RIDGID A Series Manuel utilisateur
ROCK LIGHT KIT
INSTALLATION INSTRUCTIONS
IMPORTANT
THANK YOU FOR PURCHASING RIGID INDUSTRIES’PRODUCTS FOR YOUR VEHICLE.
Please read through all of these Instructions and tips before proceeding with the installation.
We do our best to provide a simple installation process for all applications however
a professional installation is always recommended.
Always disconnect any power sources connected to your vehicle
before servicing fuses or electrical systems.
*THESE INSTRUCTIONS ARE FOR THE FOLLOWING LIGHTS:
A-SERIES ROCK LIGHT KIT (4 or 6 lights)
HARNESS/SWITCH WIRING INSTRUCTIONS
LIGHT MOUNTING INSTRUCTIONS
LIGHT WIRING INSTRUCTIONS
**Disconnect negative battery teminal before starting your installation**
**While routing wire always avoid any heat sources, sharp edges or abrasive surfaces.**
1. Mount red and black posts in desired location using provided self-tapping screws or nuts & bolts.
2. Choose a location in the vehicle cabin for switch. Drill hole for switch using ¾” step bit or holesaw.
3. Route red power wire from the battery to switch location.
4. Attach eyelet terminal from red wire to battery positive. Attach eyelet terminal from black wire to
battery negative. Route wires from battery to switch.
5. Connect spade connectors to back of switch per the drawing below.
6. Secure switch in mounting location.
**Do not reattach negative battery terminal to battery until all lights are wired.**
1. Choose mounting location for A-Series lights.
2. Choose appropriate angled or at mount pad.
3. Decide if you want to mount with self-tapping screws or nuts & bolts.
4. If using self-tapping screws, position A-Series light where you want it and run screws through black
plastic shoulder washers, then through light & mount pad and into place. Wire can be routed through
mount pad and out the side or through the mount surface (you will need to drill a hole for the wire if
you want to run it through the mount surface).
5. If using nuts & bolts, hold A-Series light in position and mark mount holes. Drill holes using ¼” bit.
If you are using the angled mount pad, holes should be drilled at a 30-degree angle. Position A-Series
light in place and insert bolts through black plastic shoulder washers, then through light & mount
pad and through surface. Secure with at washer and lock nut. If you are using the angled mount pad,
utilize the wedge washers to equalize the angle of the bolt. Wire can be routed through mount pad and
out the side or through the mount surface (you will need to drill a hole for the wire if you want to run it
through the mount surface).
1. Route light wires from each light to Red and Black posts.
2. Coil or cut any extra wire length then apply supplied crimp-on eyelets to each red and black wire
end. Secure all black wires on black grounding post with supplied nut. Secure all red wires to the red
post with supplied nut.
**At this point you may reattach the negative battery terminal to battery after all lights are wired.**
WARRANTY INFORMATION
For warranty information, visit www.rigidindustries.com/about/warranty
779 N Colorado St, Gilbert, AZ 85233 • 855-760-5337
www.rigidindustries.com
RIGID, and Rigid Industries are registered and/or common law marks owned by JST Performance, LLC, a Delaware limited
liability company d/b/a Rigid Industries.
11-12240-A
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels RIDGID Équipement d'éclairage
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
