RHINO PelcoD 2400bps on RS485 Manuel utilisateur



PTZSETUPGUIDE



For:

PelcoD2400bpsonRS485



PTZSETUPGUIDE

™©2008RhinoCoTechnologyPty.Ltd.

9HannabusPlace,McGrathsHill,NSWAustralia2756

http://www.rhinosecruity.com

Introduction

The purpose of this guide is assist in the installation, setup and use of any PTZ with any PTZ

Keyboard or compatible DVR. We recommend using only RS485 with PelcoD on 2400Bps upto 16

IDs, as this is the most common and universal format. If you cannot run a 2400Bps baudrate then we

recommend using 4800Bps, in which case you will have to consult you user manual for more

assistance.

All PTZ systems have a means of communication, this is usually RS232 or RS485. RS485 is more

commonly used as it can be run on only 2 wires and over greater distances. Some situations may

require an RS485 Repeater which can extend the distance even further. For any DVRs or PCs that

ony support RS232, an RS232 to RS485 converter may be required.

Every PTZ device runs on a protocol which is a language of communication with other PTZ devices.

For the purpose of this guide we will use only the PelcoD protocol which is used by all manufactures.

For more detailed information on any product you may need to consult the manufactures own manual.

Contents

1. PTZs:

VSPTZ55(W) Page 1.

VSSAM-SPD3300 Page 2.

VSJVC-TKC686(WP)E Page 3.

VSPTZ7722B Page 4.

2. Keyboards:

VSPTZKB Page 5.

VSSAM-SCC3100A Page 6.

3. DVRs:

DVRPLATINUM Page 7.

DVRDIAMOND Page 8.

DVRWGUARD Page 9.

DVRAPEX Page 10.

Securview VSPTZ55(W) PTZ on ID01 and Pelco-D at 2400Bps

For Power Connection:

24vAC+ Red

24vAC- Black

For 2 wire RS485 Connection:

RS485+ Orange (Rx+)

RS485- Yellow (Rx-)

ID Setting Switch

1 2 3 4 5 6 7 8 9 10

ÏÐÐÐÐÐÐÐÐÐ

Protocol Setting

1 2 3 4 5

ÐÐÏÐÐ

Samsung SPD-3300 PTZ on ID01 and Pelco-D at 2400Bps

For Power Connection:

24vAC+

24vAC-

For 2 wire RS485 connection:

RS485+

RS485-

PTZ ID

SW1 – 0

SW2 – 1

SW3 – 2

JVC TK-C686WPE PTZ on ID01 and Pelco-D at 2400Bps

For Power Connection:

24vAC+ Red

24vAC- Black

For 2 wire RS485 connection:

RS485+ Orange/White (Rx+)

RS485- Black/White (Rx-)

Setting Switch

1 2 3 4 5 6 7 8

ÏÐÐÐÐÐÐÐ

Machine ID

1 2 3 4 5 6 7 8

ÏÐÐÐÐÐÐÐ

Option Switch

1 2 3 4 5 6 7 8

ÐÐÐÐÐÏÐÐ

To access to onboard menu:

Press PRESET > 9 > 5 > ENTER

MENU = Close

SET = Open

Securview VSPTZ7722B PTZ on ID01 and Pelco-D at 2400Bps

For Power Connection:

24vAC

Ground

24vAC

-OR-

12vDC Socket

For 2 wire RS485 Connection:

RS485+ (Rx+)

RS485- (Rx-)

ID Setting Switch

1 2 3 4 5 6 7 8

ÏÐÐÐÐÐÐÐ

Simplex/Duplex Setting

1 2

ÐÐ

S2 Setting

1 2 3 4

ÐÐÐÐ

S1 Setting

1 2 3 4

ÏÐÐÐ

Securview VSPTZKB on ID01 and Pelco-D at 2400Bps

For Power Connection:

12vDC Socket

For 2 wire RS485 connection:

RS485+ (Tx+)

RS485- (Tx-)

There are 2 sets are Tx- and Tx+, either can be used.

Protocol Switch

1 2 3 4 5 6 7 8

ÐÏÏÏÏÏÏÏ

Samsung VSSAM-SCC3100A on ID01 and Pelco-D at 4800Bps

Note: The Samsung VSSAM-SCC1300A does not support a baudrate of 2400bps, and it is

therefore necessary to run any PTZ cameras on 4800bps or above.

For Power Connection:

12vDC+

12vDC-

For 2 wire RS485 connection:

Press ‘PTZ’ to enter PTZ mode. Press ‘MENU’ to enter setup, then press ‘1’ to enter ‘PTZ SETUP 1’.

Press ‘>>’ to enter ‘PTZ SETUP 2’ and then press ‘1’ to choose the model. You can then type ‘01’ on the

keypad to enter ID01 and press the ‘+/-‘ buttons to select ‘PELCO-D’ as the protocol.

Securview DVRPLATINUM on ID01 and Pelco-D at 2400Bps

For 2 wire RS485 connection on rear of DVR with additional cable:

RS485+ Red (Tx+)

RS485- White (Tx-)

Set the DVR to use the inbuilt RS485 by going to ‘Config’ > ‘System’ > ‘Serial’, and setting the Odcap to

PTZ.

Set the PTZ connection up by going to ‘Config’ > ‘PTZ’, and setting ‘Camera #’ to ‘PELCO D (2400)’

and ‘Protocol_#01’. You should also make sure that the Serial Port is set to ‘Odcap’.

Once this has been done and your PTZ is connected, you can then access the PTZ control panel by

clicking the blue arrow on the right hand side. This will give you the controls to Pan, Tilt, Zoom, and

Focus your PTZ.

Table des matières

Autres manuels RHINO Système de sécurité

RHINO

RHINO 232 Manuel utilisateur

RHINO

RHINO ADVANCED PANIC PACK Manuel utilisateur

RHINO

RHINO Watchguard Digital V2 Manuel utilisateur

RHINO

RHINO RCA-2 Manuel utilisateur

RHINO

RHINO RA96 Manuel utilisateur

RHINO

RHINO Watchguard Digital V2 Manuel utilisateur

RHINO

RHINO RA97 Manuel utilisateur

RHINO

RHINO RCA Manuel utilisateur

RHINO

RHINO 832 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur