Redback A 4031B Manuel utilisateur

Operating Manual

A 4031B 30 Watt Public Address Amplifier

A 4033B 30 Watt Public Address Amplifier Rack Mount

Redback®Proudly Made In Australia

IMPORTANT NOTE:

Please read these instructions carefully from front to back prior to installation. They include important setup instructions.

Failure to follow these instructions may prevent the system from working as designed.

A 4031B

A 4033B

2Redback®Proudly Made In Australia

FEATURES

• 3 Inputs suitable for either microphone or line level, or for use as microphone and line level coupled together. disc, cassette, tuner, etc.

• Bass and treble controls (on both microphone and auxiliary inputs).

• Full 30W RMS output (100V and 4 -16Ωoutputs).

• Push to talk muting.

• Protection against over-voltage, over current, thermal run-away and short circuit load.

• Internationally accepted IEC mains socket (240V AC operation only).

• Stereo RCA sockets for all auxiliary inputs (configured to mono internally allowing standard stereo equipment to be directly connected).

• Fully balanced microphone inputs.

• Tape output, suitable for recording, or for connection to a second amplifier.

• Ten year warranty.

CONNECTIONS

Microphone 1

There are three types of sockets on the rear of the amplifier for microphone one. These are 6.35 mm (unbalanced) jack, 5 pin din, or 3 pin XLR

female. The 5 pin din has facility for PTT (push to talk) muting. The PTT contacts will mute input 2 (mic 2 and aux 2) and input 3 (mic 3 and

aux 3). The PTT contacts will not mute Aux 1 input. Wiring for 5 pin din socket is as per Fig 1. We recommend that you connect only one

microphone at a time to input 1.

For connection to the 3 pin XLR sockets refer to Fig 2.

Microphones 2 and 3

These are via 3 pin XLR sockets. Refer to Fig 2 for wiring these.

Speaker Outputs

Screw terminals are provided for both VC (voice coil) and 100V outputs. Minimum impedance for 100V loads is 333Ω(When only the 100V

output is used).Minimum impedance when only VC output is used is 8-16Ω@ 30W total load. A combination of 100V and VC is possible how-

ever we do not recommend this. If more than 30W is used then the unit may shut down due to overloading.

Tape Out

This is a mono output configured for a stereo lead for direct connection to a stereo source. This is suitable for connection to an auxiliary input

on external equipment. This is also suitable for driving 600Ωloads.

JP1 JP2

Configuration 1

When both jumpers are set to the outside the following logic applies...

•When paging through input 1, the VOX switch (where fitted) mutes

both inputs 2 and 3.

•When the PTT contacts on input 1 are closed, both inputs 2 and 3

are muted.

•Paging through input 2 or input 3 has no effect on any other input.

Note

1-There is no PTT facility on inputs 2 and 3.

2 - The PTT facility on microphone 1 will not mute Aux.1.

Configuration 2

When both jumpers are set to the inside the following logic applies...

• When paging through input 2, the VOX switch mutes input 3.

• When the PTT contacts on input 1 are closed, input 3 is muted.

• Paging through input 3 has no effect on any other input.

Note

1 - There is no PTT facility on inputs 2 and 3.

2 - There is no priority between input 1 and input 2 in this

configuration, i.e. paging on both inputs 1 and 2 simultaneously will

mean they mix together.

INTERNAL JUMPER SETTINGS

The amplifier has 3 sets of internally selectable jumpers, located as per figure 3.

VOX Muting Adjustments

VOX can be selected ON or OFF on the board via JP3.

1-VR1 adjusts the VOX sensitivity (i.e. input level that will activate switch). Turning the trimpot anticlockwise (as viewed from top) will make the

VOX switch less sensitive. This will prevent unwanted activation due to high ambient (background noise).

2 - VR2 adjusts the tail length (i.e. time before switching off) of the VOX switch. Turning VR2 anti-clockwise will increase the tail length.

Important Note: There are only two combinations of jumper settings for JP1 and JP2:

• Configuration 1: both jumpers set to the outside

• Configuration 2: both jumpers set to the inside

No other combinations can be used.

JP1 JP2

Redback®Proudly Made In Australia

Figure 1 - Inside top view of amplifier, showing the location VOX adjustments.

OPERATION

Once all inputs and outputs are connected:

1 - Turn bass and treble to midway point.

2 - Turn all volume controls to zero.

3 - Turn power switch on. Power indicator should illuminate.

4-Turn on microphone or auxiliary input source and adjust appropriate volume control to desired level.

The microphone and auxiliary for each input are mixed together, e.g. mic 1 and aux 1 are mixed. Both the mic and auxiliary inputs can be run

together but note there is only the one volume control for both of these.

TROUBLESHOOTING

No Power

(Power LED light does not illuminate)

Check mains fuse. Only replace with M205, 240V AC 0.5A rated fuse.

Distorted output

Check that the speaker type is correct for the output that you are using. Check for any short circuits on the speaker line.

Very low output

Make sure that the input is the correct level (check for shorted connectors). Check for any short circuits on the speaker line.

Continually blows fuses

Make sure that the speaker line is not shorted. Check also speaker types, ratings and if on correct output.

Amplifier keeps cutting in and out

Make sure that there is adequate ventilation around the amplifier. Check the vent slots on the case are not covered or blocked. Check also

speaker types, ratings and for any short circuits on the speaker line.

4Redback®Proudly Made In Australia

BALANCED

AUDIO

PTT

Figure 2 - 5 Pin din socket

wiring diagram. As viewed

from the rear of the amplifier.

From Microphone

Input

Unbalanced

Signal

Shield

XLR Mic

Input

From Microphone

Input

Balanced

Shield

XLR Mic

Input

Signal

Figure 3 - Microphone Connections

Connector Type:........................................................XLR 3Pin Female

Pin 1: .........................................................................................Earth

Pin 2: ....................................................................Signal Inphase (hot)

Pin 3: ...........................................................Signal Out of Phase (cold)

FOR P.T.T. (Push To Talk) paging use the 5 pin din input on mic 1

SPECIFICATIONS

POWER OUTPUT: 30 Watts RMS

T.H.D.: typically < 0.5% @ 1kHz

FREQUENCY RESPONSE

Microphone: 52Hz - 10kHz, ±3dB

Auxiliary: 40Hz - 10kHz, ±3dB

SPEAKER OUTPUTS: 100V (330Ω) (floating)

or 8 - 16Ω(0V referenced)

NOISE LEVEL: All volume controls min:

typically 76dB below rated output

(All inputs display same signal to noise ratio)

OUTPUT CONNECTORS

Speakers: Screw Terminals

Tape Output: RCA Stereo Socket

INPUT SENSITIVITY

Mic 1: 2.6mV Balanced

or 3.2mV Unbalanced

Mic 2: 2.6mV Balanced

Mic 3: 2.6mV Balanced

Aux 1: 150mV

Aux 2: 150mV

Aux 3: 150mV

MUTING: PTT Via Microphone

Switch Contacts

or Optional VOX Muting

-79dB below rated output

INPUT CONNECTORS

Mic 1: 5 pin DIN balanced

or 3 pin XLR balanced

or 6.35mm jack unbalanced

Mic 2: 3 pin XLR balanced

Mic 3: 3 pin XLR balanced

Aux 1: RCA Stereo Socket

Aux 2: RCA Stereo Socket

Aux 3: RCA Stereo Socket

240V AC Power: IEC Type Chassis Socket

CONTROLS

Input 1 (Mic 1 / Aux 1): Volume

Input 2 (Mic 2 / Aux 2): Volume

Input 3 (Mic 3 / Aux 3): Volume

Bass: ±10dB @ 100Hz

Treble: ±13dB @ 10kHz

Power: On/Off Switch

POWER SUPPLY 240V AC

INDICATORS: Power on LED

PROTECTION: AC Fuse 0.5A

DC Fuse 2 x 3A

DIMENSIONS

A 4031B: ≈300W x 220D x 80H mm

A 4033B: ≈483W x 220D x 88H mm

WEIGHT:

A 4031B: ≈4.1kg

A 4033B: ≈5.1kg

ACCESSORIES IEC Mains Lead

* Specifications Subject to Change Without Notice

Ce manuel convient aux modèles suivants

Autres manuels Redback Amplificateur

Redback

Redback A 4387A Manuel utilisateur

Redback

Redback PHASE 5 A 4390 Manuel utilisateur

Redback

Redback Phase 4 Guide d'installation

Redback

Redback A 4210 Manuel utilisateur

Redback

Redback A4260 Manuel utilisateur

Redback

Redback A 4270 Manuel utilisateur

Redback

Redback A 4230A Manuel utilisateur

Redback

Redback A 4370A Manuel utilisateur

Redback

Redback A 4372 Manuel utilisateur

Redback

Redback A 1922A Manuel utilisateur

Redback

Redback A 4931 Manuel utilisateur

Redback

Redback PHASE 5 A 4264 Manuel utilisateur

Redback

Redback A 4314 Manuel utilisateur

Redback

Redback A 1937 Manuel utilisateur

Redback

Redback A 4205 Manuel utilisateur

Redback

Redback A 4937 Manuel utilisateur

Redback

Redback A 4037 Manuel utilisateur

Redback

Redback A4260B Manuel utilisateur

Redback

Redback A 4230 Manuel utilisateur

Redback

Redback A 4377A Manuel utilisateur

Redback

Redback A 4116 Manuel utilisateur

Redback

Redback A 4017 Manuel utilisateur

Redback

Redback A 4235 Manuel utilisateur

Redback

Redback A 4860 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur