ReSound Phone Clip+ Manuel utilisateur
USER GUIDE
Phone Clip+
400227244-US-13.08-Rev.A.indd 1 19-08-2013 13:46:31
2
Welcome
Congratulations on your purchase of a Phone Clip+.
Phone Clip+ will allow you to connect your wireless compatible
hearing instruments to Bluetooth-enabled mobile phones. This
enables clear and hassle-free phone connectivity, whether you
are at home, in the office or on the move.
The Phone Clip+ also doubles as a basic remote control making
it possible for you to adjust the volume of your hearing instru-
ments and toggle through programs, when you are not talking
on the phone.
You can also choose to mute your hearing instrument micro-
phone to shut out environmental sound while you are talking on
the phone or when you are using the Phone Clip+ as a remote
control (function available on selected models only).
Please read this manual carefully to fully benefit from the Phone
Clip+. Ask your hearing healthcare professional if you have any
questions.
For your safety, carefully read the chapter Important Information,
on pages 25-31.
FCC ID: X26BTB-2
400227244-US-13.08-Rev.A.indd 2 19-08-2013 13:46:31
3
Statement:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harm-
ful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for
help.
400227244-US-13.08-Rev.A.indd 3 19-08-2013 13:46:31
4
Changes or modifications can void the user’s authority to oper-
ate the equipment.
Intended use
Phone Clip+ is intended to enable wireless hearing instrument
users to better follow phone conversations. The essential perfor-
mance of the Phone Clip+ is to transfer signals between a phone
with Bluetooth capabilities and compatible wireless hearing
instruments.
When not used for phone conversations the Phone Clip+ can
also be used as a basic remote control enabling volume adjust-
ment, program changes and hearing instrument microphone
mute* functionality.
List of countries
Products are intended for use in countries within European
Economic Area as well as Switzerland.
*Functionality available in some hearing aids
400227244-US-13.08-Rev.A.indd 4 19-08-2013 13:46:31
5
National restrictions:
Norway: You are not allowed to operate the equipment within 20
km of the centre of Ny Ålesund.
This product is in compliance with the following regulatory
standards:
In EU: The device conforms to the Essential Requirements ac-
cording to - Annex I of Council Directive 93/42/EEC for medical
devices (MDD) and essential requirements and other relevant
provisions of Directive 1999/5/EC (R&TTE). The declaration of
conformity may be consulted at www.resound.com
In US: FCC CFR 47 Part 15, subpart C, section 15.247 and
15.249.
Other identified applicable international regulatory requirements
in countries outside EU and US. Please refer to local country
requirements for these areas.
The product is categorized as receiver category 2 according to
EN 300 440.
iC: 6941C-BTB2
This Class B digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
400227244-US-13.08-Rev.A.indd 5 19-08-2013 13:46:31
6
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
In JP:
This device has been granted a designation number by Ministry
of Internal Affairs and Communications under „Ordinance con-
cerning Technical Regulations Conformity Certification etc. of
Specified Radio Equipment (特定無線設備の技術基準適合証明
等に関する規則)“ Article 2-1-xx “This device should not be modi-
fied (otherwise the granted designation number will be invalid)“
400227244-US-13.08-Rev.A.indd 6 19-08-2013 13:46:32
7
Contents
Description ........................................8
Getting Started ....................................10
Turning your Phone Clip+ ON and OFF..................11
Bluetooth Pairing...................................13
Phone operation ...................................16
Volume Control ....................................20
Operating Time ....................................21
Wearing Your Phone Clip+ ...........................21
Light indicators ....................................22
Introduction to Bluetooth ............................23
Important Information ...............................25
Technical specifications .............................32
Warranty .........................................33
Troubleshooting guide ..............................36
400227244-US-13.08-Rev.A.indd 7 19-08-2013 13:46:32
4
5
2
1 3
8
Description
1. ON/OFF switch
2. Call pick-up/hang-up button
3. Hearing instrument program toggle
4. Hearing instrument microphone mute button
5. Micro-USB for charging
400227244-US-13.08-Rev.A.indd 8 19-08-2013 13:46:33
910
7
8
6
9
6. Volume control
7. Microphone inlet
8. Mounting clip
9. Hearing instrument pairing button
10.Bluetooth pairing button
400227244-US-13.08-Rev.A.indd 9 19-08-2013 13:46:34
10
Getting Started
Charging the Battery
Before using your Phone Clip+, you
need to fully charge the rechargeable
battery.
To charge it, plug the charging cable
into the Phone Clip+ as shown in the
picture to the right.
Then plug the other end of the charg-
ing cable into a power outlet.
During the charging process, the light
indicator (LED) at the top of the Phone
Clip+ will show a solid red light.
When fully charged and still connected to the charger, the LED
will turn solid green interrupted by a red blink every 2 seconds.
Charging an empty battery typically takes around 3 hours. It is
safe to leave the charger connected overnight – the battery can-
not be overcharged.
• When charging your Phone Clip+ for the first time, leave it
to charge for at least 3 hours, even if the battery indicator
shows that the unit is fully charged (see section about “Light
indicators”).
400227244-US-13.08-Rev.A.indd 10 19-08-2013 13:46:35
Autres manuels pour Phone Clip+
2
Table des matières
