Remington PG6000 Manuel utilisateur

G6 Graphite Series

Personal Groomer

PG6000

I www.remington.co.uk

Visit uk.remington-europe.com/product-registration

You must register within 28 days of purchase.

3 mm

6 mm

9 mm

Thank you for buying your new Remington® product. Please read these instructions

carefully and keep them safe. Remove all packaging before use.

IMPORTANT SAFEGUARDS

• This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been supervised/instructed and

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be done by children

unless they are older than 8 and supervised. Keep the appliance and cable

out of reach of children under 8 years.

• The adaptor contains a transformer. Do not cut oﬀ the adaptor to replace it

with another plug, as this causes a hazardous situation.

E Suitable for use in a bath or shower.

• WARNING: Detach the shaver from the charging adapter before cleaning it

in water.

• Do not use the product with a damaged cord.

• WARNING: For recharging the battery, only use the charger supplied with

the appliance - type reference PA-0505U (UK).

• Always replace a damaged adaptor with one of the original type.

• The battery in this device is not replaceable.

• Do not use the appliance if it is damaged or malfunctions.

• Do not use attachments other than those we supply.

• This appliance should never be left unattended when plugged into a power outlet,

except when charging.

• Keep the power plug and cord away from heated surfaces.

• Do not plug or unplug the appliance with wet hands.

• Do not twist or kink the cable, or wrap it round the appliance.

• This appliance is not intended for commercial or salon use.

PARTS

1. On/O switch

2. Charging indicator light

3. Charging connector

4. Wide trimmer

5. Adjustable comb

6. Fixed guide combs

7. Precision trimmer

8. Nose, ear, eyebrow trimmer

9. Mini foil shaver

10. Deep cleansing brush head

11. Body hair trimmer

12. Body hair trimmer comb

13. Adaptor (not shown)

14. Storage pouch (not shown)

CHARGING YOUR APPLIANCE

Before using your trimmer for the rst time, charge for 4 hours.

1. Ensure the product is switched o.

2. Connect the charging adaptor to the product and then to the mains.

CHARGING INDICATOR LIGHT

Charge Level Indicator

Charging Blue LED will ash

Fully Charged Blue LED will light up continuously

Battery charge is low Red LED will ash

• Your trimmer cannot be overcharged. However, if it is not going to be used for an

extended period of time (2-3 months), unplug it from the mains and store.

• To preserve the life of your batteries, let them run out every 6 months then recharge

for 4 hours.

• On a full charge, your beard trimmer will run for up to 90 minutes of cordless usage.

ATTACHMENTS

TO FIT AND REMOVE ATTACHMENTS FIG. A

Ensure that the device is switched o before tting or removing attachments.

• To remove, rotate the attachment anti-clockwise until it unlocks and then lift it o.

• To t, place the desired attachment on top of the device and rotate the attachment

clockwise to lock it into place.

FITTING AND REMOVING FIXED GUIDE COMBS

To Fit

• Hook the front of the guide comb over the teeth of the wide trimmer.

• Press the back of the guide comb down until it clicks into place.

To Remove

• Lift the tab on the back of the guide comb upwards until it comes free from the wide

trimmer head.

FITTING AND REMOVING THE ADJUSTABLE COMB

• To t, line up the rails on the comb with the slots on the sides of the groomer and

slide the comb downwards onto the groomer.

• To adjust, press and hold the adjustment button on the back of the comb and slide

the comb up or down. Release the button to lock the comb at that position. The

length of cut is indicated by the scale on the side of the trimmer.

• To remove, press and hold the adjustment button and push the comb up and o the

groomer.

INSTRUCTIONS FOR USE

• Comb facial hair with a ne comb before you start trimming.

• Comb your hair in the direction that it grows so that the hairs are at their maximum

height and facing in the same direction.

• After trimming, lightly go over the trimmed areas with the foil to get a smooth clean

nish.

• Since all hairs do not grow in the same direction, you may want to try dierent

trimming positions (i.e. upwards, downwards or across) for better results.

• Hair should be dry and free from any waxes or lotions.

• If hair builds up during use, switch the unit o, remove any attachment in use and

clean any excess hair clippings from the attachment and groomer.

3DAY STUBBLE, AND BODY HAIR MAINTENANCE

Attachments

Wide trimmer with 1.5 mm xed comb

Body hair attachment

3-day stubble look:

Let your stubble grow to a length that is slightly longer than the look you are trying to

achieve.

1. Fit the 1.5 mm xed comb to the wide trimmer attachment.

2. Run your trimmer through your beard against the direction of hair growth.

3. Tidy the edges of the stubble using the precision trimmer attachment.

• For more control over the length of your stubble, you can use the adjustable comb

and trim your stubble down in increments starting at a longer length setting until

you get the desired look.

Body hair maintenance: Trimming to length

1. Fit the body hair attachment.

2. Body hair can be trimmed to 3 dierent lengths (3, 6 and 9 mm). Select the desired

length by sliding the comb into one of the three slots on the side of the attachment.

3. Place the at side of the attachment against the skin.

4. Slowly slide the trimmer through the hair in the direction of hair growth.

5. Use slow, well-controlled movements.

Body hair maintenance: Removal

1. Remove the comb from the body hair attachment and go over the areas where you

want to remove the body hair.

2. Stretch the skin with your free hand to make the hairs stand upright.

3. Use light pressure and shave against the direction of hair growth.

HAIR CLIPPING

Attachments

Wide trimmer with adjustable comb

Step 1: Nape of the neck

1. Fit the wide trimmer and adjustable comb.

2. Set the adjustable comb to 4 mm or 6 mm.

3. Hold the clipper with the blade teeth pointing upwards. Begin starting at the centre

of the head at the base of the neck.

4. Slowly lift the clipper, working upwards and outwards through the hair, trimming

just a little at a time.

Step 2: Back of the head

• With the comb set at 12 mm or 18 mm, cut the hair at the back of the head.

Step 3: Side of the head

1. Adjust the comb to a shorter length setting for the areas around the ears.

2. Increase the length setting on the adjustable comb to gradually transition the length

of hair on the side of the head to the longer hair on the top of the head.

Step 4: Top of the head

1. Adjust the comb to the longer length settings (up to 20 mm) then cut the hair on top

of the head against the direction in which the hair normally grows.

2. Always work from the back of the head.

Trim the sideburns

• To trim the sideburns, adjust the comb to the desired length setting, or use one of

the xed guide combs.

SHORT/LONG BEARD TRIMMING

Attachments

Wide trimmer with adjustable comb

Precision trimmer

1. Fit the wide trimmer and adjustable comb.

2. Set the adjustable comb to the desired length.

3. Start trimming under the chin following the line of the jaw.

4. Work upwards towards the ear and upper beard line.

5. Tidy the beard edges using the precision trimmer attachment.

CONTOUR EDGING AND CLOSE HAIR CUTTING

Attachments

Wide trimmer

Contour edging:

1. Hold the device with the cutting blade (teeth) facing you and at 90 degrees to the

skin.

2. Start with the edge of the beard/moustache line and, with the blade resting lightly

against the skin, use slow controlled movements to create contoured lines.

Close hair cutting:

1. Use the ngers of one hand to lift the hair at the base of your head up o your neck.

2. Your index nger should be covering the roots of the hairs you are lifting to prevent

them from being accidentally cut.

3. Hold the trimmer to the base of your neck with the blade facing up. Move the

trimmer up the neck until it touches your index nger which is protecting the hair

roots.

4. Move your trimmer slowly and keep the hair roots at the base of your head out of the

way of the trimmer.

DETAILED NOSE, EYEBROW AND EAR HAIR TRIMMING

Attachments

Nose, ear and eyebrow trimmer

Nose and ear:

1. Fit the nose, ear and eyebrow trimmer.

2. Insert the attachment gently into the nostril or ear.

3. Gently move the attachment in and out while rotating the body of the groomer at

the same time.

• Don’t insert the attachment more than 6 mm.

• Wash the attachment after each use.

Eyebrow:

1. Carefully guide the attachment to remove any stray or longer hairs from the

eyebrow.

2. To completely remove hairs, let the attachment touch the skin then move over the

desired area.

MICRO STUBBLE AND PRECISION TRIMMING

Attachments

Precision trimmer

Micro stubble:

The precision trimmer attachment has Trim Shave Technology which trims hair down to

0.2 mm to leave a micro stubble nish.

1. Fit the precision trimmer.

2. Hold the attachment so that the guide on the lower edge of the blade contacts the

skin (the same way you would hold a wet razor). The guide on the lower edge of the

blade helps to stretch the skin during trimming.

3. Use motions similar to wet shaving.

Precision trimming:

1. Hold the precision trimmer attachment perpendicular to the skin.

2. Move it towards or away from the beard hair to achieve the desired result. Use gentle

pressure and controlled movements.

DEEP CLEANSING BRUSH HEAD

Attachments

Deep cleansing brush head

1. Moisten the brush bristles by running under water. NOTE: DO NOT use the brush

head whilst completely dry as this can cause skin irritation.

2. Dampen your skin with water and apply face wash onto your skin. Alternatively,

apply your face wash directly onto the brush.

3. We recommend cleansing with the Deep Cleansing brush in 3 sections:

• T-Zone (1), Right side (2) and Left side (3).

4. Switch on using the On/O button.

5. Place the facial brush directly onto your skin.

6. Gently glide the brush over the skin and beard in circular motions avoiding the

delicate eye area.

NOTE: Try to avoid applying too much pressure with the brush when directly on the skin.

CLEAN SHAVEN EDGING

Attachments

Mini Foil Shaver

1. Hold the trimmer so the mini foil shaver gently touches your face.

2. Use short, well-controlled movements to shave around your beard moustache. Use

your free hand to stretch your skin. This encourages the hair to stand upright,

making it easier to shave.

• Note: The mini foil shaver was designed to shave the detail areas around your beard/

moustache/sideburns. It was not designed to shave your entire face. For a close

comfortable shave, guaranteed, use one of Remington’s electric shavers.

CARE FOR YOUR GROOMER

Care for your product to ensure a long lasting performance. We recommend that you

clean your groomer after each use.

AFTER EACH USE

• Brush any accumulated hairs from the groomer and attachment heads.

• The easiest and most hygienic way to clean the groomer is by detaching the head

from the groomer body and rinsing the head with warm water.

• The groomer body should not be rinsed.

• Place one or two drops of cutter oil or sewing machine oil on the blades.

• Turn the clipper on to distribute the oil evenly, wipe o any excess oil.

BATTERY REMOVAL

We strongly recommend that a professional removes the rechargeable battery. Parts of

the shaver case, and tools have sharp edges and may cause injury if not handled

correctly.

• The rechargeable battery must be removed from the appliance before it is scrapped.

• Disconnect the charging adapter before removing the battery.

1. Ensure the device is discharged of all power. To do this, switch it on and allow it to

run until it stops.

2. Using a suitable tool, carefully pry apart the front and rear halves of the case at the

joint line.

3. Remove the two screws that hold the transparent inner case to the back half of the

outer case.

4. Lift out the inner case.

5. Pull the black motor holder o the transparent case.

6. Slide the circuit board and battery out of the transparent inner case.

7. Cut the tabs holding the battery to the circuit board.

• Used batteries must be removed from the appliance and disposed of at an

appropriate ocial recycling/collection point.

• Do not attempt to operate the shaver once you have opened it.

RECYCLING

WTo avoid environmental and health problems due to hazardous

substances, appliances and rechargeable and non-rechargeable

batteries marked with one of these symbols must not be disposed of

with unsorted municipal waste. Always dispose of electrical and

electronic products and, where applicable, rechargeable and

non-rechargeable batteries, at an appropriate ocial recycling/

collection point.

SERVICE AND GUARANTEE

Defects aecting product functionality appearing within the

guarantee period will be corrected by replacement or repair at our

option provided the product is used and maintained in accordance

with the instructions. Your statutory rights are not aected.

This warranty shall not be valid where it is contrary to U.S. and other

applicable laws, or where the warranty would be prohibited under

any economic sanctions, export control laws, embargos, or other restrictive trade

measures enforced by the United States or other applicable jurisdictions. This includes,

without limitation, any warranty claims implicating parties from, or otherwise located in,

Cuba, Iran, North Korea, Syria and the Crimea region.

To claim an extra 1 year guarantee, register your product online within 28 days of

purchase.

Consumables are guaranteed only for their recommended lifecycle. Replacement/spare

parts* are excluded and are only covered by a 1 year warranty.

*Examples include, but are not limited to, adaptors, haircare attachments, grooming accessories, etc.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Remington Tondeuse

Remington

Remington Axcess 117535-01A Manuel utilisateur

Remington

Remington RM5124TH Manuel utilisateur

Remington

Remington RM1822BH Manuel utilisateur

Remington

Remington RM40BST Manuel utilisateur

Remington

Remington WPG-4021 Manuel utilisateur

Remington

Remington Axcess trimmer RM3017HP Manuel utilisateur

Remington

Remington NE3700AU Manuel utilisateur

Remington

Remington REVEAL MPT4000C Manuel utilisateur

Remington

Remington Axcess trimmer RM3017HP Manuel utilisateur

Remington

Remington VPG-6530 Manuel utilisateur

Remington

Remington ST3010A Manuel utilisateur

Remington

Remington RM4522TH Manuel utilisateur

Remington

Remington HT5024PHT Manuel utilisateur

Remington

Remington QUICKGROOM BHT6450AU Manuel utilisateur

Remington

Remington Smooth & Silky WPG-250 Manuel utilisateur

Remington

Remington RM115ST Manuel utilisateur

Remington

Remington HT4522T Manuel utilisateur

Remington

Remington RM2700 Manuel utilisateur

Remington

Remington PG-525 Manuel utilisateur

Remington

Remington RM4020 Manuel utilisateur

Remington

Remington G5 Graphite Series Manuel utilisateur

Remington

Remington Smooth & Silky WPG4010 Manuel utilisateur

Remington

Remington G2 Graphite Series Manuel utilisateur

Remington

Remington MB7000AU Manuel utilisateur

Manuels Tondeuse populaires d'autres marques

MTD

MTD HT 51 E Manuel utilisateur

McCulloch

McCulloch T22 LS Manuel utilisateur

COCKRAFT

COCKRAFT PRO HL36-S Manuel utilisateur

Grizzly

Grizzly CT 1800 Li Manuel utilisateur

Peco

Peco Z Trimmer ZT-3000 Manuel utilisateur

Solo

Solo 116 Manuel utilisateur

Stiga

Stiga ST 1200 Manuel utilisateur

Echo

Echo GT-225 - 10-09 Manuel utilisateur

RedMax

RedMax BT17 Manuel utilisateur

GreenWorks

GreenWorks STA806 Manuel utilisateur

Parkside

Parkside PHSL 900 A3 Manuel utilisateur

Gardeo

Gardeo PRO GPTHT2560 Manuel utilisateur

Park

Park DT-810870 Manuel utilisateur

Worx

Worx WG209 Manuel utilisateur

Gardenline

Gardenline 43671/HTKS26 Manuel utilisateur

Makita

Makita 3710 Manuel utilisateur

Champion

Champion 100683 Manuel utilisateur

Stihl

Stihl FS 311 Manuel utilisateur