RF-Lambda REMC0218GE Manuel utilisateur

RF-LAMBDA USA www.rflambda.com

Sales: [email protected] Technical : s[email protected]

Wide Band EMC Benchtop Power Amplifier 2GHz ~ 18GHz

REMC0218GE

Rev 1. 06-10-2020

Wide Band EMC Benchtop Power Amplifier

2GHz ~18GHz

Electrical Specifications, TA= +25⁰C

Features

•Wideband Power Amplifier

•Gain: 55dB

•Output Power +50dBm typical

•Supply Voltage: 110V/220V AC

Typical Applications

•Wireless Infrastructure

•Military & Aerospace

•Test and Measurement

Parameter

Min.

Typ.

Max.

Units

Frequency Range

GHz

Gain

Gain Flatness

±5

Gain Variation Over Temperature

(-40℃~+85℃)

±3

Input VSWR

Output 1dB Compression Point (P1dB)

dBm

Saturated Output Power ( Psat)

(CW)

dBm

Isolation S12

Supply Current (110V/ 220V AC)

Efficiency at Psat

Weight

360.49

ounces

Impedance

Ohms

Input / Output Connectors

Input SMA-Female/Output N-Female

Finish

White Painted Finish

RF-LAMBDA USA www.rflambda.com

Sales: [email protected] Technical : s[email protected]

Wide Band EMC Benchtop Power Amplifier 2GHz ~ 18GHz

REMC0218GE

Rev 1. 06-10-2020

Operating Voltage

230VAC

RF Input Power

+5dBm

Step 1

Connect input and output with 50 Ohm

source/load. ( in band VSWR<1.9:1 or

>10dB return loss)

Step 2

Turn on AC power

Step 3

Enable RF output

Power OFF Procedure

Step 1

Turn off RF output power

Step 2

Turn Off AC power

Step 3

Disconnect input and output

Absolute Maximum Ratings Biasing Up Procedure

Environmental Specifications and Test Standards

Parameter Description

Operational Temperature -40℃~+85℃

(Case Temperature)

Storage Temperature -50℃~+105℃

Thermal Shock -40℃+85℃

(5 Cycles / 10 hours)

Random Vibration

MIL-STD-202G

Table 214-I, Test Condition Letter C

1.5 Hours Per Axis

High Temperature Burn In Temperature +85℃for 72 Hours

Shock

1. Weight >20g, 50g half sine wave for 11ms, Speed variation 3.44m/s

2. Weight <=20g, 100g Half sine wave for 6ms, Speed variation 3.75m/s

3. Total 18 times (6 directions, 3 repetitions per direction).

Altitude Standard: 30,000 Ft (Epoxy Sealed Controlled Environment)

Optional: Hermetically Sealed (60,000 ft. 1.0 PSI min)

Hermetically Sealed

(Optional) MIL-STD-883 (For Hermetically Sealed Units)

RF-LAMBDA USA www.rflambda.com

Sales: [email protected] Technical : s[email protected]

Wide Band EMC Benchtop Power Amplifier 2GHz ~ 18GHz

REMC0218GE

Rev 1. 06-10-2020

Ensure that the amplifier input and output ports are safely terminated into a proper 50 ohm load before turning on the power.

Never operate the amplifier without a load. A proper 50 ohm load is defined as a load with impedance less than 1.9:1 or return

loss larger than 10dB relative to 50 Ohm within the specified operating band width.

Power Supply Requirements

Power supply must be able to provide adequate current for the amplifier. Power supply should be able to provide 1.5 times the

typical current or 1.2 times the maximum current (whichever is greater).

In most cases, RF - Lambda amplifiers will withstand severe mismatches without damage. However, operation with poor loads

is discouraged. If prolonged operation with poor or unknown loads is expected, an external device such as an isolator or

circulator should be used to protect the amplifier.

Ensure that the power is off when connecting or disconnecting the input or output of the amp.

Prevent overdriving the amplifier. Do not exceed the recommended input power level.

Adequate heat-sinking required for RF amplifier modules. Please inquire.

Amplifiers do not contain Thermal protection, Reverse DC polarity or Over voltage protection with the exception of afew

models. Please inquire.

Proper electrostatic discharge (ESD) precautions are recommended to avoid performance degradation or loss of functionality.

What is not covered with warranty?

Each RF - Lambda amplifier will go through power and temperature stress testing.

Since the die, ICs or MMICs are fragile, these are not covered by warranty. Any damage to these will NOT be free to repair.

Amplifier Use

Part No. Description

REMC0218GE 2-18GHz Power Amplifier

Ordering Information

RF-LAMBDA USA www.rflambda.com

Sales: [email protected] Technical : s[email protected]

Wide Band EMC Benchtop Power Amplifier 2GHz ~ 18GHz

REMC0218GE

Rev 1. 06-10-2020

EMC Equipment User Manual

Front Panel

Rear Panel

ON/OFF switch

Power Indicator

Alarm Indicator

Keypad

Gain Adjustment Knob

RF Output

RF Input

Instrument AC power supply switch

Fuse Holder

Main AC connector

GND connector

USER CONTROL, D-SUB Connector

low-voltage (3.3V) TTL control signals.

See page below for more information.

USB Port (upon request)

LAN Port (upon request)

RF-LAMBDA USA www.rflambda.com

Sales: [email protected] Technical : s[email protected]

Wide Band EMC Benchtop Power Amplifier 2GHz ~ 18GHz

REMC0218GE

Rev 1. 06-10-2020

Self Calibration Screen

Instrument Protection Alarms

The front panel LCD screen will display the error code or error message when instrument self protection is

triggered. Front panel alarm indicator will light up.

To eliminate the error code, press “RESET” on front panel keypad to reboot the instrument and clear the alarms.

If error code can not be eliminated after reboot, please contact [email protected]

Calibration is may be recommended

“[1] Calibrate” to execute instrument self calibration

process.

“[2] Reset” to reboot the instrument.

*Please turn OFF RF input power, and terminate the RF

output port while applying calibration function

Switching On Instrument

Please follow the instructions on the front panel LCD screen after switching on the power.

Press “1” on keypad to continue.

Front Panel LCD Screen Display

RF-LAMBDA USA www.rflambda.com

Sales: [email protected] Technical : s[email protected]

Wide Band EMC Benchtop Power Amplifier 2GHz ~ 18GHz

REMC0218GE

Rev 1. 06-10-2020

Instrument temperature

RF output attenuation (change with adjustment knob)

RF input signal center frequency

Instrument RF output power

Switches On or Off for instrument RF output port

Indicates instrument RF output status. It will display:

Output is Ready to Turn on or RF Output is ON

Press “Menu” on keypad to enter instrument functions

selection menu

Instrument Function Selection Page

Instrument Status Display Page

To enter this function selection page, press “Menu” on front

panel keypad while the instrument is showing the status page.

Press the corresponding number on front panel keypad to

select:

“[1] Calibrate”calibrates the instruments.

“[2] Frequency” enters RF input signal center frequency.

“[3] RF ON/OFF” switches the RF output port on or off.

“[4] Reset” Restarts the instrument (Turns RF output off)

“[5] Status” enters instrument status display page.

“[6] Product Info” displays product part number and serial

number

All action functions will ask for confirming execution when selected from function selection menu.

User can set a constant gain for the unit. Equipment will

automatically adjust the gain at certain frequency

RF-LAMBDA USA www.rflambda.com

Sales: [email protected] Technical : s[email protected]

Wide Band EMC Benchtop Power Amplifier 2GHz ~ 18GHz

REMC0218GE

Rev 1. 06-10-2020

Pin #

Name

Function

Initial State

Description

Applied

Reset

Control

Resets PA when logic LOW is applied and released

Yes

Driver Disable

Control

LOW

Appling logic HIGH disables driver of amplifiers

Yes

Drain Disable

Control

LOW

Applying logic HIGH disables drain of amplifiers

Yes

RF IN Over

Indicator

LOW

Pin will be latched to logic HIGH when input signal is

over limit

Temp Over

Indicator

LOW

Pin will be latched to logic HIGH when amplifier is

driven over temperature

Yes

Current Over

Indicator

LOW

Pin will be latched to logic HIGH when drain current

limit is reached

Yes

ID Imbalance

Indicator

LOW

Pin will be latched to logic HIGH when an imbalance

in the drain current of the combining branches occurs

Yes

PA input

power

Indicator

PA input power is represented by voltage

PA output

power

Indicator

PA output power is represented by voltage

PA output

reflection

power

Indicator

PA output reflection power is represented by voltage

VSWR

Indicator

LOW

Pin will be latched to logic HIGH when output

reflection is over limit

+5V

Power Supply

+5V

+5V DC is supplied for reference

Yes

GND

Ground

GND

Ground

Yes

GND

Ground

GND

Ground

Yes

User Control Connector on Rear Panel

HIGH/LOW voltages are standard TTL signals:

0.0V-0.8V = LOW

2V-5V = HIGH

RF-LAMBDA USA www.rflambda.com

Sales: [email protected] Technical : s[email protected]

Wide Band EMC Benchtop Power Amplifier 2GHz ~ 18GHz

REMC0218GE

Rev 1. 06-10-2020

Important Notice

Amplifier Outline Drawing:

All Dimensions in mm [inches]

The information contained herein is believed to be reliable. RF-Lambda makes no warranties regarding the information contained herein.

RF-Lambda assumes no responsibility or liability whatsoever for any of the information contained herein. RF-Lambda assumes no responsibility

or liability whatsoever for the use of the information contained herein. The information contained herein is provided "AS IS, WHERE IS" and

with all faults, and the entire risk associated with such information is entirely with the user. All information contained herein is subject to

change without notice. Customers should obtain and verify the latest relevant information before placing orders for RF-Lambda products. The

information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or

any other intellectual property rights, whether with regard to such information itself or anything described by such information.

RF-Lambda products are not warranted or authorized for use as critical components in medical, life-saving, or life sustaining applications, or

other applications where a failure would reasonably be expected to cause severe personal injury or death.

506.94 [19.958]

25.75 [1.014]

46.11 [1.815]

482.6 [19.000]

465 [18.307]

133.2 [5.244]

11 [0.433]

7 [0.276]

447 [17.598]

436.8 [17.197]

PN:REMC18G40GM

Freq:18-40GHz

Table des matières

Autres manuels RF-Lambda Amplificateur

RF-Lambda

RF-Lambda REMC26G40GD Manuel utilisateur

RF-Lambda

RF-Lambda RAMP02G06GC Manuel utilisateur

RF-Lambda

RF-Lambda REMC18G26GC Manuel utilisateur

RF-Lambda

RF-Lambda REMC26G40GL Manuel utilisateur

RF-Lambda

RF-Lambda REMC18G40GC Manuel utilisateur

RF-Lambda

RF-Lambda REMC18G40GC2 Manuel utilisateur

RF-Lambda

RF-Lambda REMC27G32GD Manuel utilisateur

RF-Lambda

RF-Lambda REMC18G26GG Manuel utilisateur

RF-Lambda

RF-Lambda REMC27G34GB Manuel utilisateur

RF-Lambda

RF-Lambda REMC26G40GF Manuel utilisateur

RF-Lambda

RF-Lambda REMC0506GF Manuel utilisateur

RF-Lambda

RF-Lambda REMC06G18GD Manuel utilisateur

RF-Lambda

RF-Lambda RAMP06G18GC Manuel utilisateur

RF-Lambda

RF-Lambda REMC18G40GM Manuel utilisateur

RF-Lambda

RF-Lambda REMC12G17GD Manuel utilisateur

RF-Lambda

RF-Lambda REMC18G40GN Manuel utilisateur

RF-Lambda

RF-Lambda REMC0218GD Manuel utilisateur

RF-Lambda

RF-Lambda REMC0M3GW100 Manuel utilisateur

RF-Lambda

RF-Lambda REMC18G26GF Manuel utilisateur

RF-Lambda

RF-Lambda REMC18G40GC Manuel utilisateur

RF-Lambda

RF-Lambda RAMP06G18GF Manuel utilisateur

RF-Lambda

RF-Lambda RFLUPA0618GB Manuel utilisateur

RF-Lambda

RF-Lambda REMC18G23GD Manuel utilisateur

RF-Lambda

RF-Lambda REMC18G40GD Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur