ROBBE SZD-54 Manuel utilisateur
Operating
instructions
SZD-54
Art.-Nr. 3014 August 2017
Operating instructions
SZD-54
No.
3014
Thank you for purchasing the ROBBE "SZD-54". The model is a modern
moulded foam model, largely assembled, with a wide range of applications.
In order to ensure that you will enjoy the model for a long time and especially to ensure a
smooth first flight, please read this manual carefully and follow the steps exactly as they
are done.
•Pay particular attention to all safety instructions for operation of the model in order not to endanger
yourself or others!
•Due to the advancing technical developments, changes in the sen se of technical progress are
subject to change without notice.
•The construction of the model does not require extensive tooling and should also be easy for less
experienced model builders.
•Nevertheless, it is not a beginner model!
•If you are unsure, please contact one of our dealers or ask for our service. Many model flying clubs
also offer assistance.
•After purchasing the model, check the contents for completeness and damage.
•Always proceed with appropriate responsibility when operating the model to avoid causing personal
injury or property damage!
•Pay attention to valid insurance coverage!
•Fly only within the scope of the legal regulations and on permitted places!
•After finishing the flight, always remove the battery from the model!
•High heat (for example in a locked car) or extreme cold can damage the model and its components!
•Packaging or parts of packaging may endanger children! Store them immediately in a safe place.
•The use of model making articles requires knowledge and practice. Only put the model into
operation if you are sufficiently trained!
Warranty conditions:
The warranty covers 24 months from the date of purchase, material or functional defects. However, not
damage due to improper use, wear and tear, overloading or similar! Except for warranties within the
framework of statutory provisions.
No liability can be accepted for printing errors!
Technical data:
Wingspan:
Length:
All-up weight:
approx. 2120 mm
approx. 1017mm
approx. 1150 g
Motor:
Battery:
Speed controller:
Servos:
Prop:
Brushless 2820 1000 K/V
2200 mAh 3S / 11,1 Volt
Brushless 30A 2-3S Lipo , 2A BEC
4pcs. 9 g
10x8"
Radio: at least with 4-channels
Required accessories (not included in package):
•Battery 2200 mAh 3S / 11,1 Volt
•Radio control system with at least 4
channels
•suitable charger
Spare parts:
301403
301404
301405
301406
301407
301408
301409
301410
301411
301412
9744750
S2009
Wingset with decals (w/o Servos)
Fuselage with decals (w/o electronic)
Tail unit set
Canopy
Prop blades
Foldingprop set
Pushrod set
Winglets
Decals
Brushless Motor 2820
Brushless controller ro-Control 40A
Rovor S2009 9g
No.
3014
Operating instructions
SZD-54
SZD 54
SZD 54
1. Fuselage
2. Wingset
3. Elevator
4. Rudder
5. Attachment parts, surface connectors, Y-cables,
screws
6. Winglets / 2 different versions
1 2
3 4
5 6
Kit content:
No.
3014
Ope rati ng ins tru ction s
SZD-54
1. Assembly of the tailplane:
Position the tailplane as shown in the illustration at the fuselage end and
screw it tightly to the fuselage from above using the M4x25 screw. Make
sure that the screw is firmly seated and do not overtighten the screw!
2. Assembly of the rudder:
Insert the rudder into the recess provided for this purpose on the fuselage and
tighten it with screw M4x35 from below. Make sure that you also have a tight fit
without damaging the screw connection!
No.
3014
Operating instructions
SZD-54
3. Rudder connections:
The two clevis heads for the rudder and elevator must now be mounted in the
corresponding rudder horn on the 3rd hole and screwed tight.
Make sure that the screw is only tightened firmly, that the linkage remains
smooth running!
too tight!
optimal!
No.
3014
Operating instructions
SZD-54
4. Assembly of the wings:
The two wing halves are attached to the fuselage by means of CRP tube
10mm. At the same time, thread the servo connection cable through the hole
provided on the fuselage and make sure that the servo cable is not jammed!
The wings are secured to the underside of the wing by means of a screw on
the underside of the wing. Make sure that you are seated safely without
damaging the screw connection by stretching it over!
The two winglets have to be fixed to the edging arch with screws M3x10.
No.
3014
Operating instructions
SZD-54
5. Electrical connection:
Now all servos must be connected to the receiver according to the sequence
of connections of your remote control system. If your remote control system
cannot handle two aileron servos, the model is supplied with a V-cable for
one receiver channel.
The controller is also connected to the receiver.
6. Final adjustments:
Next, all rudder functions and engine control on the transmitter must be set.
In case of rudder deflections, we recommend that you use the following
values for your first flight, which you can later adjust to suit your personal
preferences.
ATTENTION: We recommend that you disassemble the propeller for safety
reasons during all adjustment work on the remote control system in order to
avoid injuries caused by e. g. sudden starting of the engine.
Elevator Rudder Aileron
No.
3014
Operating instructions
SZD-54
7: Center of gravity:
In order to achieve maximum flight performance, a correct centre of gravity is
essential.
For the first flight, make sure that the centre of gravity of 60mm behind the
leading edge (measured at the fuselage base) is reached by moving the
battery. Ideally, the fuselage should be levelled with the correct centre of
gravity and a lightly suspended nose.
ATTENTION: if the centre of gravity is not correct, this can lead to a fall and
may result in the following lead to property damage and personal injury!
I< 60mm >I
No.
3014
Operating instructions
SZD-54
Modellbau Lindinger GmbH
Industriestrasse 10
4565 Inzersdorf im Kremstal
AUSTRIA
Modellbau
Made in China
2
www.robbe.com
8. Tips and notes for the first flight:
Before the first flight, check again that all mechanical and electrical connections
are tightly connected. We also recommend to check this before every flight, as
well as the direction of action of the control deflections!
ATTENTION: Loose wings, or other parts of the model may cause a crash. lead
to property damage and personal injury!
Use the model only on suitable flying terrain and make sure not to endanger
pedestrians in the vicinity or property!
To get the model into the air, all you need to do is to push the model lightly by
hand with the motor switched on and the trajectory slightly tilted upwards. The
model should then take off slightly uphill. Otherwise, trim corrections must
establish the desired flight direction. The effectiveness of the rudders and the
individual control deflections can then be flown at a sufficient altitude. The
optimum centre of gravity can also be checked by slightly "pressing" the centre
of gravity (soft inclination downwards) and then observing the interceptor sheet.
The rule of thumb applies here, if the model's intercept sheet is too abrupt
without the need for tax inputs, the model is too top-heavy.
By contrast, the model would be too tail-heavy if it maintains its trajectory or
even tends towards the ground!
ATTENTION: A tail-weighted model is critical in flight characteristics!
This can easily lead to a crash!
4565 Inzersdorf/Kremstal, Industriestraße 10
No.
3014
Operating instructions
SZD-54
Autres manuels pour SZD-54
1
Table des matières
Autres manuels ROBBE Jouet
ROBBE
ROBBE Air Beaver Manuel utilisateur
ROBBE
ROBBE AMX-Jet Manuel utilisateur
ROBBE
ROBBE AMPLITUDE Mode d’emploi
ROBBE
ROBBE Hot Shot 3078 Mode d’emploi
ROBBE
ROBBE BLUE ARROW NANO LOOP 2.4 GHz Manuel utilisateur
ROBBE
ROBBE BK 117 Manuel utilisateur
ROBBE
ROBBE Nino 3267 Manuel utilisateur
ROBBE
ROBBE Pilatus PC21 Nano-Racer Mode d'emploi
ROBBE
ROBBE ZLIN 50LX RED BULL 1600MM ARF Mode d'emploi
ROBBE
ROBBE LIMIT PRO Mode d’emploi
ROBBE
ROBBE AIRBULL 3129 Manuel utilisateur
ROBBE
ROBBE Edge 540 ARF Manuel utilisateur
ROBBE
ROBBE millennium 60 II Manuel utilisateur
ROBBE
ROBBE Air Trainer 140 V2 Manuel utilisateur
ROBBE
ROBBE PILATUS PC-6 ARF Mode d'emploi
ROBBE
ROBBE Scirocco Mode d’emploi
ROBBE
ROBBE Spirit Fun PLUS RTF Manuel utilisateur
ROBBE
ROBBE Sopwith Pub 3126 Manuel utilisateur
ROBBE
ROBBE ARROW PLUS TRAINER EVOLUTION Manuel utilisateur
ROBBE
ROBBE Curtiss Jenny JN-4 Manuel utilisateur
