Rockler Power Tool Mobile Base Manuel utilisateur

Congratulations on your purchase of the Power Tool Mobile Base! Follow these simple assembly instructions

and you’ll be moving your large power tools around easily in no time.

Please read these instructions completely before starting to assemble your Power Tool Mobile Base.

Familiarity with the process will make the steps easier to understand. Please follow all steps carefully.

Power Tool Mobile

Base Instructions

PARTS list Quantity

Quantity

1 CornerBracket 4

2 CasterAssembly 1

3 Wheel 2

4 FootLever 1

5 PivotBracket 1

6 LevelingLegs 2

7 5/16"-18x4"HexHeadScrew 1

8 5/16"-18x21⁄4"HexHeadScrew 2

9 1/2"x4"Pin 1

10 5/16"FlatWasher 4

11 5/16"-18HexNut 20

12 5/16"-18LockNut 3

13 5/16"-18x2"CarriageHeadScrew 16

14 1/2"FlatWasher 4

15 RetainingRing 2

16 5/16"-18x2"ThumbScrew 2

Fig.1

BaseAssembly

1. PlacetheWheels(3)intotwoCornerBrackets(1)

 andsecureusingthe21⁄4"HexHeadScrew(8)from

 insidetheCornerBracket(1)andsecurewiththe

 5/16"-18LockNut(12).Fig.1.

 Note:WhentheCornerBrackets(1)areat90°

 anglesfromeachothertheWheels(3)shouldpoint

 inthesamedirection.

2. DeterminebestplacementofFootLever(4)and

 wheels,keepinginmindthattheFootLever(4)

 mustbeattachedoppositethewheels.

 Note:FootLever(4)locationmustnotinterferewith

 themachineorcausethemachinetobetop-heavy

 whenintheraisedposition.

3. Measurethefootprintofthemachineandadd

 1/2"tothewidthandlengthforthewood

 framedimensions.

4. Cuttwopiecesof11⁄2"x11⁄2"hardwoodfor

 eachmeasurementtomaketheframe(Total

 of4pieces).

5. Feedthecutpiecesthroughthemetalframeand

 alignthemsotheyareflushwiththecornersFig.2.

6. MarkplacementofholesintheCornerBrackets(1)

 onthewoodenpieces.

7. PositionthePivotBracket(5)halfwayonthefoot

 levelerboardandmarkholelocations.Fig.3.

8. Lookingdownfromaboveatfrontcorner,measure

 3/4"fromtheoutercornerineachdirectionand

 drawintersectingperpendicularlinestomarkthe

 placementofthelevelinglegs.Fig.4.

9. Carefullydrillthe7/16"diameterholesonalltwenty

 locationsdetailedintheprevioussteps.

10. ReassemblethebaseandattachtheCorner

 Brackets(1)usingthe5/16"-18x2"Carriage

 Bolts(13)and5/16"-18HexNuts(11).Fig.5.

 Note:Insertthe5/16"-18x2"CarriageBolts(13)

 fromtheinsideoftheCornerBrackets(1).

Fig.2

Fig.3

Fig.4

Fig.5

831

92051

Rev03/13

Distributed by Rockler Companies, Inc.

AttachingtheLevelingScrews

1. Attachone5/16"-18HexNut(11)and5/16"Flat

 Washer(10)totheLevelingLeg(6).Fig.6.

2. InsertLevelingLeg(6)intothesideboardandfasten

 itinplacewithanother5/16"FlatWasher(10)and

 5/16"-18HexNut(11).Fig.7.

3. RepeatwithotherLevelingLeg(6).

AttachingtheCasterAssembly

1. AttachtheCasterAssembly(2)witha5/16"-18x4"

 HexHeadScrew(7)and5/16"-18LockNut(12)to

 thePivotBracket(5).Fig.8.

2. AttachtheFootLever(4)tothePivotBracket(5)with

 the1/2"x4"Pin(9)andfour1/2"FlatWashers(14)

 andtwoRetainingRings(15).Fig.9.

 Note:The1/2"FlatWashers(14)shouldbebetween

 theFootLever(4)andthePivotBracket(5).

3. PositionandattachthePivotBracket(5)totheboard

 withtwo5/16"-18x2"ThumbScrews(16).Fig.10.

4. Adjustthelevelinglegsbyraisingthemobilebase

 andlooseningortighteningthehexnutssothe

 baseislevel.

Attention Rockler Plan User

Before starting, please read the plan completely. Check Rockler.com

for updates that may not be included on this copy. If you have further

questions, please contact our Technical Support Department,

1-800-260-9663 or support@rockler.com

Fig.6 Fig.7

Fig.9

Fig.8

Fig.10

1414

Autres manuels Rockler Accessoires pour outils électriques

Rockler

Rockler XL Router Table Box Joint Jig Manuel utilisateur

Rockler

Rockler 52885 Manuel utilisateur

Rockler

Rockler Trim Router Table Manuel utilisateur

Rockler

Rockler Router Table XL Box Joint Jig Manuel utilisateur

Rockler

Rockler Router Table Spline Jig Manuel utilisateur

Rockler

Rockler 59032 Manuel utilisateur

Rockler

Rockler 57510 Manuel utilisateur

Rockler

Rockler Pro Lift Manuel utilisateur

Rockler

Rockler 3/8 Tenon Router Bit Manuel utilisateur

Rockler

Rockler 57896 Manuel utilisateur

Rockler

Rockler 27712 Manuel utilisateur

Rockler

Rockler ProFence 47905 Manuel utilisateur

Rockler

Rockler 22796 Manuel utilisateur

Rockler

Rockler Dust RIGHT Manuel utilisateur

Manuels Accessoires pour outils électriques populaires d'autres marques

Bosch

Bosch OSC004 Manuel utilisateur

Bosch

Bosch RA1054 Instructions de montage

Grizzly

Grizzly T10808 Manuel utilisateur

Kitagawa

Kitagawa SC N Series Manuel utilisateur

Wolfcraft

Wolfcraft FKS 145 Guide rapide

ADAMAS

ADAMAS B32 Manuel utilisateur

STEINEL PROFESSIONAL

STEINEL PROFESSIONAL 4007841009595 Manuel utilisateur

Echo

Echo Speed-Feed Universal 400 LH/RH Manuel utilisateur

SCHUNK

SCHUNK ROTA TB-TBS-EP Instructions d'utilisation

Schmid

Schmid RAPID Secure XL Manuel utilisateur

Drill Master

Drill Master 360X Manuel utilisateur

Toro

Toro 138-5050 Manuel utilisateur

jbc

jbc SF-SD Manuel utilisateur

Bosch

Bosch GTA 3800 Professional Instructions de montage

RG AVAK

RG AVAK MaxDrill Series Manuel utilisateur

infaco

infaco PW3 Manuel utilisateur

Gloria

Gloria CUT & BRUSH Manuel utilisateur

Bench Dogs

Bench Dogs Quad MFT Hinge System Manuel utilisateur