Rize Fixie Manuel utilisateur
Owner’s Manual
Model: Fixie
!
Introduction …………….…… 1
Safety Check …………….…… 2"
General Information …………….…… 3
Liability Disclaimer!…………….…… 3"
Assembly …………….…… 4
Handlebar!!!…………….…… 4"
Front Wheel! ! …………….…… 4"
Rear Wheel! ! …………….…… 5"
Tire Pressure! ! …………….…… 5"
Fenders!!!…………….…… 5"
Pedals!!!…………….…… 6"
Seat!!!…………….…… 6"
Taillight!!!…………….…… 7"
Bottle Holder! ! …………….…… 7"
Brake Lever Adjustment!…………….…… 7 "
Battery Care …………….…… 8
Battery Charging!! …………….…… 8"
Battery Storage! ! …………….…… 8"
LCD Display …………….…… 9
Switch Power ON / OFF!…………….…… 9"
Power Assist Level!…………….…… 9"
Throttle!!!…………….…… 9"
Headlight!!!…………….…… 9"
Walk Mode! ! …………….…… 10"
Data Mode Display!…………….…… 10"
Settings Mode! ! …………….…… 10"
Advance Settings!…………….…… 11"
Error Code Definition!…………….…… 12"
Maintenance …………….…… 13
Cleaning!!!…………….…… 13"
Tips!!!…………….…… 13"
Legal Requirements …………….…… 14
Serial Number! ! …………….…… 14"
Warranty ………….……… 15
i
Content
"
!
1
© 2021 Rize Bikes
ii
Introduction
Congratulations on purchasing your new Rize bike! You have
chosen a bike that will give you an unreal riding experience, and
you have chosen wisely.
Please read this Owner’s Manual carefully before using your new
e-bike. It is your reference for assembly, maintenance, and safety.
If you do not feel comfortable assembling the bike on your own, we
highly recommend that you have your bike assembled by a
qualified bicycle mechanic.
If you have questions or need assistance, please contact
us directly.
Help Center: help.rizebikes.com
Email: [email protected]
Toll Free: 1-888-600-1545
Rize on . . .
Please check the following components: handlebar, stem, pedals, crank arms, and wheels. Ensure they are properly installed
and tightened. While some of the components are pre-assembled, it is still important to make sure every component is tightened
to the indicated torque value. Failing to notice a loose component may cause it to detach during use and lead to serious injury.
•Wheels: A critical part of assembling your bike is securing the front and rear wheels, and checking the tightness of the
wheel axle nuts. Properly installed wheels are essential to the safe use of the bike. "
•Tires: Both tires must be inflated to the specifications outlined in the manual. Failing to do so will reduce performance,
increase tire wear, and compromise your safety."
•Crank: Ensure the crank pedal arms are tightened to the indicated torque value (required tools: 8mm hex key, recommended
torque 30-35 N.m).
•Brakes: Ensure brakes are working correctly and properly secured. When braking, apply the rear brake first, then the front
brake. Applying the brakes incorrectly may cause serious injury."
It is recommended to perform the above safety checks every 200 - 300 km (120 - 180 miles) or if the bike has not been used in
three weeks."
For Your Safety
Users must become accustomed to the power controls before riding. It is highly recommended that you ride your new
bike in an open area and set the power assist level to “0”. Once you feel confident operating your bike, increase the
power assist gradually.
Keeping your hands over the brake levers is good practice. If for any reason you lose control, apply the brake levers
immediately. Do not try to stop your bike using your feet, as this may cause the user to lose balance.
When walking or carrying your bike, turn off the power to avoid accidentally switching on the motor. If the motor is
accidentally switched on, immediately apply the brakes.
2
© 2021 Rize Bikes
1
Safety Check
Throttle (optional)
The throttle mechanism allows partial or full motor power to be activated. Inexperienced users
should be more cautious when first pushing the throttle. The throttle function is deactivated
when the pedal assist level is set to “0”."
*The throttle is optional and can be purchased separately. The indicated (orange) wire is used to
connect the throttle. "
$
%
3
© 2021 Rize Bikes
2
General Information
Liability Disclaimer
There are risks associated with the use of any e-bike, and it is the responsibility of the
user to understand such risks. You are responsible for your own actions while using an
electric bike. Rize Bikes is not responsible nor liable for any accidents or injuries (whether
caused by you or others) that may occur during use. We recommend contacting your
insurance provider to determine whether or not your current insurance policy covers you
in the event of an accident."
Throttle wire
(A) Handlebar (required tools: 5mm hex key, 4mm hex key)
1. Fit the handlebar into the stem.
2. Attach the clamp and screw all the bolts, then screw each individually
until securely tight (recommended torque 6 N.m).
3. Align the handlebar with the front wheel and tighten the two bolts on the
side of the stem (recommended torque 8 N.m).
(B) Front Wheel
1. Remove the brake pad protector located between the brake
pads.
2. Assemble the wheel by inserting the disc brake rotor between
the brake pads then insert the fork end onto the wheel axle.
3. Remove the nut and spring (A) from the quick release skewer.
4. Insert the quick release skewer with spring (B) pointing inward
into the right side of the wheel axle.
5. Insert spring (A) pointing inward into the left side of the quick
release skewer and tighten the nut.
6. Close the quick release lever and tighten by turning clockwise.
4
© 2021 Rize Bikes
(B)
(A)
3. Remove nut and spring (A)
( The quick release skewer is attached to the wheel )
5. Tighten
6. Close
4. Insert
3
Assembly
3. Tighten
1. Fit the handlebar
2. Tighten
(C) Rear Wheel (required tools: 18mm wrench, recommended torque 35-40 N.m)
Ensure the rear wheel is tightened at the recommended torque value.
(D) Tire Pressure
Recommended tire pressure is 50-85 psi. Tire pressure range depends on many variables so please use your discretion taking
into account your weight, cargo, terrain, temperature, the feel of traction you are experiencing while riding, and hill grades when
applicable.
The tires must be inflated to the proper psi as indicated on
the tire sidewall. Do not over-inflate or under-inflate tires.
(E) Fender (optional) (required tools: 4mm hex key, 5mm hex key, 10mm wrench)
1. Place the fender hook on the front side of the fork arch at the highest position."
2. Insert the bolt into the headlight holder and fender hook, and tighten on the fork arch."
3. Use the bolts mounted on the fork to tighten the fender stays."
*The fender is optional and can be purchased separately. "
5
© 2021 Rize Bikes
WARNING
(F) Pedals (required tools: 15mm wrench, recommended torque 35-40 N.m)
The right and left pedals are marked with an "R" or "L" on the end of the thread. The right pedal axle has a smooth surface
whereas the left pedal axle has grooves."
The pedal and crank threads are designed to line up easily. Be sure to tighten the pedals with your hand, first. It should be easy
for the first few turns. Do not force if tightening is difficult. If the tightening is difficult, stop immediately as the pedal thread is not
aligned and continuing to do so will damage the thread of the crank arm.
1. Apply a small amount of grease onto the pedal thread axle.
2. Insert the right pedal into the right crank arm. Carefully thread the pedal clockwise onto the crank, by-hand, slowly and then
fully tighten.
3. Insert the left pedal into the left crank arm. Carefully thread the pedal counter-clockwise onto the crank, by-hand, slowly
and then fully tighten.
Inserting the pedal into the wrong side, installing at the wrong angle, or failure to tighten firmly will and strip
the crank arm thread and will cause the pedal to detach.
(G) Seat
1. Open the seat tube lever, insert the seat post, and close the lever to lock.
2. Rotate the lever to adjust the lock tightness.
3. Adjust the seat angle by loosening the bolt underneath the seat. You can tilt the seat up or
down and move it forward or backward to fit your comfort (required tools: 5mm hex key,
recommended torque 25 N.m).
Do not raise the seat post beyond the minimum insertion point line. Doing so
may cause the seat post or frame to break and can result in serious injury or death.
6
© 2021 Rize Bikes
WARNING
WARNING
(H) Taillight
Taillight can conveniently and firmly snaps on to the seat.
(I) Bottle Holder (optional)
Use the screws mounted on the frame tube seat to install the bottle holder.
(J) Hydraulic Brake Lever Adjustment (required tools: 2mm hex key)
1. Tighten the indicated bolt to extend the brake lever reach.
2. Loosen the indicated bolt to shorten the brake lever reach.
Failure to carry out proper assembly, operation, and/or !
maintenance could result in serious injury or death."
7
© 2021 Rize Bikes
WARNING
Table des matières
Autres manuels Rize Vélo
