Renu Electronics FlexiPanels Basicc FP2 Series Manuel utilisateur

User Manual

FlexiPanels Basic®HMI

FP2 series HMI with I/Os

FlexiPanels®Basic HMI 
 
 
 
 
© Renu Electronics Pvt. Ltd. 
Page 2of 24 
 
 
 
Contents 
INTRODUCTION ...................................................................................................................................................4 
BEFORE YOU START..............................................................................................................................................4 
SAFETY PRECAUTIONS..........................................................................................................................................5 
PRODUCT OVERVIEW...........................................................................................................................................6 
INSTALLING FP2 WITH I/OS PRODUCTS .........................................................................................................................6 
PANEL GUIDELINES...................................................................................................................................................6 
PANEL CUTOUT DIMENSIONS ......................................................................................................................................6 
PRODUCT DIMENSIONS .............................................................................................................................................7 
MINIMUM CLEARANCES ............................................................................................................................................8 
MOUNTING FP2 WITH I/OS PRODUCTS.........................................................................................................................8 
CONNECTING POWER................................................................................................................................................8 
POWER RATING.......................................................................................................................................................8 
GROUNDING ...........................................................................................................................................................9 
PRODUCT SPECIFICATIONS...................................................................................................................................9 
PRODUCT NOMENCLATURE /ORDERING PART NUMBER ...................................................................................................9 
DISPLAY SPECIFICATIONS ................................................................................................................................... 10 
CPU, MEMORY AND POWER SUPPLY.......................................................................................................................... 10 
COMMUNICATION INTERFACES.................................................................................................................................. 11 
RS232 /RS485 PORT ............................................................................................................................................ 11 
YTYPE CABLE........................................................................................................................................................ 12 
ETHERNET PORT .................................................................................................................................................... 14 
USB DEVICE PORT ................................................................................................................................................. 15 
USB HOST PORT.................................................................................................................................................... 15 
SUPPORTED PLUGGABLE EXPANSION MODULES............................................................................................................. 16 
SUPPORTED PROTOCOLS.......................................................................................................................................... 20 
ACCESSORIES ..................................................................................................................................................... 21 

FlexiPanels®Basic HMI

Page 3of 24

PROGRAMMING CABLE (DOWNLOAD)......................................................................................................................... 21

COMMUNICATION CABLE ......................................................................................................................................... 21

DEFAULT PRODUCT SETTING ..................................................................................................................................... 22

ENVIRONMENTAL SPECIFICATIONS AND APPROVALS ....................................................................................................... 22

REVISION HISTORY............................................................................................................................................. 23

NOTES ............................................................................................................................................................... 24

FlexiPanels®Basic HMI

Page 4of 24

Introduction

FP2 series HMI with I/Os is suitable for simple applications. Available screen sizes are 4.3” WQVGA

and 7" WVGA Color TFT. These HMIs are powered by FlexiSoft® programming software. These

products also support the IEC61131-3 logic programming environment which gives a unique edge

to these products.

All the products are compliant to EMC directive 2014/30/EU and LVD directive 2014/35/EU and

suitable for installation in hazardous locations because they are listed for UL Class I Div. 2.

This user manual gives detailed information regarding the hardware specifications, operating

conditions, installation, mounting, and wiring. All the information published in this manual is

produced and governed by RENU Electronics Pvt. Ltd. and is protected by Indian Copyright Act.

Before you start

FlexiPanels®FP2 series HMI with I/Os products are general-purpose human machine

interface devices, suitable for a variety of simple applications across various industries.

However, RENU Electronics is not responsible or liable for any indirect or consequential

damage resulting from the use of this product.

The user should check and confirm the suitability of the product before using it in any

specific application.

The diagrams and examples in this manual are included for illustration purposes only.

RENU Electronics assumes no responsibility or liability regarding actual use based on

these diagrams or examples.

Reproduction of the contents of this manual, in any form (in part or whole), is strictly

prohibited.

Following table shows various symbols that may be used in this manual to provide

information regarding safety, precautions, and usage of the product:

WARNING: Indicates circumstances that may cause an explosion in a hazardous environment,

which may lead to injury or death, damage or economic loss

CAUTION: Indicates specific precautions to be taken by the user during installation, operation

and maintenance of the product

ATTENTION

ATTENTION: Indicates important information regarding the application and functions of the

product

FlexiPanels®Basic HMI

Page 5of 24

Safety Precautions

This section of the manual provides information that is critical regarding safety and therefore the

user is advised to go through the information in detail before installing the product. Users may

contact RENU Electronics technical support team at [email protected] for any

specific question(s) related to safety.

WARNING: EXPLOSION HAZARD

Do not disconnect equipment unless power has been removed or the area is known

to be nonhazardous.

The substitution of any component may impair suitability for Class I, Division 2.

Secure any external connections that mate to this equipment by using screws, sliding

latches, threaded connectors, or any other means provided with this product.

If this product contains batteries, it must only be changed in an area known to be

nonhazardous.

CAUTION: GENERAL PRECAUTIONS

Do not use this product for an emergency stop. A separate physical switch, outside

the product, must be used for any emergency stop operations.

Do not use the external power supply source that does not comply with the specified

power requirements of the product, it may cause malfunction or permanent damage

to the product.

Do not attempt to open, dismantle, or modify the product, doing so will void the

warranty.

This product is supplied as open-type equipment and it must be mounted within an

enclosure, suitably designed for specific environmental conditions.

When used in Class I, Division 2 hazardous location, the product must be mounted

in a suitable enclosure with a proper wiring method that complies with the governing

electrical codes.

The USB port is intended for temporary local programming purposes only and not

intended for permanent connection. If you connect or disconnect the USB cable with

power applied to this product or any other device on the USB network, an electrical

arc can occur, which could cause an explosion in hazardous location installations.

Make sure that connectors are securely tightened to properly seal the connections

against leaks.

Do not place the product in direct sunlight. Prolonged exposure to sunlight may

degrade the LCD and housing.

FlexiPanels®Basic HMI

Page 6of 24

Product Overview

This section of the manual provides an overview of series with I/Os products, its front and back

view, installation details, dimensional details, mounting method, and details.

Installing FP2 with I/Os products

FP2 series HMI with I/Os series products are designed for front panel mounting. Before installing

the products, the user should review the panel guidelines, panel cutout dimensions, product

dimensions, and minimum clearances.

Panel Guidelines

The panel must be at least 2mm (12gauges) so that it can provide the required support and

proper sealing against water and dust. The panel surface must be flat, without any imperfection,

to maintain the adequate seal and IP rating.

The maximum panel thickness allowed is 6mm (±0.2mm).

Panel Cutout Dimensions

The panel must be at least 2mm (12gauges) so that it can provide the required support and

proper sealing against.

Model

Height (mm)

Width (mm)

FP2043T-E

111

FP2043TN-E

111

FP2070T-E

127

175

FP2070TN-E

127

175

ATTENTION

ATTENTION: Panel cutout

Before making a panel cutout, disconnect all electrical power from the panel.

Make sure that area surrounding the panel cutout is clear.

Make sure that metal cutting does not enter any component already installed in the

panel.

FlexiPanels®Basic HMI

Page 7of 24

Product Dimensions

This section of the manual provides dimensional details of FP2 series HMI with I/Os products. All the

dimensions shown below are measured in mm.

FP2043-E

FP2070-E

FlexiPanels®Basic HMI

Page 8of 24

Minimum Clearances

Maintain clearance from enclosure walls, wires, and other adjacent devices. Keep 2” space on all sides

for adequate ventilation. Plan for adequate space around the product and inside the enclosure for

ventilation and cabling. Take into consideration the heat produced by other devices in the enclosure. The

ambient temperature around this product must be 0° to 50°C.

Mounting FP2 with I/Os Products

FP2 series HMI with I/Os products must be installed on the front panel, using the clamp accessories

shipped with the product. Before mounting, make sure that the sealing gasket is properly positioned. This

gasket forms a compression type seal. Do not use sealing compounds. Then, place the unit in the panel

cutout and tighten the mounting screws evenly (torque 0.4Nm) to maintain water and dust resistance.

ATTENTION

ATTENTION: Mounting FP2 series HMI with I/Os on Panel

Do not push the LCD display when pushing the unit into the panel as it may damage

the display.

Connecting Power

FP2 series HMI with I/Os requires a 24VDC isolated power supply. Follow the steps mentioned below to

connect the power:

Make sure that terminal is not connected to a power source

Secure the 24VDC power wires

Secure the functional earth ground wire to the functional earth ground terminal screw on the

terminal block

Apply 24VDC power to the terminal

Power Rating

Unit

Voltage

Current

Wattage

FP2043T-E

24VDC

130mA

3.12W

FP2043TN-E

24VDC

150mA

3.6W

FP2070T-E

24VDC

200mA

4.8W

FP2070TN-E

24VDC

230mA

5.52W

FlexiPanels®Basic HMI

Page 9of 24

Grounding

The optimum method for grounding electronic equipment is to ground it separately from other high-power

systems and to ground more than one unit of electronic equipment with a single-point ground. Following

marked terminal is provided with the unit for grounding:

Product Specifications

This section of the manual provides detailed specifications of FP2 series HMI with I/Os products, ordering

part numbers, operating conditions, environment, and approvals.

Product Nomenclature / Ordering Part Number

FP2 series HMI with I/Os has 2 models, depending on display size and each model has two variants,

based on Ethernet. Detail part number or ordering information is as follows:

Model

Description

FP2043T-E

2 Serial ports#(1 RS232, 1 RS485), 1 USB Device, 1 USB Host, 1 Pluggable I/O Module

FP2043TN-E

2 Serial ports#(1 RS232, 1 RS485), 1 USB Device, 1 USB Host, 1 Ethernet, 1 Pluggable

I/O Module

FP2070T-E

2 Serial ports (RS232 / RS485), 1 USB Device, 1 USB Host, 3 Pluggable I/O Modules

FP2070TN-E

2 Serial ports (RS232 / RS485), 1 USB Device, 1 USB Host, 1 Ethernet, 3 Pluggable I/O

Modules

[ #Note: FP2043-E support one DB9 port that supports RS232 and RS485 levels on different pins. “Y” type cable

can be used for separate RS232 and RS485 levels simultaneously.]

T: Touch Screen

FP2 XXX Tx- E

Series

Display Size

043: 4.3” WQVGA (480 x 272)

070: 7” WVGA (800 x 480)

Series

T: Touchscreen

N: Supports Ethernet

E: Supports Expansion

FlexiPanels®Basic HMI

Page 10 of 24

Display Specifications

FP2 with I/Os series products support high-quality color TFT display range.

Size: 4.3” WQVGA Color TFT with 4-wire analog resistive touch screen

Resolution: 480 x 272pixels

Brightness: 400cd/m2

Backlight life: 30,000Hrs.

Size: 7” WVGA Color TFT with 4-wire analog resistive touch screen

Resolution: 800 x 480pixels

Brightness: 350cd/m2

Backlight life: 30,000Hrs.

CPU, Memory and Power Supply

CPU: 32-bit RISC Processor

RAM: 16MB

User Application

8MB

Flash

16MB

Ladder Memory

2MB

Alarm Memory

1350 Alarms

Retentive Memory

8000Words

Keep Memory

1000Words

Data Log

4MB

Power supply:

24VDC(+20%, -15%)

RTC:

Built-in, Date & Time function

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Renu Electronics Équipement d'enregistrement

Renu Electronics

Renu Electronics FP4043TN-E Manuel utilisateur

Manuels Équipement d'enregistrement populaires d'autres marques

KV2 Audio

KV2 Audio 500 Series Manuel utilisateur

Robotics Technologies

Robotics Technologies microBus-Cam II Manuel utilisateur

Seca

Seca 460 Manuel utilisateur

Cognex

Cognex MVS-8000 Series Manuel utilisateur

Mect

Mect MPNC006 Series Manuel utilisateur

Bad Caf

Bad Caf THE LEASH Manuel utilisateur

Strymon

Strymon NIGHTSKY Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur

Tews Technologies

Tews Technologies TPMC465 Manuel utilisateur

Honeywell

Honeywell Excel 50 Manuel utilisateur

SeaLevel

SeaLevel COMM+8.LPCI Manuel utilisateur

Arturia

Arturia AUDIOFUSE STUDIO Manuel utilisateur

Rukra

Rukra RK-1240 Manuel utilisateur

Samson

Samson SCOM Manuel utilisateur

Dynacord

Dynacord DPS260 Manuel utilisateur

Nice

Nice Core Manuel utilisateur

Pyle Pro

Pyle Pro PSS8 Manuel utilisateur

RF-System

RF-System TinyGate Manuel d'utilisation et d'entretien