Raven Hawkeye Mode d’emploi

016-0171-598 Rev. B 05/17 E29361

Hawkeye® Quick

Start Guide

While every effort has been made to ensure the accuracy of

this document, Raven Industries assumes no responsibility

for omissions and errors. Nor is any liability assumed for

damages resulting from the use of information contained

herein.

Raven Industries shall not be responsible or liable for

incidental or consequential damages or a loss of anticipated

benefits or profits, work stoppage or loss, or impairment of

data arising out of the use, or inability to use, this system or

any of its components. Raven Industries shall not be held

responsible for any modifications or repairs made outside our

facilities, nor damages resulting from inadequate

maintenance of this system.

As with all wireless and satellite signals, several factors may

affect the availability and accuracy of wireless and satellite

navigation and correction services (e.g. GPS, GNSS, SBAS,

etc.). Therefore, Raven Industries cannot guarantee the

accuracy, integrity, continuity, or availability of these services

and cannot guarantee the ability to use Raven systems, or

products used as components of systems, which rely upon

the reception of these signals or availability of these services.

Raven Industries accepts no responsibility for the use of any

of these signals or services for other than the stated purpose.

Disclaimer

©Raven Industries, Inc. 2015

Manual No. 016-0171-598 Rev. B 1

Contents

Overview 2

Requirements 2

Machine Configuration 2

Initial Hawkeye Configuration 5

Finalizing Machine Configuration 6

Additional Information 7

2 Hawkeye Start-Up Guide

Overview

This quick guide provides directions for machine configuration and the first-

time setup of a HawkeyeTM system on a Viper®4. If installing a Hawkeye

system on an machine with an existing Viper 4, only perform the steps in the

Initial Hawkeye Configuration section.

Note: Since Hawkeye utilizes an ISO control platform, the directions in the

Initial Hawkeye Configuration should be similar on other computers

than Viper 4.

The steps in this document should only be performed after the Hawkeye

system has been installed in accordance with the machine specific Hawkeye

installation manual.

Requirements

• Hawkeye Hardware Installed on the Machine

• Viper 4 with ROS 2.1.0 or Newer

• Virtual Terminal and Task Controller Unlocks Installed.

Machine Configuration

If this is the first time using a Viper 4 on this machine:

1. Power on the Viper 4.

At Raven Industries, we strive to make your experience with our

products as rewarding as possible. One way to improve this experience

is to provide us with feedback on this manual. Your feedback will help

shape the future of our product documentation and the overall service

we provide. We appreciate the opportunity to see ourselves as our

customers see us and are eager to gather ideas on how we have been

helping or how we can do better. To serve you best, please send an

email with the following information to:

[email protected]

-Hawkeye Start-Up Guide

-Manual No. 016-0171-598 Rev. B

-Any comments or feedback (include chapter or page numbers if

applicable).

-Let us know how long have you been using this or other Raven

products.

We will not share your email or any information you provide with anyone

else. Your feedback is valued and extremely important to us.

Thank you for your time.

Manual No. 016-0171-598 Rev. B 3

2. Select the desired language from the drop-down menu.

3. Read the end user License Agreement.

4. Press OK to accept. A New Machine Configuration Detected Window will

open.

5. Press OK. The Please Select a Machine Type window will open.

4 Hawkeye Start-Up Guide

6. Select the appropriate machine type from the machine icons.

7. Press OK. The Machine Configuration Name window will open. Enter the

desired name and press the check mark to accept. The Machine Profile

window will open.

Note: If you pick a machine from the machine database, do not select one of

the standard boom configurations. The boom setup will be setup during

the Initial Hawkeye Configuration process.

8. Select the machine Type, Sub-Type, Manufacturer, and Model.

9. Press OK. The Self-Propelled-General Information tab will open.

10.Select the Self-Propelled - Measurements (second) tab.

11.Enter the location in relation to the machine in addition to the GPS unit

height.

12.Enter the machine Wheel Base information.

Manual No. 016-0171-598 Rev. B 5

Initial Hawkeye Configuration

1. Press the VT Menu button.

2. Walk through all of the steps in the setup wizard. For this you will need the

following information:

Note: If, at any point during the setup wizard you have a question, press the

??? button by the item for more information.

3. Press the tools button.

Number of Nozzle Control Valves

Applicator Type

Nozzle Spacing

Tip Size

Fence Rows (if needed)

Number of Sections

Section Widths

Boom Offset

Switch Mapping (if needed)

Boom Pressure Calibration

Valve Calibration

Flow Meter Calibration

Target Rate

Target Pressure

6 Hawkeye Start-Up Guide

4. Review and adjust the settings on the Calibration Summary page.

5. Press Next Page.

6. Review and information on the second Calibration Summary page. Any

adjustments to these settings must be done through the machine settings.

7. Press Previous Page.

8. Press Calibrate NCVs. The NCV calibration process will begin.

Finalizing Machine

Configuration

1. Press the Machine icon. The machine Setup window will open.

Manual No. 016-0171-598 Rev. B 7

2. Select the Self-Propelled - Equipment (third) tab.

3. Press the plus (+) sign. The boom configuration will generate.

Note: If a boom configuration already exists, delete it before importing a new

boom configuration, To do so, press the trash can by the profile.

The boom configuration should automatically populate the boom group

without any additional information from the user. If asked to name the

boom group and enter the number of sections, stop the configuration

process. Exit out of the boom group configuration, cycle power on the

machine, and restart the machine.

4. Press the modify button.

5. Verify the boom offset.

6. Verify red boom is no longer visible on the machine icon.

7. Initial set-up and calibration is complete.

Additional Information

For additional information on advanced Hawkeye settings, refer to the

Hawkeye Calibration and Operation manual included with the kit.

8 Hawkeye Start-Up Guide

Autres manuels pour Hawkeye

Table des matières

Autres manuels Raven Matériel agricole

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven RS1 Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven SC1 Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven FLOWMAX 220 Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven AutoBoom Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven AccuBoom Manuel utilisateur

Raven

Raven Hagie Hawkeye STS Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven SC1 HDU Manuel utilisateur

Raven

Raven Case IH AutoBoom XRT Manuel d'utilisation et d'entretien

Raven

Raven TC1 Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven AutoBoom Manuel d'utilisation et d'entretien

Raven

Raven Unverferth NutriMax Series Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven SC1 Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Raven

Raven SmarTrax Manuel utilisateur

Manuels Matériel agricole populaires d'autres marques

GSi

GSi PNEG-2314 Manuel utilisateur

Checchi & Magli

Checchi & Magli TEXDRIVE Manuel utilisateur

Amazone

Amazone Cenius 4003-2TX Manuel utilisateur

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manuel utilisateur

Cima

Cima BLITZ Instructions d'utilisation et d'entretien

Amazone

Amazone CombiDisc 3000 Instructions d'installation

HE-VA

HE-VA Disc-Roller XL Contour Manuel utilisateur

AGT

AGT AGT-SSFM Manuel utilisateur

Milestone

Milestone 72-84 Manuel utilisateur

KUHN

KUHN Hector 3000 Manuel utilisateur

Krone

Krone X-Disc 6200 Manuel utilisateur

Eliet

Eliet DZC450 Manuel utilisateur

Taarup

Taarup BIO+ B4000 Manuel utilisateur

Garland

Garland SHAKER 310 DPG Manuel utilisateur

stable comfort

stable comfort StableWall System Manuel utilisateur

International

International 710 Manuel utilisateur

Ashland

Ashland HDW-3217-14 Manuel utilisateur

TURF TANK

TURF TANK One+ Manuel utilisateur