Rikon Power Tools 10-350 Manuel utilisateur

14” Professional Bandsaw

Owner’s Manual

For more information:

www.rikontools.com or [email protected]

For Parts or Questions:

[email protected] or 877-884-5167

Record the serial number and date of purchase

in your manual for future reference.

Serial number:

Date of purchase:

Part #10-350M1

Models: 10-350/10-350BAL

Operator Safety: Required Reading

IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following

instructions must be followed at all times.

There are certain applications for which this tool was designed. We strongly recommend that this tool not be modied and/

or used for any other application other than that for which it was designed. If you have any questions about its application,

do not use the tool until you have contacted us and we have advised you.

General Safety Warnings

KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tool’s applications, work

capabilities, and its specic potential hazards.

ALWAYS KEEP VISITORS AWAY FROM RUNNING MACHINES.

All visitors should be kept a safe distance from the work area.

ALWAYS MAKE THE WORKSHOP CHILDPROOF.

Childproof with padlocks, master switches, or by removing starter keys.

NEVER OPERATE A TOOL WHILE UNDER THE INFLUENCE OF DRUGS,

MEDICATION, OR ALCOHOL.

ALWAYS WEAR PROPER APPAREL.

Never wear loose clothing or jewelry that might get caught in moving parts. Rubber-soled footwear is

recommended for the best footing.

ALWAYS USE SAFETY GLASSES AND WEAR HEARING PROTECTION.

Also use a face or dust mask if the cutting operation is dusty.

NEVER OVERREACH.

Keep your proper footing and balance at all times.

ALWAYS GROUND ALL TOOLS.

If your tool is equipped with a three-pronged plug, you must plug it into a three-hole electric receptacle.

If you use an adapter to accommodate a two-pronged receptacle, you must attach the adapter plug to a

known ground. Never remove the third prong of the plug.

ALWAYS AVOID DANGEROUS ENVIRONMENTS.

Never use power tools in damp or wet locations. Keep your work area well lighted and clear of clutter.

ALWAYS REMOVE THE ADJUSTING KEYS AND WRENCHES FROM TOOLS AFTER USE.

Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before

turning it on.

ALWAYS KEEP YOUR WORK AREA CLEAN. Cluttered areas and benches invite accidents.

NEVER STAND ON TOOLS.

Serious injury could occur if the tool is tipped or if the cutting tool is accidentally

ALWAYS CHECK FOR DAMAGED PARTS.

Before initial or continual use of the tool, a guard or other part that is damaged should be checked to

assure that it will operate properly and perform its intended function. Check for alignment of moving

parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its

operation. A guard or other damaged parts should immediately be properly repaired or replaced.

ALWAYS DISCONNECT TOOLS.

Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters.

ALWAYS AVOID ACCIDENTAL STARTING.

Make sure switch is in “OFF” position before plugging in cord.

NEVER LEAVE TOOLS RUNNING UNATTENDED.

1. Always allow the Bandaw blade to stop before removing scrap pieces from table.

2. Always keep hands and ngers away from the blade.

3. Never attempt to saw stock that does not have a at surface, unless a suitable support is used.

4. Always hold material rmly and feed it into the blade at a moderate speed.

5. Always turn off the machine if the material is to be backed out of an uncompleted cut.

6. Adjust the upper guide about 1/8” above the material being cut.

7. Check for proper blade size and type for thickness and type of material being cut.

8. Make sure that the blade tension and blade tracking are properly adjusted.

9. Make “relief” cuts before cutting long curves.

10. Release blade tension when the saw will not be used for a long period of time.

Special Safety Rules For Bandsaws

SAVE THESE INSTRUCTIONS.

Refer to them often.

Note: This owner’s manual is not a teaching aid. Use of this owner’s manual is intended to

show assembly, adjustments, and general use.

California Proposition 65 Warning

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains

chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.Your risk from

exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in

a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to lter out

microscopic particles.

For more detailed information about California Proposition 65 log onto rikontools.com.

13-9/16” (345 mm)

13-15/16” (356 mm)

124” (3150 mm)

1/4” – 1”(6-25 mm)

21-1/16” x 19-1/16” (535 mm x 485 mm)

Left-10oRight-45 o

2163 ft/min or 4162 ft/min

3 HP (Baldor)

12.5A / 1725 RPM

230V

315 lbs

Throat width

Max. cutting depth

Blade length

Blade width

Table size

Table tilt

Blade speeds

Motor

Amps

Volts

Net weight

13-9/16” (345 mm)

13-15/16” (356 mm)

124” (3150 mm)

1/4” – 1”(6-25 mm)

21-1/16” x 19-1/16” (535 mm x 485 mm)

Left-10oRight-45 o

2132 ft/min or 4101 ft/min

2.5 HP (RIKON)

10A / 1700 RPM

220V

308 lbs

Throat Width

Max. Cutting Depth

Blade Length

Blade Width

Table Size

Table Tilt

Blade Speeds

Motor

Amps/Speed

Volts

Net weight

SafetyWarnings..................................................................................................................................................2-3

Bandsaw Safety Rules ..........................................................................................................................3

Specications ........................................................................................................................................4

Contents of Package ............................................................................................................................5

Loose Parts ...........................................................................................................................................6

Getting To Know Your Bandsaw ............................................................................................................7

Table Assembly .....................................................................................................................................8

Rip Fence Assembly .............................................................................................................................8

Hand-Wheel Assembly .........................................................................................................................8

Setting 90oTable Stop ...........................................................................................................................9

Tilting the Table .....................................................................................................................................9

Tracking Blade ......................................................................................................................................10

Adjusting Blade Tension .......................................................................................................................10

Blade Tension Indicator Adjustment.......................................................................................................10

Changing the Bandsaw Blade........................................................................................................11

Upper Blade Guide Adjustment ..........................................................................................................12

Lower Blade Guide Adjustment ..........................................................................................................12

Adjusting the Cutting Height ..................................................................................................................12

Changing Blade Speed .......................................................................................................................13

Setting Drive Belt Tension.......................................................................................................................13

Operation ............................................................................................................................................13-15

Electrical Requirements ..................................................................................................................................16

Maintenance ................................................................................................................................... ..... 17

Wiring Diagram ...................................................................................................................................17

Troubleshooting .........................................................................................................................18-19

Changing Bandsaw Tire ..................................................................................................................................19

AdjustingFence90DegreestotheTable..................................................................................................................19

Parts Diagrams/Lists ................................................................................................................................20-29

How To Guide .....................................................................................................................................30

Warranty .............................................................................................................................................31

Table of Contents

Specications

10-350 10-350BAL

Model 10-350 14” Professional Bandsaw is shipped complete in one crate. Model 10-350BAL is

shipped in two cartons unless otherwise noted.

Unpacking and Checking Contents

a. Separate all “loose parts” from packaging materials and check each item with “Table of Loose

Parts” to make sure all items are accounted for, before discarding any packaging material.

b. Thread hoist ring into threading hole on top of Bandsaw frame. This allows the user to connect

a properly secured hoist mechanism to lift the Bandsaw.

c. With the help of another person or by installing hoist ring, unbolt the Bandsaw from the packing

pallet. Properly lift the Bandsaw off the packing pallet and place on level oor.

d. Remove protective oil that is applied to the table. Use any ordinary house hold type grease or

spot remover.

e. Apply a coat of paste wax to the table to prevent rust. Wipe all parts thoroughly with a clean

Contents of Package

TABLE OF LOOSE PARTS

Item Part Name Qty

A Bandsaw Assembly 1

B Table w/insert 1

C Owner’s manual 1

D Parts Package 1 1

E Parts Package 2 1

14” Professional Bandsaw

Owner’s Manual

For more information:

www.rikontools.com

[email protected]

For Parts or Questions:

[email protected]

877-884-5167

Record the serial number and date of purchase

in your manual for future reference.

Serial number:

Date of purchase:

Part #10-350M1

Models: 10-350/10-350BAL

LIST OF LOOSE PARTS

Loose Parts List

Table assembly:

A. Table

B. Table leveling bar and hardware

C. 90° table stop bolt

D. Table mounting bolts and washers

Rip fence assembly:

A. Fence bar

B. Fence

C. Fence carrier

D. Resaw bar

Tool holder assembly:

A. L wrench 2.5MM

B. L wrench 3MM

C. L wrench 4MM

D. L wrench 5MM

E. L wrench 6MM

F. 10mm wrench

G.13mm wrench

Getting to Know Your Bandsaw

A. Hoist Ring

B. Tension Indicator Window

C. Blade Tension Hand-Wheel

D. Switch

E. Rip Fence

F. Guide Post Cap

G. Blade Tracking Window

H. Guide Post Rise/Fall Handle

I. Guide Post Lock Knob

J. Hinged Blade Guard

K. Blade Guides

L. Work Table

M. Drive Belt Tension Wheel

N. 4” Dust Ports

O. Foot Break

P. Blade Tracking Knob

Q. Quick Release Lever

R. Tool Holder

S. LED Light

T. Table Tilt & Lock Knobs

U. Power Control Box

V. Motor

Figure 1

Figure 2

Figure 3

Work Table Assembly

Installing Table Leveling Bar:

Locate the table leveling bar, two hex socket screws

and two washers (A-Fig.1 Inset).

Insert a hex socket screw and washer through the left

hole of the table leveling bar and into the threaded hole

on the left side of the blade slot (B-Fig.1). Make sure

that the opening of the slot on the right side of the table

leveling bar faces toward the table trunnion. This will

allow the table leveling bar to open outward from the

bandsaw.

Rip Fence Assembly

With a 13mm wrench, remove one 13mm hex nut and

one washer from each stud on the fence bar (A-Fig.2).

Leave one each of 13mm hex nut and washer on each

stud on the fence bar. The remaining nut and washer

will be used for drift adjustments that will be described

later in this manual.

Next, install the fence bar studs into the table as

shown (Fig.3). Locate the 13mm hex nuts and washers

removed in Fig.10 and install on the opposite ends of

each fence bar stud. NOTE: It may be necessary to

open the table leveling bar to gain access to the right

side fence bar stud.

Hand Wheel Installation

There are two hand wheels used on the 10-350

bandsaw. The rst controls the height of the upper guide

post, the second adds/removes tension on the drive

belt.

Attach the rst hand wheel (Fig.4) to the rack and pinion

shaft on the upper part of the bandsaw, using the 5mm

“L” wrench provided.

Attach the second crank handle to the belt and speed

control rod located below the 4” dust port, using the

5mm “L” wrench provided.

Assembly

Figure 4

Underside of Table

Table Leveling Bar

Blade Slot

Storage for the “L” wrenches is provided for quick

access when adjustments are needed.

Place the (4) “L” wrenches (3mm, 4mm, 5mm and 6mm)

in the tool holder on the rear column support (Fig.5).

Setting the Table Square to Saw Blade

The table may be set at 90° to the saw blade sides

by adjusting the table stop screw under the table. The

table stop screw rests on the top of the quick release

adjustment stop. By rst loosening the locking nut

(A-Fig.6) and then adjusting the screw (B-Fig.6), the

table can be set correctly. Retighten the locking nut

(A-Fig.6) making sure that the setting is maintained.

The table may also be set at 90° to the back of the saw

blade by adjusting the four trunnion micro adjustment

screws (A-Fig.7). First, slightly loosen part #98 (refer to

parts explosion on page 18 of this manual). Using the

3mm “L” wrench, turn the rear trunnion micro adjusting

screws part #125. Turning the screws clockwise will

raise the trunnion; counterclockwise will lower. Check

table for 90° and tighten part #98.

(Trunnion has been removed from bandsaw for clarity. Micro

adjusting screws are raised to exaggerate location. Only two of the

four micro adjusting screws shown.)

Tilting the Table

Loosen the lock handle (A-Fig.8) on the table trunnion.

Turn the table tilting knob (B-Fig.8) to adjust the table to

the desired angle. Use the angle indicator scale on the

trunnion bracket to nd the desired angle. Retighten the

lock handle to secure the table.

Assembly

Figure 5

Figure 6

Tool Holder

Figure 7

Figure 8

Adjustments

Tracking the Saw Blade

Unplug the bandsaw. Make sure the upper

and lower blade guides are adjusted away from the blade

and the tension scale is set to correspond to the width of

the blade you are using.

Note: The blade tension scale may read differently due to cut

specications of the blade manufacturer. It might be necessary to

increase/decrease tension up/down one size on blade tension scale to

achieve proper blade tension.

Open both doors. Loosen the lock lever (A-Fig.9) by

turning it counter clockwise and turn the blade tracking

knob (B-Fig.9) clockwise/counterclockwise while turning

the upper wheel by hand at least three rotations until the

blade tracks centered on the wheel. Finally, tighten the lock

lever and close the doors.

Adjusting the Blade Tension

The 10-350 has a quick release blade function which

allows for fast blade changing and tensioning. The quick

release lever is shown in gure 10.

To loosen the tension of the blade, turn the blade tension

handwheel (A-Fig.11) counter clockwise. To tighten the

tension of the blade, turn the blade tension handwheel

clockwise.

Tension the blade until the tension readings correspond

to the width of blade you are using by viewing through the

tension indicator window (B-Fig.11).

Note: The blade tension scale may read differently due to cut

specications of the blade manufacturer. It might be necessary to

increase/decrease tension up/down one size on blade tension scale to

achieve proper blade tension.

Always tension the blade with the quick

release lever in the “On” position. Failure to do so could

result in lack of blade tension or tension failure.

Blade Tension Indicator Adjustment

The blade tension indicator can be adjusted for

blades known to be cut over/under length by different

manufacturers. With moderate tension on the blade loosen

the two adjusting screws with a Phillips-head screw driver

(A-Fig.12). Adjust the blade indicator bracket up/down as

needed (B-Fig.12) and re-tighten the two adjusting screws.

Adjustments

Figure 9

Figure 10

Quick Release

Warning!

OnOff

Caution!

Figure 11

Figure 12

Quick Release

OnOff

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Rikon Power Tools Scie

Rikon Power Tools

Rikon Power Tools 18" Professional Bandsaw Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-325 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-336 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-306 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-305 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-345 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-110 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-110B Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-324 Mode d’emploi

Rikon Power Tools

Rikon Power Tools 10-308 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-370 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-347 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-3061 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-622VS Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 11-200 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-341 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-300 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-324TG Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 14-700 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-321 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-351 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 10-342EVS Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 15-400 Manuel utilisateur

Rikon Power Tools

Rikon Power Tools 11-600S Manuel utilisateur

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur