Ripmax WOT trainer Manuel utilisateur

Page 1

The designer

Wot Trainer - Instructions

The fascination of ight captured Chris's imagination early on in his life when he started building, from kits and plans, simple free ight

gliders and rubber powered models. By his early teens, Chris was already experimenting with his own designs, several of which have

been featured as constructional plans in various aeromodelling magazines.

It wasn't long before his ercely competitive nature started to show itself, with Chris channelling his energies into competing at

national level with his own high performance free ight gliders.

In due course, Chris became tempted by the affordability of simple and fairly reliable radio control equipment, so by 1967 he had

already designed, built and own his rst radio controlled glider. By 1976 his career in the architectural profession came to an

end when he decided to channel his knowledge and experience into a full time kit manufacturing business, 'Chris Foss Designs'. It

soon developed into one of the UK's most successful and respected R/C model businesses, offering a range of stylish and quality

products.

With the advent of reliable and advanced radio control systems, Chris was able to expand his competition ying with considerable

success. His competition highlights include becoming 1977 British National Thermal Soaring Champion, 1986 British National Scale

Champion, placing 4th at the 1986 World Scale Championships in Norway, placing 6th at the 1992 World Scale Championships in the

USA, and winning both 1992 and 1993 'Radioglide' National Thermal Soaring Championships.

In the late 70s Chris joined the local gliding club and achieved his ambition to actually y himself! A few years later he expanded into

powered ight and qualied for his Private Pilot's Licence. By 2007 Chris had accumulated 2000 ying hours in a wide variety of light

aeroplanes, including a vintage Piper Cub, Jungmann aerobatic biplane, various glider tow planes and his favourite, a Vans RV8 American

aerobatic kitplane.

Chris Foss

Page 2

Wot Trainer - Instructions

Assembling the Wot Trainer

The Wot Trainer can be assembled in one of two formats - with a tricycle

undercarriage, or as a 'tail-dragger'. The main undercarriage position

changes depending on which version you choose. For the tricycle version,

the main undercarriage mounts in the rearward position and for the tail-

dragger version, it mounts in the forward position. Use the diagram on

the right to locate the positions of the pre-tted captive mounting points

under the covering - both measurements are taken from the front of

the main engine bulkhead - then pierce the covering for each of the four

mounting bolts.

Fitting the Undercarriage and Engine

STEP 1

Locate the pre-bent dural undercarriage and main wheels. Slide a wheel mounting

bolt through one of the wheels and t a plain nut to retain the wheel. Only tighten

sufciently to stop the wheel wobbling on its bolt 'axle' and ensuring that it is free to

spin. Now slide the axle through the undercarriage, t a Nyloc nut and tighten against

the previously tted plain nut. Repeat for the second wheel. Check that both spin

freely.

STEP 2

If assembling the tricycle version, locate the nosewheel and pre-bent wire noseleg.

Slide the wheel on the noseleg as shown and note the position of the recess already

machined on the noseleg.

STEP 3

Slide a wheel collet over the axle and tighten the screw using threadlocking compound

on the screw, ensuring that it locates in the recess in the axle. Check that the wheel

spins freely.

STEP 4

Now place your engine into its mount, ensuring that the front of the propeller driver

is 5mm in front of the fuselage to give adequate clearance for the propeller. Now mark

the position of the engine mounting holes using a suitable scriber or Hole Locator tool.

If necessary, enlarge the cut-outs in the nose for the needle valve and silencer, taking

care to fuel proof any exposed wood. Remove the engine.

STEP 5

Pilot drill the engine mount for the self-tapping engine mounting screws. You may nd

it easier to spot drill the two halves of the engine mount, then remove them from the

bulkhead to drill them accurately all the way through.

140mm

278mm

Page 3

Wot Trainer - Instructions

STEP 6

If assembling the tricycle version, locate the noseleg steering arm

and slide the 'z-bend' end through it as shown. Now bolt the noseleg

nylon bearing block onto the pre-drilled bulkhead as shown. Captive

nuts are already tted in the bulkhead.

STEP 7

Slide a nylon spacer onto the noseleg and partially insert the leg into the bearing block.

Slide the steering pushrod into its pre-tted tube in the fuselage as shown and then

slide the noseleg wire through the hole in the steering arm. Ensuring that the spring

coil in the noseleg points towards the rear of the model, tighten the retaining screw in

the steering arm using thread locking compound on the screw. You may now ret the

engine mount, connect the 'z-bend' end of the throttle pushrod to the engine's throttle

lever, and screw the engine into position using the self-tapping screws supplied.

STEP 8

Locate the pre-drilled holes in the underside of the model for the dural main

undercarriage. The tricycle version uses the rearward set of holes, the tail-dragger

version uses the forward set. Carefully remove the covering from the pre-drilled

mounting holes using a sharp knife or suitable awl.

STEP 9

Hold the undercarriage in position, then bolt it in place using the four bolts supplied.

Note that captive nuts have already been installed in the fuselage for these. Ensure that

you do not over-tighten the mounting screws.

STEP 10

Prepare the fuel tank as shown. The weighted 'clunk' must be free to

move around the tank during the ight to ensure that fuel pick-up is

reliable. Bend and position the other two aluminium tubes as shown

- one to the top of the tank to vent and the other to the bottom

to ll. Slide the bung into the tank and tighten the screw to form a

leak-free seal. Do not overtighten. Check the clunk is free to move

around the tank.

STEP 11

Remove the tank bay hatch by removing the rear retaining screw. Line the base of the

fuel tank bay with a piece of foam as shown. Connect three lengths of fuel tubing to

the fuel, ll and vent pipes on the tank. Install the tank in the tank bay, sliding the tubing

through the large hole in the bulkhead.

Page 4

Wot Trainer - Instructions

STEP 12

Use more foam to pack around the tank to

hold it in position, then re-t the tank hatch

locating the dowel on the front of the hatch

in the rear of the bulkhead, and re-tting the

retaining screw.

Assembling the Tail

STEP 13

Locate the n and slot it in position at the rear

of the fuselage, ensuring the two pre-tted

retaining studs pass through the fuselage as

shown. Now turn the model over and slide the

tailplane over the studs.

STEP 14

The tailplane and n are retained using the aluminium rear skid on both the tail-dragger

and tricycle versions. Hold the n and tail correctly in position, slide the tail skid over

the exposed studs and t the two nyloc retaining nuts using a suitable spanner to

tighten. Check the tailplane and n are square to each other and the fuselage. Do not

overtighten.

Assembling the Wings

STEP 15

Prepare your aileron servo by tting the rubber grommets and brass ferrules supplied

with it. Slide it into its ply mounting tray on the wing panel and mark the positions of

its mounting holes.

STEP 16

Pilot drill the plywood tray and t the servo using the mounting screws supplied with

your radio. Note the orientation of the servo - the output should be towards the front

(leading edge) of the wing.

Page 5

Wot Trainer - Instructions

STEP 17

Centre the aileron servo and t a servo arm as shown. Locate the aileron pushrods,

metal clevises and silicon tube retainers. Screw a clevis onto the threaded end of the

pushrod so that threads protrude 2mm inside the open area of the clevis. Slide on a

tube retainer and connect the clevis to the aileron torque rod as shown.

STEP 20

Locate the aluminium wing joining tube. Slide half of it into the wing panel as shown.

Now slide on the second wing panel, ensuring that the dowel in the rear of one wing

panel locates into the pre-drilled hole in the other.

STEP 18

Holding the aileron centred, mark the position where the pushrod crosses the holes in

the servo output arm. Now form a 90° bend in the pushrod at this point.

STEP 19

Slide the servo output arm over the wire, snap on a

moulded nylon swing-in keeper as shown and cut

off any excess pushrod with a pair of side cutters or

suitable pliers.

STEP 21

You can now complete the second aileron linkage in exactly the same way as the rst.

Once complete, ensure that the ailerons are centred at their neutral position and that

both ailerons move freely without binding through their entire range of travel.

Installing the Radio and Linkages

STEP 22

Fit the rubber grommets and ferrules to your elevator,

rudder and throttle servos. Locate the servos in the

plywood radio tray as shown, noting the orientation

of the outputs. Mark the positions of their mounting

holes, pilot drill and retain using the mounting screws

supplied with your servos.

Wot Trainer - Instructions

STEP 23

Locate the nylon elevator control horn. Using the elevator pushrod as a guide to its

position on the top of the left hand elevator (looking from the rear) mark and pilot

drill its mounting hole positions. The holes in the control horn must be aligned with the

hinge line as shown in the diagram below.

STEP 26

Centre the elevator servo and elevator. Now apply threadlocking compound to the

pushrod connector's screw and tighten it to lock the pushrod in position. Test to ensure

the elevator moves through its entire range of travel without binding.

STEP 24

Now locate a pushrod connector, slide it through the elevator control horn as shown

and, using a pair of pliers, carefully t its retaining star washer. Push it down rmly so

that the connector cannot wobble, but is still able to turn.

STEP 25

Slide the connector over the elevator pushrod as shown, then screw the control horn

in place on the elevator. The screws pass through the control horn, then the elevator,

then terminate in the nylon retaining plate on the underside.

STEP 27

Fit a pushrod connector to the inner hole on the rudder servo's output arm. Now

connect the rudder pushrod's 'z'-bend' end to the outer hole on the same output arm.

Slide the connector over the noseleg steering pushrod and ret the output arm. Centre

the servo and the noseleg, then tighten the connector.

STEP 28

In exactly the same way as the elevator and referring to the diagram in STEP 23, t a

control horn and servo connector onto the right hand side of the rudder (looking from

the rear). Centre the rudder servo and rudder. Now apply threadlocking compound to

the pushrod connector's screw and tighten it to lock the pushrod in position. Test to

ensure the rudder moves through its entire range of travel without binding.

Page 6

Wot Trainer - Instructions

STEP 29

Using a pair of side cutters or suitable pliers, cut off any excess elevator or rudder

pushrod as shown.

STEP 32

Pack the radio equipment in front of the servo tray with dense foam and locate the

battery at the front, with the receiver immediately behind, under the servo tray. The

nal positions of these two items are determined once the model has been balanced.

STEP 30

Fit a further pushrod connector to the throttle servo's output arm. Slide it over the

throttle pushrod. Centre the carburettor barrel and the throttle servo and tighten the

pushrod connector's screw. Test that the throttle opens from idle to full power without

binding.

STEP 33

Fit the engine's silencer and connect the fuel line

to the carburettor. The ll line is normally plugged

once the model has been fuelled up and the vent line

connects to the pressure nipple on the silencer. Fit a

suitable propeller and tighten the propeller nut.

Final Installation

STEP 31

Fit your switch in a convenient position. The left hand side of the fuselage (looking from

the rear) on the opposite side to the exhaust is recommended.

STEP 34

Drill a small hole in the rear deck as shown. Pass the

aerial through (after tying a security knot in it) and

retain it to the top of the n using a suitable pin and

elastic band. Locate the 'peg' at the front of the wing in

the slot in the forward bulkhead. Connect the aileron

extension lead and bolt the wing in position using the

two nylon bolts supplied. Do not over-tighten.

The assembly is now complete!

Page 7

Wot Trainer - Instructions

Control throws

For initial flights, we recommend the following:

Elevator: 10mm up

10mm down

Rudder: 25mm left

25mm right

Ailerons: 8mm up

8mm down

Balancing the model

The Centre of Gravity (C/G or Balance Point) should be 89mm

(3.5") back from the leading edge of the wing at the root, this

being the centreline of the wing joining tube. This should be

measured with the fuel tank empty. Support the completed

model under the wing either side of the fuselage at this point

and add weight or adjust the position of the radio battery in

its bay as necessary to achieve a slightly nose down attitude.

A model that is not correctly balanced will not perform as

it should and, at worst, be unstable or unflyable, leading to

damage to the model or injury to yourself or others. Do not

miss out this step in completing your Wot Trainer!

Pre-flight checks

• Completely charge your transmitter and receiver batteries

before flying.

• Carefully check your model over to ensure that all screws

are tight and everything is well bonded.

• Double-check the Wot Trainer’s Centre of Gravity.

• Check the control surfaces for both the correct throw and

direction. Ensure that each surface moves freely, without any

binding.

• Check the receiver aerial is fully extended.

• Ensure the wing bolts are tight.

We recommend that your completed model is checked over

and test flown by a competent pilot. All subsequent flights

should also be supervised, and assisted where necessary, by an

experienced pilot until you are considered safe to fly the model

unsupervised. Always fly the Wot Trainer in a safe location at

a recognised club. For further information on flying in the UK,

please contact:

British Model Flying Association (BMFA)

Chacksfield House,

31 St Andrews Road,

Leicester. LE2 8RE.

Tel: (+44) 116 2440028 Fax: (+44) 116 2440645

www.bmfa.org

Distributed to your local model shop by: Ltd., 241 Green Street, Enfield, EN3 7SJ. United Kingdom

Made in China

Al wa y s fly responsibl y and safel y.

Page 8

Table des matières

Autres manuels Ripmax Jouet

Ripmax

Ripmax MINI BOLERO Manuel utilisateur

Ripmax

Ripmax Sky Spy A-ARTF68713 Manuel utilisateur

Ripmax

Ripmax WOT 4 MK2 Manuel utilisateur

Ripmax

Ripmax mini Bossanova Manuel utilisateur

Ripmax

Ripmax Hawker Hunter Manuel utilisateur

Ripmax

Ripmax Acro Wot mk2 Manuel utilisateur

Ripmax

Ripmax Trainer 40 Manuel utilisateur

Ripmax

Ripmax EF - 2000 TYPHOON Manuel du propriétaire

Ripmax

Ripmax Hellcat Slim Manuel utilisateur

Ripmax

Ripmax NANO Boomerang Manuel utilisateur

Ripmax

Ripmax Mini Wot4 Manuel utilisateur

Ripmax

Ripmax SU KHOI31 Manuel du propriétaire

Ripmax

Ripmax Zephyr Manuel utilisateur

Ripmax

Ripmax BOOMERANG TORUS Manuel utilisateur

Ripmax

Ripmax Sky Spy A-ARTF68752 Manuel utilisateur

Ripmax

Ripmax BOLERO A-ARTF6720CS Manuel utilisateur

Ripmax

Ripmax WOT 4 FOAM-E Manuel utilisateur

Ripmax

Ripmax WOT 4 Pro Mk2 Manuel utilisateur

Ripmax

Ripmax WotsWot XL Manuel utilisateur

Ripmax

Ripmax Mini Xcalibur E Jet Manuel utilisateur

Ripmax

Ripmax Chris Foss WOT Trainer A-CF001A Manuel utilisateur

Ripmax

Ripmax Super X-Blaze RTR Manuel utilisateur

Ripmax

Ripmax Trainer 40 Manuel utilisateur

Ripmax

Ripmax J!VE Fun Fly Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur