Robinson Willey RIVIERA Note de version

Installation & Servicing Instructions

PLEASE LEAVE THESE INSTRUCTIONS WITH THE USER

The Data Badge and Serial Number are located on the left hand side of the base panel.

Cat II G20 at 20mbar convertible to G31 at 37mbar.

2H3P For use in GB and IE.

BELVEDERE

AND

RIVIERA G C No. 32-170-23

G C No. 32-170-24

This product uses fuel effect pieces containing Refractory Ceramic Fibre (RCF), which are man-made

vitreoussilicatefibres. Excessiveexposuretothesematerialsmaycausetemporaryirritationtoeyes,

skin and respiratory tract, consequently, it makes sense to take care when handling these articles to

ensurethatthereleaseofdustiskeptto a minimum.

To ensure that the release of fibres from these RCF articles is kept to a minimum, during installation

and servicing we recommend cleaning should be carried out in a well-ventilated area or in the

open air, by gently brushing with the pieces held away from your face so that you avoid

inhaling the dust. We do not recommend the use of a normal domestic vacuum cleaner,

which may blow dust back into the air. If a vacuum cleaner is recommended for use by your

organisation, you must use a HEPAfiltered vacuum to remove any dust and soot accumulated in and

around the fire before and after working on the fire. When replacing these articles we recommend that

the replaced items are not broken up, but are sealed within heavy duty polythene bags, clearly

labelled as RCF waste. This is not classified as "hazardous waste" and may be disposed of at a tipping

site licensed for the disposal of industrial waste. Protective clothing is not required when handling the

articles, but we recommend you follow the normal hygiene rules of not smoking, eating or drinking in

thework area and always wash yourhands before eating or drinking.

Advise the customer that they should read their Users instructions before operating the fire and

alwaysfollow the advice in the Sectionheaded"Cleaning your Fire".

2 2

INTRODUCTION AND GENERAL INSTALLATION

REQUIREMENTS

TECHNICAL DATA

AVAILABLE FENDERS

AVAILABLE TRIMS

CONTENTS OF SCREW PACK

CONTENTS OF COAL PACK

CONDITIONS OF INSTALLATION

SITING GENERAL

FLUES AND CHIMNEYS

Brick Chimney, 178mm diameter (7 inch)

Stone or Lined Flue and 125mm diameter (5 inch) Flue

Pre-Cast Flue

Rebated Surround Installation

Metal Fluebox 125mm diameter (5 inch) Flues

SHELF HEIGHT AND SIDE CLEARANCES

Combustible Shelf

Non-Combustible Shelf

INSTALLATION OF FIRE

UNPACKING

PREPARATION OF FIRE

Spigot Restrictor

Fender Mask

Burner Tray

METHODS OF INSTALLATION

Fixing by Tension Cable

Fixing Directly to Surround Face

GAS CONNECTION

Concealed Connection

TEST FOR GAS SOUNDNESS

COMMISSIONING

INSTALLFUEL EFFECT COMPONENTS including

FIT TRIM AND FENDER

CHECK GAS PRESSURE

TEST FOR SPILLAGE

CHECK IGNITION

CHECK OPERATION OF FSD

INSTRUCT USER

SERVICING INSTRUCTIONS

REMOVE BURNER TRAY

MAIN BURNER INJECTOR

GAS TAPASSEMBLY

PILOT ASSEMBLY

FUEL EFFECT COMPONENTS

MAIN BURNER

CONTROL KNOB

HINTS ON FAULT FINDING

NOTEPAD

SHORT LIST OF PARTS

PAGE

CONTENTS

SECTION

1.0

2.0

2.1

3.0

4.0

5.0

5.1

5.2

5.2.1

5.2.2

5.2.3

5.2.4

5.3

5.3.1

5.3.2

6.0

6.1

6.2

6.2.1

6.2.2

6.2.3

6.3

6.3.1

6.3.2

6.4

6.4.1

6.5

7.0

7.1

7.2

7.3

7.4

7.5

8.0

9.0

9.1

9.2

9.3

9.4

9.5

9.6

9.7

10.0

11.0

12.0

3 3

1.1 DIMENSIONS

(Overall) mm

Height 595

Width 500

Depth 105

ForwardProjection 90

Heightto topof flueaperture 510

Weight 16Kg

1.2 INPUTSANDPRESSURES

NaturalGas Propane Gas

MaximumHeat Input 6.2kW 21,154 Btu/h 5.8kW 19,789 Btu/h

MaximumHeat Output 3.8kW 12,956 Btu/h 3.6kW 12,283 Btu/h

MinimumHeat Input 2.0kW 6,824 Btu/h 3.5kW 11,942 Btu/h

EfficiencyClass II II

SupplyPressure 20.0mbar 8.0 inwg 37.0mbar 14.8 inwg

SettingPressure 12.2mbar ±1 mbar 4.9± 0.4in wg 34.0 mbar± 1mbar 13.6± 0.4in wg

GasRate Adjustment NONE NONE

1.3 BURNERAND CONTROLDETAILS

MainBurner 989559 989559

PilotBurner SIT OPNG9077 SITOP LPG9255

Injector(Main Burner) BrayCat 16/460 Bray Cat10/180

Ignition ControlIntegrated PiezoSpark Ignition

ControlTap Concentric(with FSD)Model NumberTESA 2377

SparkGap 3.0mm to5.0mm

ControlKnob Settings OFF,PILOT/IGNITION, HIGH,MED, LOW,ECON

GENERAL INSTALLATION REQUIREMENTS

NOCOMPONENT OFTHIS FIREIS MANUFACTUREDFROMASBESTOSOR ASBESTOSRELATEDPRODUCTS.

THE BELVEDERE AND RIVIERA are a range of open fronted inset live coal effect gas fires specially designed for Pre-Cast Flue

application and are also suitable for use with Brick Chimneys, twin walled or insulated Metal/Pre-fabricated Flues of 125mm minimum

diameter and Flueboxes conforming to the constructional requirements of BS 715. They are fitted with a combined flame supervision

and oxygen depletion monitoring device. The fire is for hearth mounting only on a non-combustible hearth. If required the fire can be

fitted using a rebated surround if it is to be installed in a pre-cast flue (optional extras are required). The fire is ready for use on Natural

Gasand isconvertible foruse onPropane Gas(LPG) usingkit partnumber 989551.

In your own interest and that of safety, it is the law that all gas appliances are installed by competent persons in accordance with the

currentGas Safety(Installation andUse) Regulations.Failure toinstall appliancescorrectlycouldleadtoprosecution.

The installation MUST be in accordance with these installation instructions, all the relevant parts of the Local and National Building

Regulations or Building Standards (Scotland) (Consolidation) Regulations and the relevant recommendations of the current editions of

thefollowing BritishStandards:

B.S.5871: Part2

B.S.5440: Parts1and 2

B.S.6891

B.S.6461: Parts1and 2

B.S.715

B.S.1251

B.S.1289

B.S.1289: Part1

B.S.1289: Part2

Anyother relevantBritish StandardCode ofPractice and/orLocal BuildingRegulations andin accordancewith therules inforce.

INTRODUCTION

1.0 TECHNICAL DATA

4 4

2.0 AVAILABLE FENDERS

5 5

BELVEDERE FENDER AND ASHPAN

RIVIERA FENDER AND ASHPAN

Both the above are available in black/brass or black/chrome effect

6 6

2.1 AVAILABLE TRIMS

BELVEDERE TRIM

RIVIERA TRIM

Available in Black with

Brass or Chrome effect insert

Available in

Brass or Chrome effect

3.0 CONTENTS OF SCREW PACK

4.0 CONTENTS OF COAL PACK

The contents of the screw pack are as follows

(refer to Fig 1.): -

Key Qty Description

A 2 Fixing Cables

B 2 Cable Adaptors

C 2 Grub Screws

D 4 Cable Eyelets

E 4 Wall Plugs

F 4 Fire Fixing Screws

G 4 No 6 Self Tapping Screws

H 1 Restrictor

I 1 Gas Inlet Grommet

J 2 Cable Tensioning Bolts

The contents of the coal pack are as follows

(refer to Fig 2.): -

Key Qty Description

A 1 Base Coal Matrix

B 1 Rear Coal

C 1 Left Hand Side Cheek

D 1 Right Hand Side Cheek

E 7 Rectangular Coals

Fig 2.

Fig 1.

7 7

5.1 SITINGGENERAL

This fire is suitable for hearth mounting only on a non-combustible hearth at least 13mm thick and measuring at least 630mm wide by

330mm deep, the periphery of which should preferably be 50mm above the floor level in order to discourage the placing of carpets or

rugs over it. It MUST NOT be fitted directly on a combustible wall. The fire should be installed so that no part of a combustible wall i.e. not

part of the fire surround but a full wall at 90 to the fire is less than 500mm from the radiant source. If this is not possible the combustible

sidewall mustbe suitablyprotected.

FIREPLACEOPENING

The front opening of the fireplace must be between 406mm and 457mm wide and between 550mm and 572mm high (see Section 5.2). If

the opening is greater it must be bricked up until the opening is a maximum of 572mm high and 457mm wide, alternatively a non-

combustibleinfill panelmay beused toachieve therequired dimensions.

DONOT USETHE BACKOF AFIRE SURROUNDOR MARBLETOACHIEVE THEABOVE DIMENSIONS.

There must be a minimum flat surface area around the fireplace opening shown by the dotted lines in Fig. 4 to ensure a good seal

between the fireplace and the fire. This area should be sound enough to take the wall plugs and screws supplied for front fixing. Ensure

thatthe baseof thefireplace islevel withthe hearthand reasonablyflat toprevent thefire rocking.

Purpose built ventilation bricks or additional air vents are not normally required in the room in which the fire is fitted unless specified by

therules inforce.

IMPORTANT: When fitting any heating appliance or wallpapering a room in which one is fitted, soft wall coverings such as heat sensitive

wallpapers may become heat damaged or discoloured especially in the area above the fire. Please bear this in mind when installing or

decorating.

5.2 FLUESANDCHIMNEYS

5.2.1SITEREQUIREMENTSFOR228mmBY228mm(9inBY9in)BRICKCHIMNEY/178mm (7in)

STONEOR LINEDCHIMNEY AND125MM (5in)DIAMETER FLUE

The minimum dimensions for the fireplace opening for a brick chimney are as shown in Fig. 3. It will not normally be necessary to remove

anychair brickprovided theminimum depthis obtained.Achimney previouslyused toburn solidfuel mustbe sweptprior toinstallation.

Thechimney mustbe inspectedto ensurethat:

(a) Itserves onlyone fireplace.

(b) Itis properlysealed sothat combustionproducts donot escapefrom theflue intothe room.

(d) Anyrestriction suchas damper,register plate,etc. mustbe removedor securedin thefully openposition.

(e) Anyunderdraught ventilationor additionalair supply

enteringthe fireplaceor onthe hearthmust be

sealedoff.

(f) Itmust haveat least3 metreeffective flueheight.

(g) Itmust havea positiveupdraught.

CHECKTHE FLUEFOR GOODDRAUGHT

Applya lightedpaper orsmoke matchto thetop ofthe

openingin thefireplace. Observeif thereis adefinite flow

intothe chimneyand ifso proceedwith fittingthe fire.

Ifno flowis indicated,warm thechimney forseveral minutes

andthen re-check.If downdraughtis observeda suitable

terminalmust befitted andthe chimneyre-checked.

Ifpersistent no-flowor downdraughtcondition isobserved

DONOT FITTHE FIRE,SEEK EXPERTADVICE.

5.0 CONDITIONS OF INSTALLATION

8 8

505 mm MIN

406 mm MIN

457 mm MAX

Fig. 3

210 mm

MIN

550 mm MIN

572 mm MAX

610 mm MIN

5.2.2PRE-CAST FLUEOF MINIMUMSIZE (Fig.4)

Thisfire canbe installedinto aproperly constructedpre-cast

flue conforming to B.S. 1289 : 1975 or B.S. 1289 : Part 1 :

1986 or B.S. 1289 : Part 2 : 1989 of at least 3 metres

effective height and having flueways of at least 198mm by

67mm or equivalent cross-sectional area with no dimension

less than 63mm. The fireplace opening width must be

between a maximum 457mm and a minimum 406mm. The

fireplace opening height must be between a maximum of

572mm and a minimum 550mm and a depth of at least

120mmabove thehearth level.

NOTES:

1. The minimum dimensions for the flat area around the

openingare 610mm highx 505mmwide.

2. Theflue spigotrestrictor MUSTNOT befitted.

Ensure that any mortar fangs between the blocks do not

protrude into the flueways and if raking blocks are used they

are fitted according to the manufacturers instructions and

mortar is not allowed to drop down and accumulate in the

rakedportions.

CHECK THE FLUE FOR GOOD DRAUGHT AS DETAILED

INSECTION 5.2.1.

NOTE:ONLY SUITABLE FORDRY LINEDWALLS

On pre-cast flue installations the walls must be dry lined

over the route of the flue. Dry lining is the use of

plasterboard with an air space between the wall and the

plaster board. Installation must not be made into pre-cast

flues that have plaster applied directly to the surface of the

wall i.e. wet lined, because experience has shown that in

some wet lined installations the lack of heat insulation

provided by plaster can cause the plaster to shrink or crack

and other decoration such as wallpaper to discolour or

detatchfrom the wall.

5.2.3REBATED SURROUNDINSTALLATION

When fitting the fire to a pre-cast flue it is possible to use a

152mm deep rebated surround. Two optional extras are

requiredas follows:-

PartNumber

ClosurePlate 989571

Spigot 989568

Fit the closure plate to the wall ensuring that a good seal is

made between the plate and the wall. The plate has been

designed to sit on the floor behind the rebated surround or

hearth. This will position the spigot opening at the correct

height for the spigot when using a 50mm high hearth. If your

hearthis ofa differentheight repositionaccordingly.

If using a concealed gas connection ensure it is installed

before fitting the closure plate. Knock-outs are provided for

gaspiping.

Fit the spigot to the rear of the fire using the four screws

provided in the screw pack. Refer to Figures 5 and 6.

Proceedas follows:-

Positionthe spigoton therear ofthe fire.

Screw from inside the canopy into the spigot. It is easiest to

starteach screwbefore tighteningfully.

DONOTFITTHE RESTRICTOR

PRE-CAST FLUE INSTALLATION

50mm MINIMUM (2in)

120mm MINIMUM (4 /i n)

9 9

Fig. 4

505 MIN*505 MIN*

572 MAX

550 MIN

572 MAX

550 MIN

457 MAX

406 MIN

457 MAX

406 MIN

120mm

MIN

120mm

MIN

610 MIN*610 MIN*

Fig 5.

Fig 6.

Fig 7.

4 SPIGOT SCREWS

660.0

560.5

500.0

244.0

46.5

100.0

GAS SUPPLY PIPE KNOCK OUTS

78.0

10 10

Autres manuels pour RIVIERA

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Robinson Willey Cheminée intérieure

Robinson Willey

Robinson Willey Firegem Visa Super Deluxe Note de version

Robinson Willey

Robinson Willey ATHENA LF LPG Instructions de fonctionnement

Robinson Willey

Robinson Willey SuperEco Desire Manuel utilisateur

Robinson Willey

Robinson Willey Sahara Guide de l'utilisateur

Robinson Willey

Robinson Willey ATHENA R.S. A99011 Instructions de fonctionnement

Robinson Willey

Robinson Willey Sahara LF Manuel utilisateur

Robinson Willey

Robinson Willey firecharm lf Fiche technique

Robinson Willey

Robinson Willey RIVIERA Manuel utilisateur

Robinson Willey

Robinson Willey Sahara Guide de l'utilisateur

Robinson Willey

Robinson Willey RIVIERA Manuel utilisateur

Robinson Willey

Robinson Willey RIVIERA RS Note de version

Robinson Willey

Robinson Willey ATHENA R.S. Guide de l'utilisateur

Robinson Willey

Robinson Willey Sahara LF Guide rapide

Robinson Willey

Robinson Willey Sahara Guide de l'utilisateur

Robinson Willey

Robinson Willey A88028 Guide de l'utilisateur

Robinson Willey

Robinson Willey SuperEco Contemporary Manuel utilisateur

Robinson Willey

Robinson Willey 32 689 43 Instructions de fonctionnement

Robinson Willey

Robinson Willey BLACK KNIGHT 2 Note de version

Robinson Willey

Robinson Willey firecharm lf Instructions de fonctionnement

Robinson Willey

Robinson Willey A99003 Guide de l'utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation