Risco WL S52 Caractéristiques techniques

External Wireless

Sounder

Model: WL S52

Installation and Programming Instructions

Wireless Sounder Instructions

Table of Contents

Introduction........................................................................................................... 3

Operational Functions.......................................................................................... 3

Alarm / Tamper Indication...................................................................................3

Low Battery Indication.........................................................................................3

Supervision .........................................................................................................3

Pre Alarm Indication............................................................................................3

Sounder Self Testing...........................................................................................3

LED display.........................................................................................................3

Mounting the Sounder.......................................................................................... 4

Programming the sounder................................................................................... 6

Step 1: Sounder/Receiver Communication Set up..............................................6

Step 2: Setting the Sounder Parameters.............................................................7

Strobe Control............................................................................................... 7

Strobe Blink................................................................................................... 7

Strobe Arm Squawk ...................................................................................... 7

Adjusting the Volume .................................................................................... 7

Muting Tamper.............................................................................................. 7

Setting Supervision Time .............................................................................. 8

Pre Alarm indication...................................................................................... 8

Step 3: Testing the Sounder ...............................................................................8

Communication Test ..................................................................................... 8

Diagnostics.................................................................................................... 8

Replacing Batteries .............................................................................................. 9

Technical Information........................................................................................... 9

Electrical .............................................................................................................9

Wireless..............................................................................................................9

Environment........................................................................................................9

Wireless Sounder Instructions 3

Introduction

RISCO Group's two-way External Wireless Sounder is designed to extend the

signaling capabilities of RISCO Group's WisDom and Agility wireless systems. The

wireless sounder offers an easy and flexible solution for quick installation. The

sounder is powered by its own batteries and communicates wirelessly with the

security panel.

Up to 3 wireless sounders can be assigned to a system.

Operational Functions

Alarm / Tamper Indication

Upon an alarm condition, the sounder will be activated for a period of time defined

by the system (Bell Time Out parameter).

Low Battery Indication

Upon a low battery condition a trouble indication is sent to the panel.

There are 2 types of low battery indications:

ÊRadio low battery

ÊSpeaker low battery

Supervision

Each sounder can be defined to be supervised by the panel. The system generates

a local fault signal identifying the sounder whose signal is not received during a

predefined time, followed by a report to the Alarm Receiving Center (if defined).

Pre Alarm Indication

When an entry time starts, the system transmits a pre-alarm signal to the sounder.

If the system is unset before the entry delay time expires, a cancellation signal is

sent to the sounder.

If the sounder does not receive a cancellation signal within the entry delay time, the

sounder will be activated.

Sounder Self Testing

Once placing all batteries in the battery holders or pressing on the reset switch

located on the PCB (with the tamper switch open), the sounder performs a

functional self test indicated by a strobe flash squawk sound.

LED display

The wireless sounder has 2 LEDs located on the PCB. These LEDs are

enabled when the tamper is open and 10 minutes after the tamper is closed.

Red: Indicates transmission

Yellow: Indicates a low battery

Red and Yellow (3 seconds): Confirms successful learning

Wireless Sounder Instructions

Mounting the Sounder

To mount the sounder follow this procedure:

Step 1:

Remove the Cover Screw Assembly. The screw cover is opened by asserting

thumb pressure on it and pushing outward to reveal the cover screw.

Unscrew the cover screw and hinge the lid open to approximately 45 degrees, lift

the cover away until the tongue of the hinge engages. Squeeze the two halves of

the tongue together and remove the cover.

See figure 1:

Figure 1

Step 2:

Once the cover has been removed it may be placed in the Cover Holder Clip. This

is done by placing the cover hinge into the second hinge slot just inboard of the

outer hinge slot.

See figure 2:

Figure 2

Step 3:

Using the base plate as a drilling template, mark the drill holes on the wall. Drill the

holes and insert the wall plugs.

Step 4:

Fix the sounder to the wall.

Step 5:

Access to the PCB is gained by releasing the inner cover retaining the clip and

lifting the cover upward until it locks into the raised position.

See figure 3:

Wireless Sounder Instructions 5

Figure 3

Step 6:

Insert the supplied batteries. The sounder is ready for communication set up with

the system.

Step 7:

The single Tamper switch may be fitted in two positions:

a) to provide screw cover and rear tamper.

-or-

b) to provide front cover and rear tamper.

See figure 4:

Figure 4

Step 8:

Re-attach the outer cover.

Step 9:

After the sounder is trained, close the lid and lock the Cover Screw Assembly.

Wireless Sounder Instructions

Speaker & Strobe

Batteries

(6V, Serial

Connection)

Speaker

Strobe

LEDS

Two Indication

LEDs

Reset Switch

SPEAKER

TAMPER

Radio Batteries

(3V, Parallel

Connection)

External Sounder - PCB Diagram

Programming the sounder

Programming the wireless sounder consists of the following 3 steps:

1. Setting communication between the receiver and the sounder

2. Setting sounder parameters

3. Testing the sounder

Step 1: Sounder/Receiver Communication Set up

The sounder must identify itself to the system's receiver by writing its ID into the

system. Perform according to the following steps:

1. Set the receiver to the Write mode.

NOTE:

In the WisDom , as a first step, you need to allocate the sounder in the following programming location:

Main Engineer menu> 9)Devices > 2)Sounder > 1) Allocation > Select sounder> Choose ODWS1

2. Select the sounder's ID.

3. Unpack the supplied batteries.

4. Insert two speaker batteries and three Radio batteries into the batteries holders.

5. After a squawk is heard and the sounder's strobe flashes you have 10 seconds to

press on the tamper switch for at least 3 seconds. If the sounder is successfully

recognized, the system will sound a confirmation beep and the sounder will initiate

a second squawk sound and the 2 LEDs on the sounder will flash for 3 seconds.

6. Repeat the process for other sounders in the system.

Wireless Sounder Instructions 7

Step 2: Setting the Sounder Parameters

Each sounder can be defined with different sets of parameters. The following table

describes the list of parameters of the sounder.

NOTE:

For the specific programming location of each parameter refer to the system manuals.

Strobe Control

Defines the Strobe operation mode:

¾Always Off: The strobe is deactivated

¾Follow Bell (Default): The strobe is activated when the sounder bell is

triggered

¾Follow Alarm: The strobe is activated when an alarm event occurs in the

system

Strobe Blink

Defines the number of times the strobe will flash per minute (Default 40 times per

minute). Strobe Blink options:

[1] 20 times per minute [4] 50 times per minute

[2] 30 times per minute [5] 60 times per minute

[3] 40 times per minute (Default)

Strobe Arm Squawk

The time that strobe blinking will continue when set is performed (Default: 05)

NOTE:

If the sounder’s squawk strobe is defined as NO (Refer to the Allocation section) this parameter will be

ignored.

Adjusting the Volume

Defines the sounder sound volume for the following system modes:

¾Exit / Entry: The sound produced during Exit/Entry time (Default: 0)

¾Alarm: The sound produced during alarm (Default: 9)

¾Squawk: The sound produced during squawk sounds (Default: 9)

The sound volume range is between 0 (silent) to 5 (maximum volume).

Muting Tamper

This feature disables a tamper alarm from the sounder and it is recommended to be

used when replacing the sounder's batteries.

NOTES:

1. An ongoing tamper alarm will not be disabled.

2. WisDom: This feature is controlled under the Engineer Menu (Quick key [9][2][5]). Tamper alarm

will be disabled during the current installation programming period.

3. Agility: This feature is controlled under the Grand Master menu. Tamper alarm will be disabled for

20 minutes.

Wireless Sounder Instructions

Setting Supervision Time

Specifies how often the system generates a supervision request to the sounder.

If any of the sounders does not respond to the request at least once during the

receiver supervision time, the system will regard the accessory as lost.

NOTE:

The receiver supervision time should be higher than the sounder supervision time in order to

eliminate false lost event.

Range: 00-255 minutes

Default: 58 minutes

NOTE:

WisDom: Engineer menu: 1) System > 1) Timers > 9) Accessory supervision time

Agility: Engineer menu: 1) System > 1) Timers > TX supervision

Pre Alarm indication

This wireless sounder incorporates a pre-alarm feature that enhances the security of

the system by producing a local alarm in case of sabotage.

If defined, the system sends a pre-alarm signal to the sounder at the beginning of the

entry delay. If the sounder does not receive a cancellation signal from the system at

the end of the entry time, the sounder goes into alarm mode.

NOTE:

WisDom (Ver 4.25): Engineer menu Quick key 1) System> 2)Parameters> 35)Sounder Pre alarm

Agility: Engineer menu [1][2] > Advanced > Sounder Pre alarm

Step 3: Testing the Sounder

Communication Test

The sounder communication test performs a communication test between the sounder

receiver and the system.

¾To perform a communication test:

1. Access the communication test option.

NOTE:

WisDom: Engineer menu > 9) Devices > 2) Sounders > 3) Communication test

Agility: Engineer menu > 2) Testing > 5) Sounder > 1) Communication test

2. The system sends a test signal to the sounders. A number between 00-99 indicates

the strength of the communication signal between the system and the sounder.

NOTE:

For successful communication, the strength of the signal should be higher that the sounder receiver

noise threshold level.

(WisDom: Engineer menu quick key [9][2][4], Agility: Engineer menu> 2)Testing > 1)Main unit >

1)Calibration).

Diagnostics

The Diagnostics menu enables to test parameters reflecting the operation of the

sounder:

ÊSpeaker batteries voltage: Tests the selected sounder’s speaker batteries voltage

ÊRadio batteries voltage: Tests the selected sounder’s radio's batteries voltage

ÊSounder version: Displays information regarding the sounder's version

Wireless Sounder Instructions 9

NOTE:

WisDom: User menu: 4) Maintenance > 7) Sounders > 1) Diagnostics

Agility: Engineer menu > 2) Testing > 5) Sounder > 2) Battery test > 3)Version

The diagnostic features can also be performed from the Upload/Download software, locally or

remotely.

Replacing Batteries

1. Before opening the sounder it is advised to silence the tamper alarm using the

Tamper Mute option.

2. Remove the screws on both sides of the external wireless sounder and open the

cover of the sounder upwards.

3. Insert the supplied batteries.

4. Remove the old batteries from the metal clips and replace them with the new ones.

Pay attention to the polarity.

5. Replace the cover and lock the screws.

NOTES:

Dispose of old batteries according to your local regulations.

Risk of explosion if battery is replaced by an incorrect type.

Technical Information

Electrical

Power supply 5 x CR123, 3V Lithium batteries

3 batteries for the wireless system

2 batteries for signalling

Battery lifetime 3 years (typical)

Sounder volume 105 dB @ 1 meter (3.3") - adjustable

Strobe lens Polycarbonate

Flash frequency 60 times per minute (max.)

Dimensions (HxWxD) 300x 325x70 mm (11.8 x 12.8 x 2.8 inch)

Weight (including batteries) 1 Kg (2.2lbs)

Wireless

Wireless technology Bidirectional narrow band

Frequency 868 MHz or 433MHz

Range 150m (492’) Line of sight

Monitoring YES

Modulation Type ASK

Environment

Temperature range - 25°C to 60°C

IP class IP 44

Environment class Class IV

Wireless Sounder Instructions

RTTE Compliance Statement

Hereby RISCO Group declares that this wireless sounder is in compliance with the

essential requirements and other relevant provisions of Directive 1999/5/EC.

For the CE Declaration of Conformity please refer to our website: www.riscogroup.com.

FCC Note:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

a) Reorient or relocate the receiving antenna.

b) Increase the separation between the equipment and receiver.

c) Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected.

d) Consult the dealer or an experienced radio/TV technician.

FCC ID: JE4RWRT433

IC: 6564A-RWRT433

FCC Warning

The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modifications to this equipment. Such modifications could void the user's

authority to operate the equipment.

Table des matières

Autres manuels Risco Équipement marin

Risco

Risco ProSound Instructions de montage

Risco

Risco Rokonet ProSound Instructions de montage

Risco

Risco ProSound Instructions de montage

Risco

Risco WL S42 Caractéristiques techniques

Risco

Risco WL S50 Caractéristiques techniques

Risco

Risco WL RWS401 Caractéristiques techniques

Risco

Risco RW432KPP Manuel utilisateur

Risco

Risco WL S42 Manuel utilisateur

Manuels Équipement marin populaires d'autres marques

Clarion

Clarion CMS2 Manuel de réparation

EBS

EBS M7000 Manuel utilisateur

Kongsberg

Kongsberg M3 Bathy Manuel utilisateur

NPK

NPK SCS-1002 Manuel utilisateur

Furuno

Furuno FE-800 Manuel utilisateur

Harken

Harken 1561 Manuel utilisateur

Simrad

Simrad DD15 Manuel utilisateur

Notifier

Notifier FS-BSO Manuel utilisateur

Raymarine

Raymarine ST40 Manuel utilisateur

E2S

E2S E2XS112UL Manuel utilisateur

R2Sonic

R2Sonic 2026 Manuel utilisateur

COBHAM

COBHAM SAILOR 6000 Manuel utilisateur

Clarion

Clarion GR10BT Manuel de réparation

Raymarine

Raymarine Maxiview ST80 Guide de l'utilisateur

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Instructions de montage

Raymarine

Raymarine ST60 Tridata Guide de l'utilisateur

olympia electronics

olympia electronics ΒS-531/1/MAR Manuel utilisateur

Sonic

Sonic 2024 Manuel utilisateur