ReelCraft G 3050 Manuel utilisateur

Operating Instructions

Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725

Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605

Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com

Rev: 12/2018

G 3050 G 3050 Y G 3050 N GS3050

Static Discharge Reels

Model Number:

INSTALLATION

Be sure reel base is securely grounded to mounting surface. Check for continuity following installation. On painted surfaces,

remove paint at bolt location, use external tooth lockwashers or run ground wire from reel base to grounded object. Failure to

ground will prevent reel from performing its intended function and could result in personal injury.

CAUTION

Mount reel to grounded, metal surface using four holes in mounting base. To minimize wear on cable and cable guide, reel

should be mounted in direct line with work so that cable is pulled out as straight as possible during use. See figures 1 & 2.

Never add / remove tension when the cable is extended from the reel. The cable must always be fully wound on the reel.

TENSION ADJUSTMENT

1. Hold shaft securely with wrench and remove 2 screws from hub.

2. Turn shaft clockwise / counter-clockwise to add / remove tension (one full turn at a time).

3. When desired tension is achieved, replace the 2 screws.

RATCHET LOCK USE

Engage ratchet lock by pulling cable out to desired position and letting it retract SLOWLY until lock engages. To release lock,

quickly pull cable out a short distance and allow it to begin to retract-it operates like a window shade. Locking feature may be

turned off by turning knob on side of reel.

DO NOT allow cable to retract in an uncontrolled manner. Always guide cable back to reel. Failure to do so can result in

damage to reel or personal injury.

DANGER

Grounding Reels

Page 2 www.reelcraft.com

REGULAR MAINTENANCE

1. Reel is factory lubricated for life. No additional lubrication required.

2. Periodically check cable for wear. If wear is detected, cable should be replaced immediately. If cable replacement is

required, order cable assembly kit no. 5 which contains cable and related parts, hardware and instructions. See parts list

for details.

SPRING REPLACEMENT

DO NOT attempt to remove spring motor from its canister. Doing so can result in damage to reel or personal

injury.

DANGER

Spring motors are self-contained for safe and easy handling. If spring motor replacement is required, it should be replaced as

a unit by ordering spring motor kit no. 1 which contains the spring motor, spool, shaft and bushings in a sealed canister. See

parts list for details.

RATCHET LOCK REPLACEMENT

For your convenience, the ratchet lock assembly has been included in two separate replacement kits. Order either the hard-

ware assembly kit no. 6, or the RH housing assembly kit no. 2. See parts list for details.

Item

Number

G 3050

G 3050 Y

G 3050 N

GS3050 Description

1 G 3050-K01 GS3050-K01 Spring motor assembly: spring motor, shaft and bushings in sealed container

2 G 3050-K02 GS3050-K02 RH housing assembly: RH housing half, ratchet lock assembly (attached to housing)

3 G 3050-K03 GS3050-K03 LH housing assembly: LH housing half, nameplate

4 G 3050-K04 Cable guide

5 G 3050-K05 GS3050-K05 Cable assembly: cable, grounding clamp(s), lockwasher-M4, hex nut-m4 (see notes below)

6 G 3050-K06 GS3050-K06

Hardware package: spacer, torsion spring, slotted machine screws M4 x 14mm (3), slotted

machine screws M4 x 8mm (6), lockwasher-M4 (10), hex nut-M4 (10), retaining ring (3),

extension spring, ratchet lock assembly

7 S602413 Cable stop

CABLE OPTIONS

(Number 5)

“Y” cable assembly (two clips),

add -Y to the part number.

EXAMPLE: G 3050-K05-Y

Nylon covered cable, add -N to

the part number.

EXAMPLE: G 3050-K05-N

NOTE:

RH housing assembly (no. 2)

includes ratchet lock assembly

and ground shoe attached

to housing.

*For G 3050 Y models with “Y” cable (two grounding clamps), order part number G 3050-K05Y.

For G 3050 N models with nylon covered cable, order part number G 3050-K05N.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ReelCraft Outils

ReelCraft

ReelCraft 81100 OHP Manuel utilisateur

ReelCraft

ReelCraft RS7000 Series Manuel utilisateur

ReelCraft

ReelCraft 5000 Series Manuel utilisateur

ReelCraft

ReelCraft D9000 Series Manuel utilisateur

ReelCraft

ReelCraft 7000 Series Manuel utilisateur

ReelCraft

ReelCraft SW7000 Series Manuel utilisateur

ReelCraft

ReelCraft RT402-OLP Manuel utilisateur

ReelCraft

ReelCraft UR82000 OLB Manuel utilisateur

ReelCraft

ReelCraft 4000 Series Manuel utilisateur

ReelCraft

ReelCraft G3050 Manuel utilisateur

ReelCraft

ReelCraft 5000 Series Manuel utilisateur

ReelCraft

ReelCraft 7000 Series Manuel utilisateur

ReelCraft

ReelCraft 7800 OLS Manuel utilisateur

ReelCraft

ReelCraft 4000 Series Manuel utilisateur

ReelCraft

ReelCraft 7000 Series Manuel utilisateur

ReelCraft

ReelCraft 5005 Series Manuel utilisateur

ReelCraft

ReelCraft 30000 Series Manuel utilisateur

ReelCraft

ReelCraft 7000 Series Manuel utilisateur

ReelCraft

ReelCraft 82000 OLP Manuel d'utilisation et d'entretien

ReelCraft

ReelCraft LD2030 163 9 Manuel utilisateur

ReelCraft

ReelCraft 7000 Series Manuel utilisateur

ReelCraft

ReelCraft E9000 Series Fiche technique

ReelCraft

ReelCraft D80000 Series Manuel utilisateur

ReelCraft

ReelCraft 7600 OLP Manuel utilisateur

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser