RCA RTU6549-B Manuel utilisateur
RTU6549-B
65” LED TV
USER’S MANUAL
Contents
Introduction
Warning
Caution
Important Information
Attaching or Removing the Stand
Installing Batteries to the Remote Control
Identifying Front and Rear Panel
Connection Suggestion
Main Unit Description
Remote Control
OSD Basic Adjustment
How Do I Clean The TV
Troubleshooting
Specifications
FCC Compliance Statement
2
Introduction
Thank you very much for purchasing your LED TV. It serves as a normal colour TV.
To enjoy your set fully from the very beginning, read this manual
it handy for future reference.
INSTALLATION
ķLocate the receiver in the room where direct light does not strike the screen. Total
darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect
lighting is recommended for comfortable viewing.
ĸAllow enough space between the receiver and the wall to permit ventilation.
ĹAvoid excessively warm locations to prevent possible damage to the cabinet or
premature component failure.
ĺThis TV can be connected to AC 100-240V~ 50/60HZ.
ĻDo not install the TV in a location near heat sources such as radiators, air ducts,
direct sunlight, or in closed compartments and closed areas. Do not cover the
ventilation openings when using the TV.
The indicator light will last for about 30 seconds after the power has been turned
off.
Wait until the indicator light goes out before repowering the TV.
6
User manual x1
Warranty card x1
Remote control x1
Battery (pair, AAA) x1
Accessories list for this TV set:
x
x
x
x
carefully and keep
3
Warning
This symbol is intended to alert the user to avoid the risk
of electric shock. This equipment may only be disassembled
by qualified service personnel.
This symbol is intended to alert the user to the presence
of important operation and maintenance instructions in
the literature accompanying the equipment.
CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER- SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Class I structures of equipment should be connected to the grid
power output with a protective earth connection on the socket.
Power plug as a broken applianceˈbroken installations should
be easy to operate.
4
Caution
Caution
High voltages are used in the operation of this product.
-Do not open the product's casing. Refer servicing
to qualified service personnel .
Caution
Toprevent fire or electrical shock hazard, do not expose
the main unit to rain or moistureˈdo not place objects
filled with liquids, such as vases, on the apparatus.
Caution
Do not drop or push objects into the television cabinet
slots or openings. Never spill any kind of liquid on the
television receiver.
Caution
Avoid exposing the main unit to direct sunlight and other
sources of heat. Do not stand the television receiver
directly on other products which give off heat: e. g. video
cassette players and audio amplifiers. Do not block the
ventilation holes in the back cover. Ventilation is essential
to prevent failure of electrical components. Do not squash
the power supply cord under the main unit or other heavy
objects.
5
Caution
Caution
Never stand on, lean on or suddenly push the product
or its stand. You should pay special attention to
children.
Caution
Do not place the main unit on an unstable cart stand,
shelf or table. Serious injury to an individual and
damage to the television may result if it should fall.
Caution
When the product is not used for an extended period
of time, it is advisable to disconnect the AC power
from the AC outlet.
Caution
The LED panel used in this product is made of glass and
is therefore breakable. This product must not be dropped
or banged. If the LED Panel breaks be careful of being
injuredbybrokenglass.
6
Television Antenna Connection Protection
Important Information
External Television Antenna Grounding
If an outside antenna or cable system is to be connected to the TV, make sure that the antenna or
cable system is electrically grounded to provide some protection against voltage surges and
static charges. Article 810 of the National Electrical Code, ANSI/NFPSA 70, provides
information with regard to proper grounding of the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit, size of the grounding conductors, location of
antenna discharge unit, connection to grounding electrodes, and requirements of the grounding
electrode.
Lightning Protection
For added protection of the TV during a lightning storm or when it is left unattended or unused
for long periods of time, unplug the TV from the wall outlet and disconnect the antenna or cable
system.
Power Lines
Do not locate the antenna near overhead light or power circuits, or where it could fall into such
power lines or circuits.
7
Attacthing or Removing the Stand
Lay the TV face-down on a flat, cushioned
surface to avoiddamaging or scratching.
1. Lay the TV face-down on a flat,
cushioned surface to avoid
damaging or scratching.
2. Untighten the 4 pcs screws holding
the stand assembly and remove them.
3. Attach the wall-mount bracket to
the TV using the mounting holes
on the back of the TV. Mount this
TV according tothe instructions
included in the wall-mount bracket.
This apparatus is intended to be supported by UL Listed wall mount bracket.
First Step: Assembling stand and stand
column by using M4x10mm x 4 pcs
screws.
Second Step: Lock the stand and stand
column to TV set by M4x14mm X4 pcs
screws.
First Step
Second Step
Attacthing or Removing the Stand
Lay the TV face-down on a flat, cushioned
surface to avoiddamaging or scratching.
1. Lay the TV face-down on a flat,
cushioned surface to avoid
damaging or scratching.
2. Untighten the 4 pcs screws holding
the stand assembly and remove them.
3. Attach the wall-mount bracket to
the TV using the mounting holes
on the back of the TV. Mount this
TV according tothe instructions
included in the wall-mount bracket.
This apparatus is intended to be supported by UL Listed wall mount bracket.
First Step: Assembling stand and stand
column by using M4x10mm x 4 pcs
screws.
Second Step: Lock the stand and stand
column to TV set by M4x14mm X4 pcs
screws.
First Step
Second Step
8
9
Installing Batteries to the Remote Control
Please insert two AAA batteries into the remote control. Make sure that you match the (+)
and (-) symbols on the batteries with the (+) and (-) symbols inside the battery compartment.
Afterwards, re-attach the battery cover.
Please note:
Only use AAA batteries.
Do not mix new and old batteries. This may result in cracking or leakage that may pose a
fire risk or lead to personal injury.
Inserting the batteries incorrectly may also result in cracking or leakage that may pose a
fire risk or lead to personal injury.
Dispose the batteries in accordance with local laws and regulations.
Keep the batteries away from children and pets.
If the remote control is not used for a long time, remove the batteries.
Keep the remote control away from moisture, sunlight, and high temperatures.
10
Table des matières
Langues :
Autres manuels RCA Téléviseur LED
RCA
RCA LED24G45RQ Manuel utilisateur
RCA
RCA RNSMU5836 Manuel utilisateur
RCA
RCA RLEDV2488A-C Manuel utilisateur
RCA
RCA RLDED5099-UHD Manuel utilisateur
RCA
RCA DECG13DR Manuel utilisateur
RCA
RCA RLEDV2238A Manuel utilisateur
RCA
RCA RNSM4003-B Manuel utilisateur
RCA
RCA RTU5540 Manuel utilisateur
RCA
RCA SLD40HG45RQ Manuel utilisateur
RCA
RCA PROSCAN PLED6515-C-UHD Manuel utilisateur
RCA
RCA LED46A55R120Q Manuel utilisateur
RCA
RCA RLED6515-UHD Manuel utilisateur
RCA
RCA RTDVD1900-C Manuel utilisateur
RCA
RCA RLDED4016A-D Manuel utilisateur
RCA
RCA RS65U2-EU Manuel utilisateur
RCA
RCA J32LED750 Manuel utilisateur
RCA
RCA RS22H2C Manuel utilisateur
RCA
RCA TR3201A Manuel utilisateur
RCA
RCA RCA RS43F1-EU Manuel utilisateur
RCA
RCA RLEDV1920A Manuel utilisateur
