Rockler JIG IT 50713 Manuel utilisateur

JIG IT®Undermount

Drilling Guide Instructions

Before attempting to install the locking devices, make

sure that the dimensions of your drawer box meet the

specifications in the instructions that came with your

Blum Tandem Drawer Slides. Also, as specified in the

instructions, cut notches in the back of the drawer box, at

the bottom, to accommodate the slides. Try to make the

notches as flush to the drawer bottom and square to the

sides as possible.

Set Depth Collars on Drill Bits

1. Slide the smaller depth collar on the 2.5mm drill bit and

insert the bit in the 2.5mm depth guide in the rounded

foot of the Drill Guide.

2. Allow the bit to bottom out in the hole and the stop

collar to rest on the Drill Guide. Secure the depth collar

by tightening the set screw with the included hex

wrench. Fig. 1.

3. Repeat Steps 1 and 2 for the 6mm bit, using the 6mm

depth guide in the Drill Guide. Fig. 1

Angled guide holes

for locking devices

Stop collar

depth guides

Pin guide holes

6mm drill bit

and stop collar

Hex wrench

2.5mm drill bits

with stop collar

2Distributed by Rockler Companies, Inc.

50713

Rev 10/15

Fig. 2

Fig. 3

Drill for the Locking Devices

1. With the drawer box upside down on a stable work

surface, position the Drilling Guide on the drawer

bottom in one of the front corners. Make sure the flat

foot is against the drawer side and the arrow points

to the side.

2. With the 2.5mm bit chucked in a handheld drill, hold

the Drill Guide in place and use the guide holes to drill

the angled holes for mounting the slide bracket. Fig. 2.

3. Flip the Drill Guide side-to-side and repeat Steps 1

and 2 in the other front bottom corner of the

drawer box.

Drill for the Slides’ Rear Pins

1. With the drawer box still upside down, place the Drill

Guide in one of the notches and against the drawer side.

Make sure the shoulder on the rounded foot of the

guide rests squarely on the bottom of the notch.

2. With the 6mm bit chucked in a handheld drill, hold the

Drill Guide in place and use the guide hole closest to

the drawer side to bore the hole for the rear pin

on the slide. Fig. 3.

3. Reposition the Drill Guide in the other notch and

repeat Steps 1 and 2, using the other guide hole in

the Drill Guide.

Check Rockler.com for updates. If you have further questions, please

contact our Technical Support Department at 1-800-260-9663

or support@rockler.com

Locking device

Table des matières

Autres manuels Rockler Outils

Rockler

Rockler 63779 Manuel utilisateur

Rockler

Rockler Interlock Signmaker's Script Font Template Manuel utilisateur

Rockler

Rockler 22818 Manuel utilisateur

Rockler

Rockler 55512 Manuel utilisateur

Rockler

Rockler Interlock Signmaker’s Templates State Park Manuel utilisateur

Rockler

Rockler 45968 Mode d'emploi

Rockler

Rockler 55391 Manuel utilisateur

Rockler

Rockler 37375 Manuel utilisateur

Rockler

Rockler 56372 Manuel utilisateur

Rockler

Rockler 52149 Manuel utilisateur

Rockler

Rockler 68547 Manuel utilisateur

Rockler

Rockler 53651 Manuel utilisateur

Rockler

Rockler Trim Router Table Manuel utilisateur

Rockler

Rockler JIG IT Manuel utilisateur

Rockler

Rockler Beadlock Pro Manuel utilisateur

Rockler

Rockler Miter-Tight Picture Frame Clamp Manuel utilisateur

Rockler

Rockler 43450 Mode d'emploi

Rockler

Rockler 36833 Manuel utilisateur

Rockler

Rockler ProFence 47905 Manuel utilisateur

Rockler

Rockler 57484 Manuel utilisateur

Rockler

Rockler 22.5 Miter Sled Manuel utilisateur

Rockler

Rockler 52149 Manuel utilisateur

Rockler

Rockler JIG IT Manuel utilisateur

Rockler

Rockler Dust RIGHT Manuel utilisateur

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser