Rice Lake CLS420 Manuel utilisateur
May 2012 131610
CLS420®Forklift Scale
Bluetooth Option Installation Instructions
Option PN 130930
Electric Shock Hazard
Warning Before opening the unit, ensure the power cord is disconnected from the power outlet.
Bluetooth Option kit 130930 is intended to replace the Lantronix Matchport WLAN module on carrier board
109266. This combination provides for a simple RS-232 to Bluetooth converter, giving the user the ability to
send and receive data from the scale indicator via a Bluetooth connection.
The Bluetooth Option Kit contains the following:
• Bluetooth Module (130929)
• Antenna (98357)
• 6” Antenna Cable (112228)
• 8” Zip Tie (58579)
Installing the Module to the Board Assembly (PN 109266)
1. Remove power from the indicator and remove the enclosure cover to gain access to the board assembly.
2. Loosen the cord grip securing the antenna in the enclosure. If the antenna cable is connected to the
enclosure, remove the nut securing it and disconnect the antenna cable from the enclosure.
3. Remove the existing WLAN module by cutting the zip tie securing the module to the board
assembly. Carefully remove the module and antenna cable assembly, and the used zip tie. See
Figure 1.
Figure 1. Remove Existing Matchport WLAN Module
2Bluetooth Option Installation Instructions
4. To install the Bluetooth option board, line up the two rows of pins with the sockets on the board
assembly - J1 designator on the option board with Pin 1 designator on the board assembly - and
carefully push the option board fully into the sockets on the board assembly. See Figure 2.
5. Run the 8” zip tie through the two holes in the board (PN 109266) and over the Bluetooth option board,
secure it snugly against the option board and trim the excess. See Figure 3.
Figure 2. Install Bluetooth Option Board
Figure 3. Secure Bluetooth Option Board
Bluetooth Option Installation Instructions 3
6. Attach the antenna.
• If the antenna cable is to be secured through the enclosure (antenna screwed on from the outside), run the
RPSMA jack on the antenna cable through the enclosure and secure with the provided lock washer and nut.
Screw the antenna on the outside of the enclosure. See Figure 4.
• If the antenna assembly is installed through a cord grip, first connect the RPSMA jack on the antenna cable
to the antenna. Then stick the antenna through the cord grip, allowing it to protrude about 1.5 to 2 inches,
and tighten the cord grip.
Note Ensure the antenna’s metal parts will not contact anything inside the enclosure when the enclosure is
reassembled. If needed, reposition the antenna, or install a piece of heatshrink tubing over the cable to
antenna connection. See figure 5.
Figure 4. Antenna Cable Secured to Enclosure
Figure 5. Antenna Installed in Cord Grip
7. Adhere one of the included MAC Address stickers to the indicator enclosure in a position convenient for
the operator to see. The second label can be used as needed.
8. Reassemble the indicator.
4Bluetooth Option Installation Instructions
Using the Bluetooth Option
The Bluetooth option operates as a simple serial to Bluetooth converter, using the Bluetooth SPP, or Serial Port
Protocol.
The device is set up to be discoverable at all times.
1. From a PC or other Bluetooth device, perform a search for available Bluetooth devices.
• The Bluetooth Option should show in the search results with its MAC address, and/or
• the name “RLWS-xxxxxx”, where xxxxxx is the last 6 digits of the MAC address.
2. To pair to the Bluetooth Option, select it from your search results (or enter its name / MAC address).
• If your device supports SSP, or Simple Secure Pairing, the devices should pair on their own.
• If you have trouble pairing in this way, or your device/program asks for a pairing key, enter the default
key “1234”.
3. Once paired, the Bluetooth Option should show as a serial communications port on your device. At this
point, you can use your software to connect to the Bluetooth Option’s serial port and communicate with the
scale indicator.
Note Theserialportinyourindicatorthatisconnectedtothe109266boardJ1(Port1)mustbesetfor19200baud,
8 bits, no parity, and 1 stop bit. J2 on the 109266 board is not used with the Bluetooth Option.
General Bluetooth Option Specifications
Specification
Operating Frequency Range (2400 ... 2483,5) MHz
Lower Guard Band 2 MHz
Upper Guard Band 3, 5 MHz
Carrier Frequency 2402 MHz ... 2480 MHz
Modulation Method GFSK (1 Mbps)
P/4 DQPSK (2 Mbps)
Hopping 1600 hops/s, 1 MHz channel space
Maximum Data Rate
GFSK Asynchronous: 723.2 kbps / 57.6 kbps
Synchronous: 433.9 kbps / 433.9 kbps
P/4
DQPSK
Asynchronous: 1448.5 kbps / 115.2 kbps
Synchronous: 869.7 kbps / 869.7 kbps
8DQPSK Asynchronous: 2178.1 kbps / 177.2kbps
Synchronous: 1306.9 kbps / 1306.9 kbps
Receiving Signal Range -82 to -20 dBm
Receiver IF Frequency 1.5 MHz
Transmission Power Min -11 ... -9 dBm
Max +14 ... +18 dBm
RF Input Impedance 50 ˟
Compliance Bluetooth Specification, Version 2.0 + EDR
Bluetooth Option Installation Instructions 5
FCC Statement
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver in connected.
• Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
• This device may not cause interference and
• This device must accept any interference, including interference that may cause undesired operation of
the device.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment End users
must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
PN131610 05/2012
Autres manuels pour CLS420
4
Table des matières
Autres manuels Rice Lake Accessoires
Rice Lake
Rice Lake 720i Manuel utilisateur
Rice Lake
Rice Lake FlexWeigh 1280 Manuel utilisateur
Rice Lake
Rice Lake Load Ranger Series Manuel utilisateur
Rice Lake
Rice Lake IQ plus 510 Manuel utilisateur
Rice Lake
Rice Lake IQ plus 510 Mode d’emploi
Rice Lake
Rice Lake MSI-8000HD Manuel utilisateur
Rice Lake
Rice Lake IQ plus 800 Manuel utilisateur
Rice Lake
Rice Lake iDimension Plus Manuel utilisateur
Rice Lake
Rice Lake Synergy 680HE Manuel utilisateur
Rice Lake
Rice Lake EZ Mount Manuel utilisateur
Rice Lake
Rice Lake MSI-8000HD Manuel utilisateur
Rice Lake
Rice Lake Revolution SURVIVOR 420HE Manuel utilisateur
Rice Lake
Rice Lake 120 Manuel utilisateur
Rice Lake
Rice Lake IQ plus 590-DC Manuel de la liste des pièces
Rice Lake
Rice Lake 520 Manuel utilisateur
Rice Lake
Rice Lake 480 Legend Series Manuel utilisateur
Rice Lake
Rice Lake iDimension Plus UPS WorldShip Guide de l'utilisateur
Rice Lake
Rice Lake Revolution 680 Synergy Plus Manuel utilisateur
Rice Lake
Rice Lake 882D Manuel utilisateur
Rice Lake
Rice Lake iDimension 100XL Manuel utilisateur
