Right Weigh 201-EBT-04 Manuel utilisateur

ONBOARD LOAD SCALE

EXTERIOR DIGITAL |201-EBT-04(B)

LOW

WELCOME

Thank you for choosing to drive more and scale less! Here at Right

Weigh, we are commied to making our products simple to install

and easy to use. We understand that installaon can vary between

vehicles and yours may not be described in this manual. In any event,

our technical support team is ready to answer your quesons!

+61 418 622840

leigh@rwls.com.au

rightweigh.com.au

IMPORTANT!

Please read instrucons COMPLETELY and thoroughly before installaon.

Right Weigh, Inc. is not responsible or liable for product failure or vehicle

damage due to improper installaon. The installaon requirements are

outlined in this manual and should be followed thoroughly to avoid inaccuracy

or damage to the product.

It is also important to be aware of vehicle manufacturer policies before making

modiﬁcaons to the vehicle. Right Weigh, Inc. is not liable or responsible for

issues regarding warranes with other manufacturers. This is the responsibility

of the customer. If you are unsure about how these installaon pracces apply

to your vehicle, please contact your vehicle or component manufacturer.

CONTENTS

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.

and any use of such marks by Right Weigh, Inc. is under license. Other trademarks and trade

names are those of their respecve owners.

ONBOARD LOAD SCALE

EXTERIOR DIGITAL |201-EBT-04(B)

Speciﬁcaons & Overview

TCA Compliance Informaon

Scale Installaon and Electrical Connecons

Operang Modes

Tractor

Trailer / Dolly

Calibraon & Unit of Measure

Security PIN Code

Set

Change

Operate & Weigh

Mobile Device Connecon

Maintenance

Troubleshoong

Appendix A - Addional Parts

Appendix B - Wiring Insulaon

Appendix C - Esmated Steer

Revision Log

Warranty Statement

Return Policy & Repairs

The Right Weigh 201-EBT-04B digital load scale has four internal air pressure

sensors. This scale can monitor a tandem axle air suspension drive group

where all 4 air bags can have diﬀering pressures. The 4 pressures are averaged

together so that a weight can be properly calculated. The scale can also be

used to monitor 4 separate axle groups with 1 height control valve each.

SPECIFICATIONS & OVERVIEW

This load scale can be used to monitor one axle group with an air ride li axle if

the li axle air bags are controlled by the same height control valve as the other

axles in the group. The scale will need to be setup using mulple calibraon

mode. Refer to the Mulple Calibraon Mode secon for more informaon.

Drop Axle:

Independently regulated li axles cannot be considered part of an axle

group and must be in the UP posion when calibrang and weighing.

The 201-EBT-04B scale is not approved by TCA for use on vehicles with a

drop/li axle of any kind. For more informaon on TCA requirements,

refer to pages 7-8.

TCA OBM Requirement:

4 HCVs

SPECIFICATIONS & OVERVIEW

The weight of the steer axle can be esmated if this scale is used to monitor a

tractor's drive axle group. Refer to Appendix C for more informaon.

Esmated Steer Axle:

The 201-EBT-04(B) scale has the capability of connecng to a remote sensor

that has been installed on a separate vehicle, most commonly used in drop &

hook situaons. For more informaon about this feature, please refer to the

separate 403-SK Installaon Instrucon Manual (PP-003-0084).

Remote Sensor Feature:

The Remote Sensor feature is not approved by TCA and must not be

enabled. For more informaon on TCA requirements, refer to pages 7-8.

TCA OBM Requirement:

Esmated Steer is for use on tractors with a ﬁh wheel hitch only, it

will NOT work on straight trucks or car haulers. Re-calibraon is

required aer changing the posion of a sliding ﬁh wheel.

Operang Temperature: -22° F to +185° F (-30° C to +85° C)

Storage Temperature: -40° F to +185° F (-40° C to +85° C)

Power Requirement: 9 VDC to 32 VDC (Switched)

Units: Pounds (LBS) or Kilograms (KG)

Housing: High impact polycarbonate blend

Display: 0.8” LCD sunlight readable

POWER

ON/OFF

MENU/

ENTER

(1)

CAL HIGH (2)

CAL LOW (3)

DOWN ARROW

(4)

UP ARROW

62 mm

127 mm

406 mm

87 mm

184 mm

208 mm

114 mm

Technical Speciﬁcaons:

SPECIFICATIONS & OVERVIEW

TCA COMPLIANCE

INFORMATION

The 201-EBT-04B is a Transport Cerﬁcaon Australia (TCA) Type-Approved Mass

Sensor Unit (MSU) part of a Type-Approved On-Board Mass (OBM) system. This

organizaon approves automove technology that follows a set of guidelines to

ensure consumer safety and device reliability. For more informaon visit their

website at:

hps://tca.gov.au/publicaon/obm-system-speciﬁcaon/

The 201-EBT-04B is approved for use in both Category A and Category B

Type-Approved OBM systems. In order to comply with the TCA requirements, the

below guidelines MUST be followed:

OPERATING MODE

User must set the scale operang mode to either Sensor Average (AVG), Esmated

Steer + Sensor Average (S-AVG), or Independent (IDP). Mulple Calibraon (4CAL)

Mode does not comply with TCA requirements.

DROP AXLES

PIN CODE

CALIBRATION

INSTALLATION

The vehicle must not have a drop/li axle. TCA does not approve the use of this

system on vehicles with drop/li axles of any kind.

It is required that the authorized user/installer create a PIN code for the gauge to

ensure that the vehicle operator cannot tamper with the calibraon sengs. See

page 19 for informaon on how to set the PIN code.

The gauge must be calibrated before use and then re-calibrated at least once every 6

months. Each calibraon event must be recorded in the Calibraon Log (PP-003-0065

page 2).

Install the gauge using the guidelines set forth in this manual. Installaon Log

(PP-003-0065 page 1) must be completed at the me of installaon. The MSU

MUST be connected to a switched power source that is on when the ignion is on.

See pages 9-12 of this manual for detailed installaon instrucons.

REMOTE SENSOR FEATURE

The Remote Sensor feature must be disabled. This feature is not is not approved by

TCA.

Guidelines for TCA Compliance: Category A & B

TCA COMPLIANCE

INFORMATION

MAINTENANCE

TELEMATICS DEVICE

The gauge must go through the maintenance check described on page 22 at least

every 6 months. Each maintenance event must be recorded in the Maintenance Log

(PP-003-0065 page 4).

The prime mover must have an approved telemacs device installed and the device

must be connected to the Right Weigh system.

MOBILE APP

It is required that the operator use a smart phone or tablet with a mobile app to

wirelessly connect to all MSU’s (gauges) on the vehicle. If the operator is driving a

vehicle with more than one MSU, the MSU’s must be added within the app in front to

back order. Bluetooth connecon must be maintained with all MSU’s on the vehicle in

order for the weight informaon to be considered valid. Please see page 21 for more

informaon about the app.

SECURITY SEALS

Security seal kit p/n 909-SSK must be used to secure the MSU to the vehicle at the

me of installaon. See instrucons included with security seal kit for speciﬁc

installaon requirements.

Guidelines for TCA Compliance: Category B Only

SCALE INSTALLATION

& ELECTRICAL CONNECTIONS

DUMP AIR FROM SUSPENSION SYSTEM

Security seal kit p/n 909-SSK must be used to secure the MSU to the vehicle.

For more informaon on TCA requirements, refer to pages 7-8.

TCA OBM Requirement (Category B only):

Be sure to choose a locaon that is easily accessible and safe from potenal damage

(forkli posts, re caps, etc.)

DO NOT mount the scale directly to the chassis or any other main

beam unless it is approved by the vehicle manufacturer. Doing so

may void the warranty with the vehicle manufacturer.

CHOOSE LOCATION

Mount the bracket in the chosen locaon

and install the gauge box to the bracket

using supplied hardware.

The 201-EBT-04 scale is designed to be mounted on the outside of a truck or trailer,

however it must sll be mounted in a protecve enclosure. A protecve box and

mounng bracket are included with the 201-EBT-04B.

Make sure to use BOTH supplied mounng bolts to secure the

bracket to the vehicle. Using only one bolt can result in a cracked

bracket and the scale falling oﬀ the vehicle.

SCALE INSTALLATION

& ELECTRICAL CONNECTIONS

REPEAT STEPS 3-6 WITH SECOND,

THIRD, & FOURTH HCV

Each air line should go to an air bag

connected to each height control valve. If

you are measuring a drive axle group with

four separate height control valves, see

the image to the right. If you are

measuring 4 separate axle groups, make

sure one air line is connected to each axle

group being monitored.

ROUTE AIR LINE TO GAUGE

Route the new 1/4” air line from the tee ﬁng assembly to the gauge.

Secure air line with zip es. Insert the air line into the push-to-connect

ﬁng on the back of the gauge. DO NOT ROTATE THE AIR FITTING!

CUT EXISTING AIR LINE

Choose a tee ﬁng that matches the size of

the exisng air line, then install a female NPT

tube ﬁng onto the tee as shown. Use Teﬂon

tape or equivalent to seal threads, ghten

securely. For more informaon on the parts

needed for air line installaon, see Appendix A.

ASSEMBLE TEE FITTING

Cut the air line going to one of the air bags in

the suspension group to be monitored.

Insert the cut ends of the exisng air line and the

new 1/4” air line into the tee ﬁng assembly as

shown. Tighten all three tube nuts securely.

INSTALL TEE FITTING

The air ﬁngs on the back of the gauge are directly connected to the

internal circuit board. Applying ground(-) or posive(+9-32) voltage to

air ﬁngs will cause immediate air sensor failure!

Autres manuels pour 201-EBT-04

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Right Weigh Échelle

Right Weigh

Right Weigh 201-257-01 Manuel utilisateur

Right Weigh

Right Weigh 201-EBT-04B Manuel utilisateur

Right Weigh

Right Weigh 201 Series Manuel utilisateur

Right Weigh

Right Weigh 202-DDG-02 Manuel utilisateur

Right Weigh

Right Weigh 310-M3 Series Manuel utilisateur

Right Weigh

Right Weigh 201-EBT-01 Manuel utilisateur

Right Weigh

Right Weigh 510-46 Series Manuel utilisateur

Right Weigh

Right Weigh 201-EBT-02 Manuel utilisateur

Right Weigh

Right Weigh 201-EBT-04B Manuel utilisateur

Right Weigh

Right Weigh 201-257-01 Manuel utilisateur

Right Weigh

Right Weigh 201 Series Manuel utilisateur

Right Weigh

Right Weigh 202-DDG-03 Manuel utilisateur

Right Weigh

Right Weigh 201-EBT-04B Manuel utilisateur

Right Weigh

Right Weigh 201-EBT-01B Manuel utilisateur

Right Weigh

Right Weigh 201-RTS-01(B) Manuel utilisateur

Right Weigh

Right Weigh 201-EBT-04 Manuel utilisateur

Right Weigh

Right Weigh 201-EBT-01B Manuel utilisateur

Right Weigh

Right Weigh 310-PP Series Manuel utilisateur

Right Weigh

Right Weigh 201-EBT-01 Manuel utilisateur

Right Weigh

Right Weigh 202-DDG-0 Manuel utilisateur

Right Weigh

Right Weigh 202-DDG-01 Manuel utilisateur

Right Weigh

Right Weigh 201-EBT-02 Manuel utilisateur

Right Weigh

Right Weigh 510 Series Manuel utilisateur

Right Weigh

Right Weigh 202-DDG-04 Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur