Reliable 2700SZ Manuel utilisateur

INDUSTRIAL SEWING MACHINE INSTRUCTION MANUAL

2700SZ

1. Do not place your foot on the pedal when connecting to the power source

2. Installation and initial trial-run must be done by a skilled perfessional

3. Open control box or motor cover under electrical power is not permitted

4. Ensure the eathing system is in working order

5. When doing the following, the machine has to be disconnected from the power supply:

a. Threading the machine, replacing needle, bottom thread

b. Installing, dismantling or repairing

c. When the machine is being moved, turned over, or adjusted

1. Do not work in a damp or wet environment

2. Voltage requirements - 210V~240V

3. Must be adequately grounded for safety

4. Do not work at high temperature

5. Do not run motor and control system near ferromagnetic or high radience area.

Environmental Requirements

General Safety Instructions

The servomotor is composed of control system

and motor.

A. Control system includes control box and

speed controller

Direct Drive Motor & Components

This control system features quick start, quick stop, accurate needle

positioning and speed settings. The motor also features a self-protection

system against lower voltage, over current and over heating.

Voltage 220V 2phase

Frequency 50~60HZ

Speed 200-6500RPM

Motor torque 400≤2N.M 500≤3N.M

Specifications

Direct Drive Installation

Install control box and speed controller as gure below.

Using screws, mount the control box and speed controller onto sewing table.

Direct Drive Motor Installation:

1. Rotal Installation

a) Remove the hand wheel, belt cover and wind blade on the sewing machine

b) Install the Fan blade (gure 1) and rotor (gure 2) into the shaft of sewing

machine as seen above. Secure parts into place with washer (gure 3) and

screws (gure 4 & 5).

2. Motor Installation

Using a special plastic positioning jib (gure 6), install into sewing machine over the

rotor (gure 2) directed then secure with screws (gure 8). Screw down to be able

to easily pull out the positioning sleeve. (Note: Use caution when installing and pay

attention to the magnet suction, as this can cause injury to hand).

3. Check Rotar & Stator Installation

a) Remove rubber hole stopper (gure 9).

b) Check the plane of the rotor and ensure the stator is at, surface should not

exceed 1.5mm (See section gure A). If area is more than 1.5mm, remove the

motor and the rotor with gasket to adjust (gure 11).

c) Adjust to t back rubber hole stopper. (Note: The distance between the two

should be as small as possible. If more than 1.5mm, motor torque will

decrease).

Figure A

4. Hand Wheel Installation

a) Turn the sewing hand wheel by hand ，make the needle stop at the highest level

b) Put the hand wheel in the rotor, and mark the calibration line of the motor housing with the

scale 5 (Figure B).

1.5mm- 2.5mm (Figure C). (Note: Overlock machines will have three little strips (Figure D).

Figure B Figure C Figure D

The serial

number Parameter Description Adjusting range

The factory

reset

settings

1 P-01 Maximum

Speed lock 200-6500RPM 4500

2 P-02 Direction of

rotation

0 is reverse

turn needle

1 is clockwise

turn 1

Old flat

seam motor

change to 2

Entering the Parameter Menu:

1. Ensure the sewing machine is on

2. Press the “P” key, then press the “+” key. The screen will display “P-00”

3. Press the “+” key again to change the “P-00” to “P-02” (P-01 and P-02 are

speed and motor direction patemeter)

4. Press “P” key again to enter into parameters - screen will display “!”

5. Press “+” or “-” to scroll through the parameters list

6. Press the “S” key to save the desired parameter and exit the parameter screen

Restore Factory Settings:

To restore the factory settings, press the “P” key and the “+” key. The screen will

display “P-00” , then press and hold the “S” key for 3 seconds.

Parameter Settings:

or 3

3 P-03 The needle

angle 6-18°12°

4 P-04 Start sewing

speed 200-800 250

5 P-05 Speed up

And slow 2000-4000 3500

6 P-06 Set the seam 0-999 0

P-07

P-08

P-09

10 P-10 Automatic

Clearance run

Press the S key when change

0 to 1 0

11 P-11 Presser foot ascend

starting time 0-2000ms 0

12 P-12

Ascension presser

foot protection

time

1-120s 4s

13 P-13

Old section flat

sewing machine

selection

Motor option 1 is old section

flat sewing machine 0

0 is ordinary

sewing

machine

14 P-14 Maximum current

limiting 50-1000 280

15 P-15

Whether to detect

the up needle

position

1:detecting needle

0:no detection 1

The serial

number Error code Description Possible Fixes

1 Er01

Can’t find the needle

position

1. The hand wheel is not closed, clearance within 2.5 mm

2. Nine plug contact not connecting

3. Motor holzer bad, replace the motor

4. Hand wheel magnet error

2 Er02

Not detected boot

speed regulator

1. Speed control device is not plugged in/ no power

2. Speed wire is broken or has poor contact

3 Er03 Motor holzer or

phase error

1. Nine hole plug contact is poor

2. Check for motor damage

3. Holzer is bad

4 Er04 Locked-rotor

protection

1. Motor overload

2. Poor connection of motor and controller

3. Motor error

5 Er05

Hardware

over-current

protection

1. The motor overload

2. Line contact is bad or broken

3. Main board is bad

Common Faults & Treatments

6 Er07

Serial port

communication

timeout error

Display to the system board signal is bad or board is bad

Screen without

electricity

Switch with

electricity

1. Main board is broken

2. The display screen adn the main board connection line

contact is bad

Table des matières

Autres manuels Reliable Machine à coudre

Reliable

Reliable MSK-335B Manuel utilisateur

Reliable

Reliable 4400SW Manuel utilisateur

Reliable

Reliable MSK-555 Manuel utilisateur

Reliable

Reliable MSK-588 Manuel utilisateur

Reliable

Reliable 7200SB Manuel utilisateur

Reliable

Reliable MSK-1541S Manuel utilisateur

Reliable

Reliable MSK-8900M Manuel utilisateur

Reliable

Reliable 2400SZ Manuel utilisateur

Reliable

Reliable MSK-1341B Manuel utilisateur

Reliable

Reliable Dreamstitcher Portabl 787 Manuel utilisateur

Reliable

Reliable MAESTRO 600SB Manuel utilisateur

Reliable

Reliable MSK-8900M Manuel utilisateur

Reliable

Reliable MSK-146B Manuel utilisateur

Reliable

Reliable 5600TW Manuel d'utilisation et d'entretien

Reliable

Reliable 7200DB Manuel utilisateur

Reliable

Reliable Barracuda 2000U-33 Manuel utilisateur

Reliable

Reliable MSK-146BL-4 Manuel utilisateur

Reliable

Reliable MSK-146B Manuel utilisateur

Reliable

Reliable MSK-755H Manuel utilisateur

Reliable

Reliable MSK-441 Manuel utilisateur

Reliable

Reliable 7100DB Manuel utilisateur

Reliable

Reliable Barracuda 2000U-33 Manuel utilisateur

Reliable

Reliable MSK-3314N-CF7-40H Manuel utilisateur

Reliable

Reliable 7000FE Manuel utilisateur

Manuels Machine à coudre populaires d'autres marques

Riccar

Riccar RL634DE Manuel utilisateur

Singer

Singer 2517 Manuel utilisateur

Pfaff

Pfaff 3307-1 SERIES Manuel utilisateur

Janome

Janome Quilt Maker Pro 18 VERSA Manuel utilisateur

Siruba

Siruba C007JP Manuel utilisateur

Husqvarna Viking

Husqvarna Viking Designer SE Manuel utilisateur

Singer

Singer 148-5 Manuel utilisateur

IKEA

IKEA SY Manuel utilisateur

Pfaff

Pfaff 571 Manuel utilisateur

Singer

Singer 15-91 Manuel utilisateur

Brother

Brother BB370 Manuel utilisateur

Pegasus

Pegasus WT100 Series Manuel utilisateur

Pfaff

Pfaff 937 Manuel utilisateur

Singer

Singer 6038 Manuel utilisateur

Singer

Singer 413K Manuel utilisateur

Pfaff

Pfaff 1471 E1 Manuel utilisateur

Kenmore

Kenmore 16677 - Serger Sewing Machine Manuel utilisateur

HIGHLEAD

HIGHLEAD GC2008-M Manuel utilisateur