Each product is
supplied with markings on the rating nameplate indicating
the hazardous location temperature code. When
combining products within a system, the most adverse
temperature code (lowest "T" number) may be used to help
determine the overall temperature code of the system.
Combinations of equipment in your system are subject to
investigation by the local Authority Having Jurisdiction at
the time of installation.
Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne
conviennent qu'à une utilisation en environnements de
Classe I Division 2 Groupes A, B, C, D dangereux et non
dangereux. Chaque produit est livré avec des marquages sur
sa plaque d'identification qui indiquent le code de
température pour les environnements dangereux. Lorsque
plusieurs produits sont combinés dans un système, le code de
température le plus défavorable (code de température le plus
faible) peut être utilisé pour déterminer le code de
température global du système. Les combinaisons
d'équipements dans le système sont sujettes à inspection par
les autorités locales qualifiées au moment de l'installation.
WARNING EXPLOSION HAZARD -
• Do not disconnect equipment unless
power has been removed or the
area is known to be nonhazardous.
• Do not disconnect connections to
this equipment unless power has
been removed or the area is known
to be nonhazardous. Secure any
external connections that mate to
this equipment by using screws,
sliding latches, threaded
connectors, or other means
provided with this product.
• Substitution of components may
impair suitability for Class I,
Division 2.
• If this product contains batteries,
they must only be changed in an
area known to be nonhazardous.
AVERTISSEMENT RISQUE D’EXPLOSION –
• Couper le courant ou s'assurer
que l'environnement est classé
non dangereux avant de
débrancher l'équipement.
• Couper le courant ou s'assurer
que l'environnement est classé
non dangereux avant de
débrancher les connecteurs. Fixer
tous les connecteurs externes
reliés à cet équipement à l'aide
de vis, loquets coulissants,
connecteurs filetés ou autres
moyens fournis avec ce produit.
• La substitution de composants
peut rendre cet équipement
inadapté à une utilisation en
environnement de Classe I,
Division 2.
• S'assurer que l'environnement est
classé non dangereux avant de
changer les piles.
ControlLogix Controller and Memory Board 7
Publication 1756-IN101L-EN-P - June 2008
European Hazardous Location Approval
European Zone 2 Certification (The following applies when the product bears the
Ex or EEx Marking)
This equipment is intended for use in potentially explosive atmospheres as defined by
European Union Directive 94/9/EC.
The LCIE (Laboratoire Central des Industries Electriques) certifies that this equipment has
been found to comply with the Essential Health and Safety Requirements relating to the
design and construction of Category 3 equipment intended for use in potentially explosive
atmospheres, given in Annex II to this Directive.
Compliance with the Essential Health and Safety Requirements has been assured by
compliance with EN 60079-15.
ATTENTION This equipment is not resistant to sunlight or other sources of UV radiation.
WARNING xThis equipment must be used only with ATEX certified backplanes.
xSecure any external connections that mate to this equipment by using
screws, sliding latches, threaded connectors, or other means provided with
this product.
xDo not disconnect equipment unless power has been removed or the area is
known to be nonhazardous.
xEquipment must be installed in an enclosure providing at least IP54
protection when applied in Class I, Zone 2 environments.
xThis equipment shall be used within its specified ratings defined by
Allen-Bradley.
8ControlLogix Controller and Memory Board
Publication 1756-IN101L-EN-P - June 2008
Before You Begin
Read this section for important information about using these products,
noting that this publication covers the products shown in the table.
Product Cat. No. Series
ControlLogix5550 controller 1756-L1, 1756-L1M1, 1756-L1M2, 1756-L1M3 A
ControlLogix5555 controller 1756-L55, 1756-L55M12, 1756-L55M13,
1756-L55M14, 1756-L55M16, 1756-L55M22,
1756-L55M23, 1756-L55M24
A
ControlLogix5561 controller 1756-L61 A, B
ControlLogix5562 controller 1756-L62 A, B
ControlLogix5563 controller 1756-L63 A, B
ControllLogix5564 controller 1756-L64 B
ControlLogix5565 controller 1756-L65 B
ControlLogix5550 memory
board
1756-M1, 1756-M2, 1756-M3 A
ControlLogix5555 memory
board
1756-M12, 1756-M13, 1756-M14, 1756-M16,
1756-M22, 1756-M23, 1756-M24
A
Industrial CompactFlash
card
1784-CF64, 1784-CF128 A
ControlLogix Controller and Memory Board 9
Publication 1756-IN101L-EN-P - June 2008
Replace a Suspected Failed Controller
To replace a failed controller, do the following.
1. Cycle power to the chassis.
2. Make sure the OK status indicator is
solid red, noting that if the OK status
indicator is not solid red, the controller
does not require replacement.
3. Match the catalog numbers of the
controllers and memory boards, noting
that 1756-Mxxx is the catalog number of
the memory board, if one is installed, and
1756-Lxxx is the catalog number of the
controller, as shown in the figure.
ControlLogix
1756-M…
CAT. NO./SERIES
ControlLogix
1756-L…
CAT. NO./SERIES
1756-M...
1756-L...
10 ControlLogix Controller and Memory Board
Publication 1756-IN101L-EN-P - June 2008
4. Insert the battery.
5. Insert the key, and turn it to the PROG position.
6. Insert the controller into the chassis.
7. Use ControlFlash software to update the firmware of the controller.
8. Download the RSLogix 5000 project to the controller.
RS232
BATTERY
PORT
1-DCD
2-RXD
4-DTR
3-TXD
5-GND
DSR-6
CTS-8
RTS-7
N/C-9
1
2
BATTERY
DATE
UP
COMPACT
FLASH
2
To
Insert 1
To Eject
1 + 2
2
1
1
42523
Series A Series B
20880
Ce manuel convient aux modèles suivants
28
Table des matières
Autres manuels Rockwell Automation Contrôleurs
Rockwell Automation
Rockwell Automation SMC Dialog Plus Manuel utilisateur
Rockwell Automation
Rockwell Automation Allen-Bradley Guardmaster 440G-MZ Manuel utilisateur
Rockwell Automation
Rockwell Automation Allen-Bradley GuardLogix 5570 Manuel utilisateur
Rockwell Automation
Rockwell Automation PowerFlex 40 Manuel utilisateur
Rockwell Automation
Rockwell Automation Allen-Bradley OneGear Manuel utilisateur
Rockwell Automation
Rockwell Automation Allen-Bradley PowerFlex 23PFC Manuel utilisateur
Rockwell Automation
Rockwell Automation MicroLogix 1000 Manuel utilisateur
Rockwell Automation
Rockwell Automation PowerFlex 700 Manuel utilisateur
Rockwell Automation
Rockwell Automation Allen-Bradley Logix5000 Manuel du propriétaire
Rockwell Automation
Rockwell Automation Allen-Bradley 513 Manuel utilisateur
Rockwell Automation
Rockwell Automation PowerFlex 700S Manuel utilisateur
Rockwell Automation
Rockwell Automation Allen-Bradley Logix 5000 Series Manuel du propriétaire
Rockwell Automation
Rockwell Automation Allen-Bradley 1756-L72EROMS Manuel utilisateur
Rockwell Automation
Rockwell Automation Allen-Bradley 1769 CompactLogix Manuel utilisateur
Rockwell Automation
Rockwell Automation ArmorStart Bulletin 280G Manuel utilisateur
Rockwell Automation
Rockwell Automation 1763-L16AWA Manuel utilisateur
Rockwell Automation
Rockwell Automation 1336 PLUS Manuel utilisateur
Rockwell Automation
Rockwell Automation Allen-Bradley Logix 5000 Series Manuel du propriétaire
Rockwell Automation
Rockwell Automation Allen-Bradley 1502 Manuel utilisateur
Rockwell Automation
Rockwell Automation 1763-L16AWA Manuel utilisateur
Rockwell Automation
Rockwell Automation Allen-Bradley SMC-Flex 150 Manuel utilisateur
Rockwell Automation
Rockwell Automation Allen-Bradley Logix 5000 Series Manuel du propriétaire
Rockwell Automation
Rockwell Automation PowerFlex 700S Manuel utilisateur
Rockwell Automation
Rockwell Automation CompactLogix series Manuel utilisateur
