RHINO FM60A Manuel utilisateur
© 2005Alamo Group Inc.
RHINO®
1020 S. SangamonAve.
Gibson City, IL60936
800-446-5158
Email: [email protected]
PART'S MANUAL
An Operator's Manual was shipped with the equipment in the
Manual Canister. This Operator's Manual is an integral part of
the safe operation of this machine and must be maintained
with the unit at all times. READ, UNDERSTAND, and FOLLOW
the Safety and Operation Instructions contained in this manual
before operating the equipment. If the Operator's Manual is
not with the equipment, contact your dealer or Servis-Rhino
(800-446-5158) to obtain a Free copy before operating the
equipment.
FM60A/72A
Rear Discharge
60A & 72A Rotary Mowers
Rev 11-12 Effective S/N FM60A-14000 to Current Part No. 00778236P
FM72A-15800 to Current
TO THE OWNER/OPERATOR/DEALER
Allimplementswithmovingpartsare potentiallyhazardous. Thereisno substituteforacautious, safe-mindedoperatorwho
recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to
be used with all its safety equipment properly attached to minimize the chance of accidents.
BEFOREYOUSTART!! Read the safety messages on the implement and shown in your manual.
Observe the rules of safety and common sense!
WARRANTY INFORMATION:
Readand understand the complete Warranty Statementfound inthis Manual. Fill outthe WarrantyRegistration Form
in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card
andontheWarrantyFormthatyouretain.Theuseof"will-fit"partswillvoidyourwarrantyandcancausecatastrophic
failure with possible injury or death.
PARTS
SECTION
Parts Section – 1
Parts Section – 2
©2005 Alamo Group Inc.
For maximum safety and to guarantee optimum product reliability, always use
genuine Servis-Rhino Parts. The use of inferior replacement parts may cause
premature or catastrophic failure which could result in serious injury or death.
Direct any questions regarding parts to:
The following instructions are offered to help eliminate needless delay and error in processing
purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the
basic machine featured in this manual. Part Numbers and Descriptions are given to help
locate the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organization
ordering the parts, who should be charged, and if possible, the serial number of the machine
for which the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct part
number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked and
are subject to special handling. Request a quotation for such parts before sending a
Purchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
NOTE: Please refer to The Safety Section in the front of this Manual for the proper
Part Number when ordering Replacement Safety Decals.
PARTS ORDERING GUIDE
RHINO®
1020 S. Sangamon Ave.
Gibson City, IL 60936
800-446-5158
Email: [email protected]
PART NAME INDEX
BELT ASSEMBLY 60" .......................................................................................................................................................... 14
BELT ASSEMBLY 72" .......................................................................................................................................................... 15
BLADE AND SPINDLE ASSEMBLY ..................................................................................................................... 9
CASTER WHEEL ASSEMBLY .......................................................................................................................... 12
DRIVELINE ASSEMBLY......................................................................................................................................................... 5
GEARBOX ASSEMBLY.......................................................................................................................................................... 6
OPTIONAL QUICK ATTACH HITCH KIT Rev 07-04 ........................................................................................................... 16
ROLLER- FRONT (EXTRA EQUIPMENT)........................................................................................................................... 11
SAFETY DECAL SHEETS ................................................................................................................................................... 17
SHIELD ASSEMBLY Rev 09-05............................................................................................................................................. 8
SPINDLE ASSEMBLY .......................................................................................................................................................... 10
3-POINT LIFT ASSEMBLY..................................................................................................................................................... 4
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 3
3-POINT LIFT ASSEMBLY
ITEM PART NO. QTY. DESCRIPTION
1 00757949 1 BAR TOP LINK BD80
2 00768320 4 BAR, HITCH
3 00769453 2 BAR-A-FRAME
4 00769549 2 BAR-REAR LIFT STRAP FM60A
00768319 2 BAR, REAR LIFT STRAP FM72A
5 00761724 4 BUSHING HITCH
6 00762082 6 BUSHING HITCH
7 00757953 1 BUSHING 1-1/4X7/32X3 A-FRAME
8 00603500 2 PIN, HITCH CAT I
9 37107B12 1 PIN TOP LINK CAT 1(PLATED)
10 37107B13 1 CLIP-X HAIR PIN
11 00037200 3 LOCKNUT
12 00748598 1 HEXB 3/4-10UNC 5-1/2 PL5
13 02929200 2 HHCS 3/4-10UNC 1-1/2 PL5
14 2196 2 CLIP (LYNCH PIN), 13/32 DIA.
15 02793900 4 HHCS 7/8-9UNC 2-1/2 GR 5
16 5JRC1490 4 NUT TOPLOCK 7/8 NC PLB
17 00750952 2 HEXB,5/8NC X 2-1/2,ZP,GRD5
18 00695100 4 LOCKNUT
19 00001400 4 FLATWASHER
20 00008300 2 BOLT
21 00778212 1 WDMT,DECK - FM60A
00778203 1 WDMT,DECK - FM72A
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 4
DRIVELINE ASSEMBLY
ITEM PART NO. QTY. DESCRIPTION
00768041A - DRIVELINE
1 00764500A 2 COMPLETE COLLAR YOKE
2 00756231 2 CROSS & BEARING KIT SERIES 40
3 00759169 1 PIN ROLL 8mm X 60mm
4 00759165 1 PIN ROLL INNER TUBE
5 00764506 1 COLLAR-GUARD-RETAINER
6 00754330 6 BOLT, NYLON - SAFETY SHIELD]
7 00764507 1 COLLAR-GUARD-RETAINER
8 00768168 1 SHIELD, ASY, CMPLT
9 00768165 1 DRIVELINE, HALF ASY, OUTER
10 00768164 1 DRIVELINE, ASY, INNER HALF
11 00774079 2 KIT,SLIDE COLLAR REPAIR
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 5
GEARBOX ASSEMBLY
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 6
GEARBOX ASSEMBLY
ITEM PART NO. QTY. DESCRIPTION
00777688 - ASY,GEARBOX
1 00778239 1 HOUSING GEARBOX
2 2716532 2 SNAP RING
3 2716540 1 CAP PLUG
4 00564800 1 BEARING, BALL
5 00754761 2 SHIM
6 2716564 1 SHIM KIT
7 00755615 2 BEARING
8 2716656 1 LOCKNUT
9 00778240 1 SEAL OUTPUT
10 00778241 1 SHAFT INPUT
11 00763206 1 SEAL, INPUT SHAFT
12 00754757 1 BEARING
13 00778242 1 COVER GEARBOX
14 00778243 1 SHIM
15 00755633 1 PLUG,3/8"
16 00756649 1 SNAP RING
17 00778244 1 GEAR ,CROWN
18 00772980 1 PLATE
19 00771879 1 SHIM
20 00778245 1 SHAFT, PINION
21 00778246 1 WASHER, EXTERNAL TOOTH
22 4840 1 NUT, CASTLE
23 00771856 4 BOLT METRIC
24 00778187 1 PLUG,BREATHER DIPSTICK
25 70497 1 COTTER PIN
00765444 1qt QT,ALAMO 000 GEAR LUBE
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 7
SHIELD ASSEMBLY Rev 09-05
ITEM PART NO. QTY. DESCRIPTION
1 00774843 1 PLATE GEARBOX MOUNT
2 00777538 1 SHIELD,RH MOLDED BELT FM60A
00777540 1 SHIELD,RH MOLDED BELT FM72A
3 00777539 1 SHIELD,LH MOLDED BELT FM60A
00777541 1 SHIELD,LH MOLDED BELT FM72A
4 00769933 1 NUT-PLASTIC KNOB 3/8 NC PL
5 00748823 2 HHCS 1/2-13UNC 1-1/2 PL5
6 00777688 1 ASY,GEARBOX
7 00001800 8 LOCKNUT
8 00002700 4 FLATWASHER
9 26168 6 CRG-BLT 3/8 X 1 GR5
10 00695100 4 LOCKNUT
11 00008300 4 BOLT
12 00769451 1 PLATE-GEARBOX SLIDE
13 02886900 4 CARR 1/2-13UNC 1-1/2 PL5
14 00769446 1 PLATE-GEARBOX ADJUSTMENT
15 00013901 2 NUT
16 00769898 1 BOLT 3/8 NC 4-1/2 PL2
17 02961255 6 PUSHNUT, BOLT RETAINER, 3/8
18 00758582 1 SHIELD,IMPLEMENT
19 00011700 4 LOCKWASHER
20 00023500 4 FLATWASHER
21 02958784 4 BOLT METRIC 8-P1.25- 20MM PL5
22 02030700 4 HHCS 1/2-13UNC 1-1/4 PL5
23 00011100 1 FLATWASHER 3/8 PL STD
FM60A/72A (Sep-03) Rev 09-05
©2007 Alamo Group Inc. Parts Section – 8
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels RHINO Tondeuse à gazon
RHINO
RHINO 1900 Manuel utilisateur
RHINO
RHINO BOOM ARM MOWER DB150 Manuel utilisateur
RHINO
RHINO TWISTER 10 Series Manuel utilisateur
RHINO
RHINO SE8A Manuel utilisateur
RHINO
RHINO TURBO 96 TURBO 96 Manuel utilisateur
RHINO
RHINO XM500 Manuel utilisateur
RHINO
RHINO SE42 Manuel utilisateur
RHINO
RHINO FN120 Manuel utilisateur
RHINO
RHINO FINISHING MOWERS GK6072 Manuel utilisateur
RHINO
RHINO TW60 Manuel utilisateur
RHINO
RHINO 172 Manuel utilisateur
RHINO
RHINO TM60 Manuel utilisateur
RHINO
RHINO TURBO120 TURBO120 Manuel utilisateur
RHINO
RHINO BOOM ROTARY MOWER 2160 Manuel utilisateur
RHINO
RHINO RHINO TX235 Manuel utilisateur
RHINO
RHINO SX15 Manuel utilisateur
RHINO
RHINO RHD62 Manuel utilisateur
RHINO
RHINO Turbo 120 Manuel utilisateur
RHINO
RHINO TR210 Manuel utilisateur
RHINO
RHINO FM100 Manuel utilisateur
Manuels Tondeuse à gazon populaires d'autres marques
Wolf Garten
Wolf Garten Compact plus 40 B Manuel utilisateur
Cub Cadet
Cub Cadet LTX 1045 Manuel utilisateur
Craftsman
Craftsman 917.378461 Manuel utilisateur
GGP ITALY SPA
GGP ITALY SPA CR/CS 434 SERIES Manuel utilisateur
Challenge
Challenge CH18V2 Instructions de fonctionnement
TALEN TOOLS
TALEN TOOLS AVR HGM30 Manuel utilisateur
DEWEZE
DEWEZE ATM-725 Manuel d'utilisation
Weed Eater
Weed Eater 180083 Manuel utilisateur
Husqvarna
Husqvarna Poulan Pro PP185A42 Manuel utilisateur
Better Outdoor Products
Better Outdoor Products Quick Series Manuel utilisateur
Cub Cadet
Cub Cadet 23HP Z-Force 60 Manuel d'utilisation
MTD
MTD 795, 792, 791, 790 Manuel utilisateur
