Rinnai MC-503RC Manuel utilisateur
Rinnai New Zealand Wireless Installation and Operation: C 03-09
1
WIRELESS WATER
CONTROLLER
MC-503RC Installation and Operation Manual
Entry
Controllers
MC
No. 1 No. 2 No. 3
Max Temp. Maintenance
Temp. Volume
On/Off
Water Heater
Suitability
Suitable for the following Rinnai continuous
connector and controllers:
Controllers and Transceivers.
•
•
•
•
•
•
user in accordance with these instructions. A licensed tradesperson is not required. A licensed
with a wireless controller.
Rinnai New Zealand Wireless Installation and Operation: C 03-09
has not been operated in accordance
purchase. Proof of purchase is required at
5. Servicing of the product is to be carried out
variation without notice.
Rinnai New Zealand Wireless Installation and Operation: C 03-09
3
Contents
WARNING
5
9
Transceiver Installation 10
Wireless Water Controller Installation 11
Wireless Water Controller Operation 13
Wireless and Wired Water Controllers 15
Troubleshooting
Rinnai New Zealand Wireless Installation and Operation: C 03-09
supplied.
Read these instructions to get an
overview of the steps required.
You will need
Philips screwdriver
Do the following
Wired and wireless installations
channel.
transceiver channels have been unassigned and all wireless controllers have been reset. Refer
•
•
•
Rinnai New Zealand Wireless Installation and Operation: C 03-09
5
Location and positioning
Distances
Sunlight and LCD display
Chemicals and heat
•
•
Specic to water controllers
details.
Signal strength
signal strength.
during installation.
Rinnai New Zealand Wireless Installation and Operation: C 03-09
not occur.
Servicing
Principle of operation
Water resistance
•
•
•
Rinnai New Zealand Wireless Installation and Operation: C 03-09
charge.
To replace batteries
1.
3.
5.
•
•
•
•
•
153
2 4
Insert batteries observing
the correct polarity as
indicated inside the
battery compartment
Turn battery
compartment
cover one full turn
anti-clockwise
to open
Align marks and
turn battery
compartment
cover one full turn
clockwise to
close
Rinnai New Zealand Wireless Installation and Operation: C 03-09
Ensure the power to the water heater is switched off.
Turn on the power to the water heater.
Insert batteries into the wireless controller.
1.
3.
5.
9.
10.
(C)
O R
Press for
approximately
3 seconds
(B) (D)
(E)
Press once
(A)
Press once
to start the tuning
process, this takes
approximately
5 seconds
Press once
O R
(F)
Rinnai New Zealand Wireless Installation and Operation: C 03-09
9
Ensure the power to the water heater is switched off.
appliance.
wires in the process and replace retaining screw.
1.
3.
5.
3.
Rinnai New Zealand Wireless Installation and Operation: C 03-09
10
Transceiver Installation
transceiver
1.
3.
Entry
Controllers
MC
No. 1 No. 2 No. 3
Max Temp. Maimtenance
Temp. Volume
On/Off
Water Heater
Entry
Controllers
MC
No. 1 No. 2 No. 3
Max Temp. Maimtenance
Temp. Volume
On/Off
Water Heater
Max Temp. Maimtenance
Temp. Volume
water heater
Push adhesive surface to the side of the water heater in the
desired location. Press the transceiver into the side of the water
heater for a couple of seconds.
1.
3.
2.
3.
25
58
157
167
35
Table des matières
Autres manuels Rinnai Télécommande
Rinnai
Rinnai R98LSe-ASME Manuel utilisateur
Rinnai
Rinnai MC-91-1US Manuel utilisateur
Rinnai
Rinnai CNTRLDRCINW Fiche technique
Rinnai
Rinnai CNTRLDRCIPB Guide de démarrage rapide
Rinnai
Rinnai CNTRLDRCINW Guide de démarrage rapide
Rinnai
Rinnai CNTRLDRCIPW Fiche technique
Rinnai
Rinnai Smart Port WF-60A1 Manuel
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
