Riva RC4602SV01-2017-A Manuel utilisateur

RC4602SV01-2017-A

Quick Installation Guide

This manual provides the instructions for the quick installation and the basic configuration of your camera with

the 30x optical zoom.

1. Connect cables to IP device

Connect the required cables to the device including a power cable and a LAN cable. To see the correct

positions of all the connectors, refer to the image below.

Incorrect connection may cause malfunction or damage to your IP device.

Caution

* Model design and appearance are subject to change without any prior notice.

32-pin socket

microSD / SDHC slot

< Top View of Camera’s Main Body>

< PCB Top View >

3-pin terminal block connector

LAN connector

6-pin

terminal

block

(Digital Output)

Audio speaker

stereo jack connector

Audio microphone

stereo jack connector

8-pin

terminal

block

(Digital Input)

Please install the device after removing the bubble wrap inside the dome cover.

Caution

RC4602SV01-2017-A

2. Install IP device

1) Loosen the three screws on the

top of the camera, and detach the

safety ring from the top.

2) Twist the top of the camera

counter-clockwise to separate it from

the main body, and push the lever of

the plastic cover at the bottom of the

top outward to open it. Then, insert

the provided terminal block to the

corresponding places on the PCB.

3) Drop all the necessary cables

through the neck of the camera’s top,

and fix the top to your installed

bracket or on the designated spot.

4) Install the provided ferrite cores on

the cables by winding cables around

the ferrite cores once. Refer to the

image on the left.

5) Connect all the cables to the

corresponding connectors by referring to

the image on the previous page. Then,

close the PCB on the top of the camera.

6) Hook the safety ring to the top of

the camera while carefully holding the

camera's main body, and align the

triangle marks on the top with the

main body.

7) Twist the main body counter-

clockwise once the camera’s top and

the main body are properly aligned,

and tighten the three screws on the

top.

Note

The internal heater does not work when the device is powered via PoE.

Caution

To prevent products from damage, place the camera on stable and non-vibrating

surfaces. If the stability is in doubt, consult safety personnel for reinforcements, and then

proceed with the installation.

DI/DO cable

LAN cable

power cable

Audio cable

RC4602SV01-2017-A

3. Set the lens position

The device is a 360° rotating camera and it is fully controlled by the web user interface. Once the

installation is complete and it is properly connected to the network, please refer to the webpage user’s

manual for the camera configuration instructions.

Also, the camera is equipped with the 30x optical zoom lens with the auto focus feature, and the zoom

and focus are also fully controlled by the web user interface. Refer to the webpage user’s manual for the

zoom/focus configuration instructions.

4. Set up network environment

The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of the device from

converting the MAC address’s hexadecimal numbers, which is attached to the device. Be sure that the

device and PC are on a same area network before running the installation.

Generic IP Environment

In case of generic private network environment where IP address 192.168.XXX.XXX are used, users may

view the live streaming images on a web page using the device’s default IP address:

1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal Conversion

Chart at the end of the manual.

(The MAC address of the device is attached on the side or bottom of the device.)

2. Start the Microsoft® Internet Explorer web browser and enter the IP address of the device.

3. Web streaming and device configurations are supported through ActiveX program. When the ActiveX

installation pop-up window appears, authorize and install the ActiveX setup.exe,

MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177

Convert the last two sets of hexadecimal numbers to decimal numbers.

RC4602SV01-2017-A

Custom IP Environment

Please access our website and download necessary IPAdminTool first:

http://www.rivatech.de/en/downloads/software

IPAdminTool is a management tool, which automatically scans all of the network products for users to

perform administrative tasks, which includes network configurations, firmware update, device reboot, and

device organizations.

To modify the device’s default IP address for customized network area;

1. Find the device from the IPAdminTool’s list, and highlight the device’s name.

2. Right-click the mouse and select IP Address; IP Setup window appears.

* There are two options that are for a single device or for multiple devices respectively. For one device, click “Single”.

3. On the New Information table in the Single IP Change window, modify the last two digits of the device’s

IP address, , and modify the rest parts including subnet mask, gateway, and DNS if necessary by

checking the user’s PC network area information.

4. Input the correct ID and PW of the device (default: root / pass).

5. Click Apply to complete the modification.

Give a new unique IP address by

modifying the last two digits.

RC4602SV01-2017-A

5. View video on web page

Installation of ActiveX control

Once the device’s proper IP address has been identified, type the URL in a web browser to access the

camera. At first time access, installation window may pop up.

1. When the browser asks to install the AxUMF software, click Install to proceed.

2. When the setup installation pop-up window appears, click Install to proceed with rest of installations.

Note

Depending on system OS and Internet Explorer version, installation experience may

differ from one another. Figures described above are from Windows 7, Internet

Explorer 9 environment.

To set up the Network configuration:

1. Click Setup on the upper right of the web page. The login page is displayed as below.

2. Enter the default user name (root) and password (pass), and then select OK.

The default username

and password are:

root and pass.

RC4602SV01-2017-A

6. Reboot

Perform the following procedures to reset your device:

On the Device

1. Press the reset button for 2 seconds while the device is powered on.

2. Wait for the system to reboot.

Caution

Please do not hold the reset button for more than 2 seconds. Otherwise, the camera

may be switched to its factory default settings.

On the Camera’s Webpage

1. Go to Setup > Maintenance > Reboot.

2. Click Reboot to reboot the device.

7. Factory Default

Resetting the device back to the factory default will initialize all parameters including the IP address back to

the factory defaults. To reset back to the factory default:

On the Device

1. Press the reset button and hold it while the device is powered on.

2. Release the button after 10 seconds.

3. Wait for the system to reboot.

On the Camera’s Webpage

1. Go to Setup > Maintenance > Reset All Settings.

2. Select the items that you want to keep from the initialization among network settings, user account

information, and time zone setting.

3. Click Reset All Settings.

Note

The factory default settings can be inferred as follows:

IP address: 192.168.xx.yy

Network mask: 255.255.0.0

Gateway: 192.168.0.1

User ID: root

Password: pass

Reset Button

RC4602SV01-2017-A

8. Safe Mode

Your device will get restarted in safe mode if the device does not completely boot certain times.

The errors are mainly caused by these factors below:

* The power supply is continually unplugged certain times in the middle of system booting.

* The firmware files required for system booting are damaged.

* There are conflicts in the system settings.

You will see the page to indicate that your device is in safe mode and to guide you what to do step by

step.

Follow the instructions on the webpage according to each step.

Note

There is another method to update firmware, which is using IPAdminTool.

Please refer to ‘IPAdminTool User’s Manual.pdf’for the detailed procedure.

Note

If your device is still in safe mode after trying to update firmware, please contact your

local agency to get further assistance.

RC4602SV01-2017-A

Hexadecimal-Decimal Conversion Table

Refer to the following table when you convert the MAC address of your device to IP address.

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

Hex

Dec

111

148

185

222

112

149

186

223

113

150

187

224

114

151

188

225

115

152

189

226

116

153

190

227

117

154

191

228

118

155

192

229

119

156

193

230

120

157

194

231

121

158

195

232

122

159

196

233

123

160

197

234

124

161

198

235

125

162

199

236

126

163

200

237

127

164

201

238

128

165

202

239

129

166

203

240

130

167

204

241

131

168

205

242

132

169

206

243

133

170

207

244

134

171

208

245

135

172

209

246

136

173

210

247

100

137

174

211

248

101

138

175

212

249

102

139

176

213

250

103

140

177

214

251

104

141

178

215

252

105

142

179

216

253

106

143

180

217

254

107

144

181

218

255

108

145

182

219

109

146

183

220

110

147

184

221

Table des matières

Autres manuels Riva Caméra de sécurité

Riva

Riva RC3402HD-6211IR Manuel utilisateur

Riva

Riva RC302SV-5117 Manuel utilisateur

Riva

Riva RC3502HD-5311IR Manuel utilisateur

Riva

Riva RC5502HD-6415-05 Manuel utilisateur

Riva

Riva RC3402HD-6211R Manuel utilisateur

Riva

Riva RC4202HD Manuel utilisateur

Riva

Riva IPX5502HD-6415-05 Manuel utilisateur

Riva

Riva RC3102HD-5211 Manuel utilisateur

Riva

Riva RC6802HD-6217 Manuel utilisateur

Riva

Riva RC362HD Manuel utilisateur

Riva

Riva RC4602SV-7416A-30 Manuel utilisateur

Riva

Riva RC 4602HD Manuel utilisateur

Riva

Riva RC3402HD-6311 Manuel utilisateur

Riva

Riva RC302HD-5117 Manuel utilisateur

Riva

Riva RC4100-IN Manuel utilisateur

Riva

Riva RC100 Manuel utilisateur

Riva

Riva RC3502HD-5311 Manuel utilisateur

Riva

Riva RC362HD-6211IR Manuel utilisateur

Riva

Riva RC5510 Manuel utilisateur

Riva

Riva RC3500M Manuel utilisateur

Riva

Riva RC3202HD-6111 Manuel utilisateur

Riva

Riva RC6602HD-5311 Manuel utilisateur

Riva

Riva RC6702HD-6311 Manuel utilisateur

Riva

Riva RC6702SV-7311 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur