Rimage Producer III 7100 Manuel utilisateur

Operator Level Diagnostic Tests

for Rimage Producer III and

Producer IIIN

Operator Level

Producer™ 7100\8100 or 7100N\8100N Perform

Diagnostic Tests

This document provides the information needed to access, select, and perform Producer III and Producer IIIN

diagnostic tests. To perform any of the diagnostic tests, you must ensure that the Producer III or Producer IIIN is

not in an error state. For information about operating and maintaining the Producer III and Producer IIIN refer to

the Rimage Producer III and Producer IIIN User Guide.

-Important! Perform only the diagnostic tests provided below. Do not attempt to perform other diagnostic

tests without the assistance of a Rimage trained technician.

Access and Select Diagnostic Tests

1. Power on the autoloader.

2. Open the front door of the autoloader.

3. Press and hold the operator button until [BUTTON DIAGNOSTICS] displays on the operator panel.

4. Release the operator button. The autoloader is in diagnostic test mode.

5. Press the operator button the same number of times as the test number and hold the button in on the last

press. The autoloader begins the diagnostic test.

For example: To start diagnostic test 3 (calibrate lift home diagnostic test), press the operator button three

times and hold it on the third press.

Tip: To display each diagnostic test number and name, press the operator button at a rate that is slow

enough so that you can read the test on the operator panel. If you passed the desired diagnostic test,

release the operator button. After the operator panel displays the 01 diagnostic test, select the desired

diagnostic test.

6. Continue with the desired diagnostic test.

Create a Disc with an Index Mark

Diagnostic test 5 requires a disc with an index mark.

Use a black permanent marker and draw a line on a disc

near the center as shown.

Note: The mark should be at least 1 mm wide and 4

mm long.

1 mm

4 mm

Operator Level Diagnostic Tests for Rimage Producer III and Producer IIIN

Diagnostic Test 3 – Calibrate Lift Home

This diagnostic test calibrates the lift arm to accurately detect the number of discs in the carousel bins.

Tip: This diagnostic test uses the carousel motor, lift motor, carousel sensor, and the lift home sensor.

1. Remove all discs from the carousel bins.

2. Place one disc in bin 1.

nCaution: Be sure that there is only one disc in bin1 and no discs in any other bin. If you attempt to

perform this test with more than one disc in the unit it will cause miscalibrations which can damage the

lift arm and recorders.

3. Access and select diagnostic test 3. Refer to page 1. The operator panel displays [CALIBRATE

DIAGNOSTIC].

The lift arm moves to the supply bin, picks up the disc and then drops the disc into the supply bin. Then, the

lift arm moves back to its home position above the printer tray. When this cycle is complete, the autoloader

restarts and exits diagnostic tests mode.

Note: Diagnostic test 3 causes the autoloader to exit diagnostic tests mode when completed. To

continue performing diagnostic tests, refer to Access and Select Diagnostic Tests on page 1.

Diagnostic Test 5 – Cycle the Lift Diagnostic

This diagnostic test cycles media between the carousel bins and the printer. During each cycle, the test locates

the index mark on the disc.

Tip: This diagnostic test uses the lift motor, printer, rotate motor, the carousel, carousel sensors, index

sensor, and the media sensor.

-Important: Use a disc with an index mark. To create a disc with an index mark, refer to Create a Disc with

an Index Mark on page 1.

1. Open the front door.

2. Place one or more discs with an index mark in any bin.

3. Access and select diagnostic test 5. Refer to page 1. The operator panel displays, [CYCLE LIFT cycle =

00000].

The lift arm moves down to the carousel and picks up the disc with an index mark on it. The printer tray

opens. The lift arm releases the disc on top of the printer tray. The lift arm picks up the disc and drops it into

a bin in the carousel.

Notes:

•The lift arm starts to pick discs from bin 1. If a disc is not in bin 1, the lift arm proceeds to the next

bin.

•The test continues to cycle media until the operator button is pressed.

4. Press the operator button to stop the test.

5. To exit diagnostic tests, refer to Exit Diagnostic Test Mode on page 2.

Exit Diagnostic Test Mode

Press the operator button 19 times and hold on the last press. The autoloader exits diagnostic test mode.

Note: To exit a test but remain in diagnostic test mode, press the operator button one time while the test is

running. (Diagnostic test 3 is an exception.)

Autres manuels pour Producer III 7100

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Rimage duplicateur de disques

Rimage

Rimage DL5200 Manuel utilisateur

Rimage

Rimage DL5200 Manuel utilisateur

Rimage

Rimage DLN5200 Instructions d'utilisation et de sécurité

Rimage

Rimage Professional 3400 Manuel utilisateur

Rimage

Rimage DL5200 Instructions d'utilisation et de sécurité

Rimage

Rimage Everest Instructions d'utilisation et de sécurité

Rimage

Rimage Professional 3400 Guide de démarrage rapide

Rimage

Rimage Producer 8200N Manuel utilisateur

Rimage

Rimage 2000i 6.5-7.1 Service Pack 1 Manuel utilisateur

Rimage

Rimage 2400 Manuel utilisateur

Rimage

Rimage 3410 Manuel utilisateur

Rimage

Rimage DLN5200 Manuel utilisateur

Rimage

Rimage Professional Endeavor Manuel utilisateur

Rimage

Rimage Professional 2450 Instructions d'utilisation et de sécurité

Rimage

Rimage 2000i 6.5-7.1 Service Pack 1 Manuel utilisateur

Rimage

Rimage DL5200 Manuel d'utilisation et d'entretien

Rimage

Rimage 3410 Manuel utilisateur

Rimage

Rimage Professional 5100N Manuel utilisateur

Rimage

Rimage Allegro 100 Instructions d'utilisation et de sécurité

Rimage

Rimage Perfect Image Manuel de la liste des pièces

Rimage

Rimage Allegro 20 Instructions d'utilisation et de sécurité

Rimage

Rimage Producer III 7100 Manuel utilisateur

Rimage

Rimage Producer IIIN+ 7100N Instructions d'installation

Rimage

Rimage 2000i 6.5-7.1 Service Pack 1 Manuel utilisateur

Manuels duplicateur de disques populaires d'autres marques

Riso

Riso CV Series Manuel

MicroBoards Technology

MicroBoards Technology GX-2 Manuel utilisateur

Addonics Technologies

Addonics Technologies HDUS325DX Manuel utilisateur

Carry

Carry Pro118 Manuel utilisateur

CopyPro

CopyPro PowerPro II Manuel utilisateur

Primera

Primera Max Manuel utilisateur

Logicube

Logicube EchoPlus-NG Manuel utilisateur

Silca

Silca Delta 2000 SA Manuel utilisateur

Reflex7

Reflex7 Daisy Chain Series Manuel utilisateur

Vinpower Digital

Vinpower Digital SharkCopier DC Manuel utilisateur

Codonics

Codonics Virtua E Manuel utilisateur

Octave

Octave Copy Master II Manuel utilisateur

Kanguru

Kanguru U2-DVDDUPE-S Manuel utilisateur

StarTech.com

StarTech.com 8STSATDUP11 Manuel utilisateur

DUPLO SEIKO CORPORATION

DUPLO SEIKO CORPORATION Duprinter DP-460 Manuel utilisateur

Addonics Technologies

Addonics Technologies UDFH7 Manuel utilisateur

Vinpower Digital

Vinpower Digital MiniLoader VDX-1 Manuel utilisateur

Addonics Technologies

Addonics Technologies CFASTD5 Manuel utilisateur