Risco RP128EZ01 Manuel utilisateur

-1-

Single Zone Expander (RP128EZ01)

The RISCO RP128EZ01 is a Single Zone Expander that enables to connect any detector to RISCO system

BUS. Using the BUS connection you can ease your installation by connecting any detector in parallel

connections from any point along the wiring route. In addition you can define any detector with one of

the following zone terminations supported by the panel: NO, NC, EOL, DEOL, TEOL.

The following instructions explain how to connect to the RP128EZ01 the ProSYS.

Notes:

1. Up to 32 Single Zone Expanders can be installed on the ProSYS main BUS.

2. Up to 128 Single Zone Expanders can be assigned to the ProSYS using the BUS Zone Expander.

The following instructions explain how to connect a detector to the ProSYS BUS using the RP128EZ01.

Installation

1. Set the RP128EZ01 ID number (1-32) using DIP switches 1-5.

 SW1 (1 - 5): ID switches. Defines the Single BUS Zone Expander ID number

 SW1 - 6: Not used

ID DIP - 1 DIP - 2 DIP - 3 DIP – 4 DIP - 5 ID DIP - 1 DIP - 2 DIP - 3 DIP - 4 DIP - 5

1 Of

17 Of

2 On Of

18 On Of

3 Of

On Of

19 Of

On Of

4 On On Of

20 On On Of

5 Of

On Of

21 Of

On Of

6 On Of

On Of

22 On Of

On Of

7 Of

On On Of

23 Of

On On Of

8 On On On Of

24 On On On Of

9 Of

On Of

25 Of

On On

10 On Of

On Of

26 On Of

On On

11 Of

On Of

27 Of

On O

On On

12 On On Of

On Of

28 On On Of

On On

13 Of

On On Of

29 Of

On On On

14 On Of

On On Of

30 On Of

On On On

15 Of

On On On Of

31 Of

On On On On

16 On On On On Of

32 On On On On On

2. Wire the RP128EZ01 BUS wires Red, Black (COM), Yellow(BUS) and Green (BUS) to the

ProSYS BUS.

Notes:

For maximum operation stability, it is best NOT to exceed a total of 300 meters (1000 feet) of wiring from the

ProSYS BZ1 to the ProSYS panel or to the BUS Zone Expander.

 Wiring RP128EZ01 to the Main BUS

-2-

 Wiring RP128EZ01 to BUS Zones Expanders

Notes:

When connecting RP128EZ01 to a BUS Zone Expander wire the RP128EZ01 wires to the relevant BUS zone

expander's terminals marked as TO DEVICE.

3. Wire the RP128EZ01 zone wires, Black and White, to the detector's terminals according to the

required termination.

Notes:

The Black and White wires are equivalent to zone input terminals in the ProSYS.

NORMALLY OPEN ZONE

CONFIGURATION

ALARM

DETECTOR

END OF LINE ZONE

(N.C CONTACT)

4.7K

ALARM

DETECTOR

NORMALLY CLOSED

ZONE CONFIGURATION

ALARM

DETECTOR

BlackWhite BlackWhite White Black

END OF LINE ZONE

(N.O CONTACT)

ALARM

DETECTOR

4.7K

White Black

DOUBLE END OF LINE

ZONE CONFIGURATION

4.7K

ALARM TAMPER

zone

6.8K

DETECTOR

White Black

DOUBLE END OF LINE ZONE

WIRING FOR DOUBLE LEAF DOORS

6.8K

ALARM TAMPER

CONTACT 1

4.7K

ALARM TAMPER

CONTACT 2

White Black

TRIPLE END OF LINE

ZONE CONFIGURATION

(Grade 3 )

4.7K

ALARM TAMPER

6.8K

DETECTOR

White Black

12K

Fault/

-3-

Programming

The following section describes the programming flow for the RP128EZ01 when connected to the ProSYS.

The RP128EZ01 should be configured in the system as an input zone of an iWISE Quad BUS Detector

(iQUG3).

Programming a RP128EZ01 that is wired to the Main BUS

Step 1: Adding RP128EZ01 to the Main Unit

QUICK KEYS = [7][1][9][5]:

1. From the main installer menu press [7][1][9][5] to access the BUS Zone category.

2. Using the /keys select the ID number as set by the RP128EZ01's DIP switches

(01-32)

Note:

The bottom line in the display shows "(0:yy) Type: None". In the 0:yy designation, the 0 represents that the

RP128EZ01 is on the main unit and is not assigned to a BUS Zone Expander. The yy represents the

RP128EZ01 ID number (up to 32) as set by its DIP switches.

3. Using the /keys move to the Type field. Use the key to select the

iQUG3 type.

4. Repeat steps 2 and 3 for other RP128EZ01 Expanders.

Note:

If required you can add virtual zones to the system and assign the RP128EZ01 to these zones. Virtual zones

are cost effective. They enable to use up to 32 RP128EZ01 Expanders on the main unit without adding

physical zone expanders. To add a Virtual BUS zone expander select type VBZ08 or VBZ16 when adding a

zone expander (Quick key [7][1][2]).

Step 2: Assign RP128EZ01 to a Zone ID and set its parameters

The RP128EZ01 should be configured in the system as the input of the iWISE Quad BUS detector (iQUG3).

Note:

The parameters of the RP128EZ01 are the same as any other regular wired zone in the system, with the

exception that it should be linked to one of the zones in the system.

1. From the main installer menu press [2] to enter the Zones menu.

2. Using the /keys, select [ONE BY ONE] and press .

3. Using the numeric keys, enter the desired zone number and press .

Note:

You can select any zone number that is not defined on a Wireless Zone Expander or a BUS Zone Expander.

4. Press to access the Partitions category.

5. Define Partitions, Groups, Zone Type and Zone Sound.

6. In the Termination category select one of the following options: BUS Zone Input N/C, BUS

Zone Input EOL, BUS Zone Input DEOL, BUS Zone Input N/O, BUS Zone Input TEOL.

Press .

7. Press . Select the iQUG3 (0:yy) that the ProSYS BZ1 belongs to. The Type field will

be updated automatically when selecting the zone.

8. Press . Define the loop response time.

9. Press , assign a label and press .

10. Repeat steps 3-10 for all required ProSYS BZ1 expanders.

-4-

Programming a RP128EZ01 Wired to a BUS Zone Expander

Step 1: Adding the BUS Zone Expander to ProSYS

QUICK KEYS = [7][1][2]

1. From the main installer menu press [7][1][2] to enter the Add BUS zone expander menu.

2. Using the /keys select a BUS Zone Expander ID.

3. Using the /keys move to Type. Use the key to select a type (BZE08,

BZE16, BZE24 or BZE32 zone expander) based on the DIP switches you set on the

expander. Press .

4. Using the key, select type iQUG3 for any RP128EZ01 connected to this BUS zone

expander.

Note:

The display shows "(x:yy) Type: None" . In the x:yy designation, the x represents the BUS Zone Expander ID

number and the yy represents the RP128EZ01 ID number that is connected to the zone expander, as set by

the RP128EZ01 's DIP switches.

5. Press to move to the next RP128EZ01.

Step 2: Assign BUS Detectors to a Zone ID and set basic parameters

1. From the main installer menu press [2] to enter the Zones menu.

2. Using the /keys, select [ONE BY ONE] and press .

3. Using the numeric keys, select a zone number whose designation (x:yy) is equivalent to

the one defined for the ProSYS BZ1. (The x represents the BUS Zone Expander ID number

and the yy represents the ProSYS BZ1 ID number as set by its ID DIP switches).

Press to access the Partitions category.

4. Define Partitions, Groups, Zone Type and Zone Sound.

5. In the Termination category select one of the following options: BUS Zone Input N/C, BUS

Zone Input EOL, BUS Zone Input DEOL, BUS Zone Input N/O, BUS Zone Input TEOL.

Press

6. Press . Select the iQUG3 (x:yy) that the RP128EZ01 belongs to. The Type field will

be updated automatically when selecting the zone.

7. Press . Define the loop response time.

8. Press , assign a label and press .

9. Repeat steps 3-10 for all required RP128EZ01 expanders

Technical Specifications

Power Supply 13.8V

Current Consumption 20mA

Operating Temperature -10◦- 55◦C (14◦F – 131◦F)

EMC Statement

Hereby, RISCO Group declares that this equipment is in compliance with the essential requirements and other relevant

provisions of Directive 2014/30/EU.

For the CE Declaration of Conformity please refer to our website: www.riscogroup.com.

Contacting RISCO Group

RISCO Group is committed to customer service and product support. You can contact us through our website

www.riscogroup.com or as follows:

United Kingdom

Tel: +44-161-655-5500

support-uk@riscogroup.com

France

Tel: +33-164-73-28-50

support-fr@riscogroup.com

Italy

Tel: +39-02-66590054

support-it@riscogroup.com

Belgium (Benelux)

Tel: +32-2522-7622

support-be@riscogroup.com

China (Shanghai

Tel: +86-21-52-39-0066

support-cn@riscogroup.com

Spain

Tel: +34-91-490-2133

support-es@riscogroup.com

USA

Tel: +1-631-719-4400

support-usa@riscogroup.com

Israel

Tel: +972-3-963-7777

support@riscogroup.com

No part of this document may be reproduced in any form without prior written permission from the publisher.

Table des matières

Autres manuels Risco Extenseur

Risco

Risco Agility Wireless I/O & X10 Module Manuel utilisateur

Risco

Risco RP128EZB Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur