Response QC 3674 Manuel technique
Installation and Operating Instructions
These instructions should be retained in a safe place for future reference.
2
CONTENTS
1. PLANNING YOUR LAYOUT (3)
2. KIT CONTENTS (5)
3. INSTALLATION (8)
4. CAMERA SETUP (9)
5. ABOUT DIGITAL WIRELESS TECHNOLOGY (12)
6. PRODUCT SPECIFICATION (13)
3
PLANNING YOUR LAYOUT:
SAFETY AND INSTALLATION TIPS:
DVR
• keep away from heat sources and high temperature places
• Avoid direct sunlight
• Avoid humid places
• avoid vibration
• Install in a ventilated environment
• do not replace the supplied 2GB memory card with a greater capacity(the unit may
fail to operate properly).
TV/Monitor
Receiver
DVR Front Door
Camera 2
Camera 1
Max 5m
Max 5m Max 5m
Max 5m
Ensure the distance from camera to power
outlet does not exceed the length of the
camera power adapter cable
15mm diameter
cable hole
(to allow camera
cable and connector
to pass through)
4
Camera(s) and DVR
NIGHT VISION:
Do not attempt to open the units with the power adaptor plug connected to avoid any risk
of personal injury.
When installing CCTV camera(s), always foloow manufacturer's advice when using
power tools, steps, ladders, etc. and wear suitable protective equipment (e.g. safety
goggles)when drilling holes. Before drilling holes through walls check for hidden
electricity cables and water pipes. The use of cable/pipe detector is advisable.
It is also advisable to avoid exposing any cameras to extreme weather conditions (e.g,
under a gutter which is prone to any water leaks). When installing any cameras with this
unit, it is advisable to use cable conduit to protect any video/power extension cables
from being exposed externally and to prevent/reduce the chances of the cables being
tampered with. After drilling any hole though an external wall for a cable, ensure the hole
is sealed up around the cable using a sealant to prevent drafts.
To prevent a re or electrical shock hazard, do not attempt to open the housing while
the unit is exposed to rain, water or wet conditions. There are no user serviceable
parts inside. Refer servicing to qualified service personnel. Avoid pointing the
camera(s) directly at the sun or any bushes, tree branches or moving objects that might
unnecessary cause the DVR to record due to winds for example. System also provides
"Masking" function, user may screen out motion detection area in parts of the picture
which motion detection is not required.
The camera has built-in infra-red LEDs to allow you to view at night for 24hrs
surveillance. The LEDs will automatically activate at night and the picture viewed will turn
to black and whit. The night viewing range is up to 7m.
5
x Digital Wireless Camera
A
B
x 5V/1A Power Adapter
C
x Camera Stand
D
x )L[LQJ3DFN
E
x Camera Antenna
F
x Manual
Tools Required:
Electric drill
5mm masonry drill bit
15mm masonry drill bit
No. 2 Philips screwdriver
KIT CONTENTS
6
AB
Digital Wireless Camera
C
5V/1A Power Adapter for
Camera and Receiver
D
)L[LQJ3DFN
Camera Stand
EF
Camera Antenna Manual
Digital Wireless Colour Camera
Recordable CCTV Kit
Installation and Operating Instructions
YOUR HELPLINE 0844 736 9149
www.friedland.co.uk
Lines open Monday to Friday 9.00am to 5.00pm. Calls charged at local rates.
These instructions should be retained in a safe place for future reference.
7
Setting the Camera Channel
Pairing the Camera to Receiver (Optional)
The wireless monitor support up to 4 wireless cameras. Follow the step below to set or
change the monitor channel of the camera. If you are adding another camera to link with the
supplied monitor in this kit, then ensure its channel is set to a different channel to the existing
camera(s).
Follow the steps in CAMERA SETUP section to set or change the channel of the camera. If
you are adding another camera to link with the supplied receiver in this kit, then ensure its
channel is set to a different channel to the existing camera(s).
Pairing Key
INSTALLATION
8
Attach Stand to Mounting Surface
A.Secure camera stand on the wall
B. Loosen up the Thumb screw
C.Adjust proper view angle then secure the joint with T-bolt.
C
B
CAMERA INSTALLATION
9
Select CAMERA SETUP, press MENU key once to enter sub-menu.
CAMERA SETUP
Use▼▲to select the camera to set up (1-4).
Use◄►to select [PAIRING] [BRIGHTNESS] [CAMERA ON/OFF]
10
Camera Pairing
With PAIRING section highlighted, press MENU key once to begin camera pairing (pair
LED on camera will blink once and following with LED blinking continuously indicating
data transmission in process.
System will conrm pairing process is successful with "PAIRED" displaying on screen.
System will indicate pairing process failed with "PAIRING FAIL" displaying on screen.
Press ESC to return to main menu.
With BRIGHTNESS section highlighted, use ▼▲ to adjust camera brightness.
Press ESC to return to main menu.
Camera Brightness Adjustment
Table des matières
Autres manuels Response caméscope
Manuels caméscope populaires d'autres marques
Panasonic
Panasonic AG-HMC152EN Manuel utilisateur
Insignia
Insignia NS-DCC5HB09 - Camcorder - 720p Manuel utilisateur
MYDLINK
MYDLINK DCS-6100LH Manuel utilisateur
Sony
Sony video Hi8 Handycam CCD-TR555 Manuel utilisateur
SECURECOM
SECURECOM V-5014B Manuel utilisateur
Panasonic
Panasonic HDC-SD100 Manuel utilisateur
