Robern VESPER EDGELINE LIGHTS Manuel utilisateur

Part no. 209-1330 01/06/21

Vesper Edgeline Lights

800.877.2376 www.robern.com

TOOLS NEEDED / PARTS - 3

ASSEMBLING THE BRACKETS - 5

MOUNTING THE BRACKETS TO THE CABINET - 6

MOUNTING THE BRACKETS BETWEEN CABINETS - 7

ACCESS THE ELECTRICAL ENCLOSURE - 8

RECESSED INSTALLATION - 9

SURFACE INSTALLATION - 11

FINAL ASSEMBLY - 14

PRODUCT ALIGNMENT - 16

This instruction sheet contains information on how to install the Vesper Edgeline Lights. This series comes in many variations. Please

refer to the box or product label for the specic model number. A key is provided on page 2.

Save these instructions for future use and reference. An improper installation voids the warranty. Carefully inspect the lights for

damage. Installed products cannot be returned.

If you experience any problems with your lights, contact your dealer or Robern directly.

Limited Warranty — One Year Term

VESPER™EDGELINE LIGHTS

Installation Instructions

Important safety instructions - Save these instructions

Suitable for damp locations

CONTENTS

GENERAL INFORMATION

Part no. 209-1330 01/06/21

Vesper Edgeline Lights

800.877.2376 www.robern.com

For dimmable models Robern recommends the Maestro® C•L® Dimmer from LUTRON®, Model # MACL-153M.

http://www.lutron.com/TechnicalDocumentLibrary/369613a.pdf

Other LED control dimmers may operate with this product but have not been tested or veried. It's recommended that the dimmer be

within reach of your mirror so you can adjust the brightness.

For on/off (non-dimming) operation a standard wall switch may be substituted in place of the dimmer.

DIMMER RECOMMENDATIONS

Model Numbers G L A 40 E L P S 3D

Product Line G = Vesper

L = Lights

A = 1-3/8" / 35 mm

30 = 30" / 762 mm

36 = 36" / 914 mm

40 = 39-3/8" / 1000 mm

E = Edgeline

L = LED

3 = 3000K

P = Pair Lamp

D = Dimmable

S = Silver

Light Name

Width

Quantity of Lamps

Engine Type

Category

Type of Lamp

Color Temperature

Height

Main Body Color

Use the chart below to learn how to read your light model number. This chart references the model number for 1-3/8" W x 40" H Vesper

Edgeline Lights with a silver metal nish. Consult the Robern Price Book for a complete list of model numbers.

MODEL NUMBERS

Part no. 209-1330 01/06/21

Vesper Edgeline Lights

800.877.2376 www.robern.com

TOOLS NEEDED

[SS676]

(8) Screw, #10 x 1/2"

[SS344]

(3) Screw, #8 x 3/8"

[210-1661]

(4) Mounting Brackets

(2) Edgeline Lights

[205-3214]

(1) Electrical Enclosure

PARTS

Hardware Bag*

[216-1232]

[203-1068]

(3) #8 Lockwasher

* Depending on installation, not all parts will be used

[203-1057]

(1) 3/32" Allen Key

[219-1076]

(1) Cable Tie Holder

[203-1089]

(1) Cable Tie, 4"

[SS675]

(4) Screw, #10 x 3"

[205-3304]

(4) Adjustable

Button Receiver

[SS672]

(12) #10 Screw Cap

[203-1497]

(2) Screw, #8 x 3/8" Flat

[211-1351]

(2) Mounting Button

[203-1538]

(10) Screw, #8 x 5/8" Flat

Bag D*

[216-1230]

(2) Bag A*

[216-1227]

Bag B*

[216-1228]

(2) Bag C*

[216-1229]

Part no. 209-1330 01/06/21

Vesper Edgeline Lights

800.877.2376 www.robern.com

Unpack the Lights. Check the box thoroughly for all hardware and loose parts. Carefully inspect the xture for damage.

DANGER: Risk of personal injury. To avoid possible electrical shock, the electricity must be turned off at the circuit

breaker or fuse box before attempting any installation procedure.

DANGER: Risk of personal injury. To avoid possible electrical shock, the light xture must be properly grounded.

CAUTION: Grounding instructions for permanently connected products: This product must be connected to a grounded,

metal permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the

equipment-grounding terminal or lead on the product. All wiring should be done by a qualied licensed electrician.

IMPORTANT: Power for the lights should be provided separately from the electricity to the cabinet so that when lights are turned off,

cabinet electricity remains on.

NOTE: Requires minimum 120 VAC 15 amp circuit.

NOTE: Requires an approved compatible dimmer for installation (not included). Refer to the dimmer recommendation on page 2.

Observe all applicable electrical codes and building codes. Wire the light xtures in accordance with the electrical codes.

This xture is for indoor use only.

This installation may require the assistance of more than one person depending on your Light/Cabinet conguration.

NOTES

DANGER - RISK OF SHOCK -

DISCONNECT POWER BEFORE INSTALLATION

Part no. 209-1330 01/06/21

Vesper Edgeline Lights

800.877.2376 www.robern.com

ASSEMBLING THE BRACKETS

Note: A RH (Right Hand) installation will require the electrical enclosure to be ipped, placing the exiting low voltage wire

closer to the upper bracket.

Note: For 1.375 pair installations involving more than one cabinet, a RH installation is required.

1. Orient one of the mounting brackets [210-1661] (as shown) ensuring that the electrical access screws on the electrical enclosure

[205-3214] are pointed toward the front of the cabinet.

2. Attach the included electrical enclosure [205-3214] to the bracket using the supplied #8 screws [SS344] and lockwashers [203-1068].

SS344 SS344

203-1068 203-1068

210-1661

205-3214

Electrical

access screws

Low voltage

wire connection

Tabs always face

cabinet box

LH Installation RH Installation

Tabs always face

cabinet box

210-1661

Electrical

access screws

Electrical

access screws

Electrical

access screws

Low voltage wire

connection

Part no. 209-1330 01/06/21

Vesper Edgeline Lights

800.877.2376 www.robern.com

MOUNTING THE BRACKETS TO THE CABINET

Note: When mounting the lights between cabinets, see the following page.

1. Mount the brackets to the cabinet through the ganging locations, as shown, using the supplied #10 screws [SS676].

SS676

Part no. 209-1330 01/06/21

Vesper Edgeline Lights

800.877.2376 www.robern.com

Note: A Ganging Kit (refer to the cabinet's instructions, sold separately) is required for the following instructions. All additional

components shown in the following steps will be included with the Ganging Kit. Enough components are included to gang two lights

between cabinets.

1. Using two #8 x 3/8" screws [SS344] and two lockwashers [203-1068], attach the mounting brackets to the Electrical Enclosure.

2. Using two #10 x 1/2" screws [SS676], attach each mounting bracket to a ganging block, included in the Ganging Kit.

3. Attach the mounting bracket assemblies to each cabinet with four #10 x 1/2" screws [SS676].

MOUNTING THE BRACKETS BETWEEN CABINETS

1 2

[203-1068]

(2) #8 Lockwasher

[SS344]

(2) Screw, #8 x 3/8"

[SS676]

(4) Screw, #10 x 1/2"

Part no. 209-1330 01/06/21

Vesper Edgeline Lights

800.877.2376 www.robern.com

ACCESS THE ELECTRICAL ENCLOSURE

Lay the cabinet on a at level surface.

1. Remove the electrical enclosure cover to access the electrical wiring connections. Set the cover aside in a safe place.

* Make proper connections

according to the dimmer

manufacturer's instructions

CIRCUIT BREAKER

120VAC

15A

DIMMER*

FIELD CONNECTION

ELECTRICAL ENCLOSURE

LINE/BLACK

NEUTRAL/WHITE

GROUND

BLACK

WHITE

GROUND

Part no. 209-1330 01/06/21

Vesper Edgeline Lights

800.877.2376 www.robern.com

RECESSED INSTALLATION

When connecting the Electrical Enclosure to the remote light, it is recommended to route the wiring so that it does not get

pinched during recessed mounting.

1. Centered on the cabinet side opposite the electrical enclosure, attach the wire control mount [219-1076] to the cabinet side by

peeling and sticking it in place.

2. Route the wire around the back the cabinet until it reaches the wire control mount.

3. There will be an excess of length (wire will accomodate two ganged 24" cabinets). Coil the excess wire and secure in place with the

provided zip tie [203-1089].

Back View

Part no. 209-1330 01/06/21

Vesper Edgeline Lights

800.877.2376 www.robern.com

RECESSED INSTALLATION

4. With the electrical cover removed, support the cabinet on the edge of the recessed opening and feed the eld wire through the eld

wire strain relief at the back of each enclosure.

5. Push the cabinet assembly into the recessed opening until the back of the cabinet ange is tight to the nished wall surface.

6. Using a level, level and plumb the products in the opening. Shim as necessary. Using a square, make sure the cabinet is square in

all axis.

7. Make the electrical connection according to the electrical diagram on page 8.

Note: Refer to your cabinet's Instructions to insure there are no additional steps required prior to proceeding.

8. Mount the cabinet in place using the #10 Screws [SS674] provided with the cabinet.

RO Width =

Width of cabinet +

width of lights - 3/4" (19 mm)

RO Height =

Height of cabinet - 3/4" (19 mm)

Table des matières

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur