Radionics D8024 Manuel utilisateur

D8024 Analog Fire Alarm Control Panel

Operator’s Guide

Radionics

POWER

SYSTEMTROUBLE

TROUBLESILENCED

ALARMSILENCED

POINTBYPASSED

ALARM

System

ResetTrouble

Silenced Silence

AlarmAlarm

ManualKeypad

Enable

Disable

Keypad

Radionics

D8024

Table of Contents

D8024 Operator’s Guide

1.0 Notice.............................................................................................................................................................................3

2.0 Warnings and Cautions................................................................................................................................................3

3.0 FCC Notices...................................................................................................................................................................3

Part 15...............................................................................................................................................................................3

4.0 UL/NFPA Notices...........................................................................................................................................................3

5.0 Control Levels ...............................................................................................................................................................4

5.1 Level Distinction ..........................................................................................................................................................4

5.2 Passcodes...................................................................................................................................................................4

6.0 Controls and Displays ..................................................................................................................................................4

7.0 Level One (Display) Functions.....................................................................................................................................5

7.1 Power Conditions ........................................................................................................................................................5

7.2 Trouble Conditions ......................................................................................................................................................6

7.3 Alarm Conditions.........................................................................................................................................................6

8.0 Level Two (Controller) Functions................................................................................................................................6

8.1 Power Conditions ........................................................................................................................................................7

Power Failure Signal......................................................................................................................................................7

Power Failure Signal Response.....................................................................................................................................7

8.2 Trouble Conditions ......................................................................................................................................................7

Trouble Signals..............................................................................................................................................................7

Trouble Signal Response...............................................................................................................................................7

8.3 Alarm Conditions.........................................................................................................................................................7

Alarm Signals.................................................................................................................................................................7

Alarm Signal Response .................................................................................................................................................8

8.4 System Operation........................................................................................................................................................8

System Tests.................................................................................................................................................................8

LEDs Test...................................................................................................................................................................9

LCD Test....................................................................................................................................................................9

Zones Test .................................................................................................................................................................9

Time Setting.................................................................................................................................................................10

Enable/Disable Functions............................................................................................................................................10

Enable/Disable by Zone...........................................................................................................................................10

Enable/Disable Individual Detection Devices (Inputs)..............................................................................................11

Enable/Disable Panel Keys......................................................................................................................................11

Enable/Disable Delayed Day Mode..........................................................................................................................11

Enable/Disable Relays.............................................................................................................................................11

Print Functions.............................................................................................................................................................12

Print Devices............................................................................................................................................................12

Print Events (Event Log) ..........................................................................................................................................12

Print Mode................................................................................................................................................................12

Print Direction...........................................................................................................................................................12

Print Disabled...........................................................................................................................................................12

View Functions.............................................................................................................................................................12

View Devices............................................................................................................................................................13

View Event Log ........................................................................................................................................................13

View Faults...............................................................................................................................................................13

View Outputs............................................................................................................................................................13

View Disablements...................................................................................................................................................13

9.0 Level Three (Programmer) Functions .......................................................................................................................13

Table of Figures

D8024 Operator’s Guide

Figure 1: D8024 Fire Alarm Control Panel............................................................................................................................4

Figure 2: D8024 Front Panel Display, Hinged Panel Open...................................................................................................5

Figure 3: LED Display...........................................................................................................................................................6

Figure 4: Level Two Entry Menu One....................................................................................................................................6

Figure 5: Level Two Entry Menu Two....................................................................................................................................6

Figure 6: Main Menu .............................................................................................................................................................6

Figure 7: Enable Menu..........................................................................................................................................................6

Figure 8: Level Two Controls ................................................................................................................................................8

Figure 9: Main Menu .............................................................................................................................................................8

Figure 10: Test Menu............................................................................................................................................................8

Figure 11: Zone Test Menu One...........................................................................................................................................9

Figure 12: Zone Test Menu Two...........................................................................................................................................9

Figure 13: Zone Test Menu Three.........................................................................................................................................9

Figure 14: Zone Test Menu Four ..........................................................................................................................................9

Figure 15: Main Menu .........................................................................................................................................................10

Figure 16: Enable/Disable Menus.......................................................................................................................................10

Figure 17: Print Menu..........................................................................................................................................................12

Figure 18: View Menu .........................................................................................................................................................13

Table of Tables

Table 1: Control Key Functions.............................................................................................................................................4

Table 2: Alphanumeric and Program/Interactive Key Functions...........................................................................................4

D8024 Analog Fire Alarm Control Panel

D8024 Operator’s Guide

Operator’s Manual

1.0 Notice

• The material and instructions covered in this manual have been carefully checked for accuracy and are presumed to

be reliable. However, the manufacturer assumes no responsibility for inaccuracies and reserves the right to modify

and revise this document without notice.

• These instructions are the Operator’s Manual at the Display, Control, and Limited Programming Levels of operation.

See the Installation Manual for information on installation and powering the D8024 Fire Alarm Control Panel (FACP).

See the Programmer’s Guide for information on programming and Level Three operation of the system

2.0 Warnings and Cautions

These instructions contain procedures to follow in order to avoid injury and damage to equipment.

3.0 FCC Notices

Part 15

• This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

commercial installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed

in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment on and off, the user

is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and the receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

4.0 UL/NFPA Notices

• UL listed for NFPA 72, Local.

• All references to NFPA and related requirements are based upon compliance with the 1993 edition of NFPA 72,

National Fire Alarm Code. Since installation specifications are nearly always based upon a specific edition of a

standard that has been legally adopted by the Authority Having Jurisdiction (AHJ), earlier editions of NFPA

standards will generally apply. Consult with the appropriate AHJ for confirmation.

D8024 Operator’s Guide

5.0 Control Levels

5.1 Level Distinction

• The D8024 has three available control levels. At all three levels the LED Display indicates condition, the

ZONE/AREA LEDs indicate location, and detailed alarm/trouble information is displayed alphanumerically.

•• Control Level One, the Display Level, inhibits the system control keys, limiting the front panel function to

annunciation.

•• Control Level Two, the Controller Level, allows system control for Fire Drill, Alarm Silence, Trouble Silence, and

System Reset; and allows Test and Enable/Disable operations, but does not allow access to configuration or

programming functions. At Level Two, the Alphanumeric Display becomes interactive and prompts for system

checks, log functions, and key status. Level Two is reached by entering a pass code from Level One.

•• Control Level Three, the Programmer’s Level, allows full system configuration information and is used to program

the system or modify the program. Level Three is reached by passcode from Levels One or Two. See the Analog

Fire Alarm Control Panels Programming Guide (P/N: 38789B) for more information on Control Level Three.

Figure 1: D8024 Fire Alarm Control Panel

5.2 Passcodes

• Ten passcodes are available for D8024 Controllers. Passcodes are programmable. The Level Two passcode is

assigned or changed from Level Three and will not allow access to Level Three. See the Analog Fire Alarm Control

Panels Programming Guide (P/N: 38789B) for details.

6.0 Controls and Displays

• The D8024 control panel has two rows of control keys. The vertical row of Control Keys contains the four System

Control Keys for Fire Drill, Alarm Silence, Trouble Silence, and System Reset. Opening the hinged panel below the

Zone/Area Display provides access to the Alphanumeric Keys and the three Program/Interactive Keys.

Table 1: Control Key Functions

Key Label Function

Fire Drill Turns on ALL Notification Appliances.

Alarm Silence Press to Silence all Notification Appliances.

Press again to activate all Notification Appliances.

Trouble Silence Acknowledges events and silences the internal buzzer.

System Reset Cancels all alarm conditions and resets the panel.

• The Alphanumeric Keys normally function as number keys. They can be toggled to Letter Keys by pressing the

Change Key at the right end of the alphanumeric key row. The Shift Key at the left end of the Alphanumeric Keys

toggles between upper and lower row of letters. Hold the Shift Key while entering another key to enter the bottom

letter.

Table 2: Alphanumeric and Program/Interactive Key Functions

D8024 Operator’s Guide

Key Label Function

Shift Shows user options on Alphanumeric Display.

Used in programming to allow letters N to Z.

0,1,2,3,4,5,6,7,8 9 Press to Silence all Notification Appliances.

Press again to activate all Notification Appliances.

>,< Scrolls through fires/faults on the Alphanumeric Display.

Change Changes a display option.

Enter Enters the selection.

No To answer No or terminate an option.

Yes To answer Yes or step through an option.

• The upper display, the Alphanumeric Display, is an illuminated two-line, 80-character, LCD display that gives

detailed information on system events and status, and displays interactive prompts.

• The middle display, the LED Display, indicates the type of system event and status.

Figure 2: D8024 Front Panel Display, Hinged Panel Open

• The lower display, the ZONE/AREA LED Display, indicates the location and type (alarm or trouble) of event. The

D8024 can have up to 20 zones.

7.0 Level One (Display) Functions

• At Level One, the Control Panel functions as an annunciator, and the Control Keys are disabled. Pressing any of the

Control Keys will result in a series of interactive messages on the Alphanumeric Display which end in a prompt for a

Level Two passcode.

7.1 Power Conditions

• When the system is being powered by 120V AC, the green AC Power LED at the lower right of the LED Display will

be lit. The normal Alphanumeric Display will alternate between a time and date message and a system status

message.

D8024 Operator’s Guide

Figure 3: LED Display

• If the 120V AC power source is interrupted, the AC Power LED will flash, the panel buzzer will sound, and the

System Trouble and the Earth Fault LEDs will light. The illumination will go out on the Alphanumeric Display, and

the Display will show an “AC Fail” message and provide information about the failure, the status of the standby

batteries, and will show the telephone number for service. Pressing the Trouble Silence Key will silence the panel

buzzer.

7.2 Trouble Conditions

• If a device fails to respond, is disabled, the response is not within normal parameters, or the system detects a fault,

the amber System Trouble or Fault LEDs will light. The amber Trouble LED in the ZONE/AREA section of the panel

will light to indicate the location, the panel’s internal buzzer will sound, and the Alphanumeric Display will provide

detailed information. If more than one fault is present, the display will automatically scroll through the first four.

7.3 Alarm Conditions

• The two red Alarm LED’s at the left of the LED Display flash to indicate the system has detected a fire condition.

The ZONE/AREA Alarm LED(s) lights, indicating the alarm location(s), and the Alphanumeric Display provides

detailed information. If more than one fire is present, the display will automatically scroll through the first four.

8.0 Level Two (Controller) Functions

• At Level Two, the Control Panel functions as a Controller (see 5.1 Level Distinction, page 4). To enable the

Control Keys (to enter Level Two), open the hinged panel and press the Shift Key. The alphanumeric display

prompts:

Figure 4: Level Two Entry Menu One

• Press the Yes Key. The display shows Level Two Entry Menu Two.

Figure 5: Level Two Entry Menu Two

• Enter the 4-digit level two passcode. The Display shows Main Menu.

Figure 6: Main Menu

• The D8024 has ten Level Two passcodes available. Level Two passcodes are assigned from Level Three, the

programmer’s level. Press Key 4 on the Alphanumeric Key row. The display shows the Enable Menu.

Figure 7: Enable Menu

D8024 Operator’s Guide

• Press Key 3 on the Alphanumeric Key row. The display returns to Main Menu. The Control Keys are now enabled

for the amount of time programmed into the panel. At the end of the programmed time period the panel will

automatically inhibit the Control Keys.

8.1 Power Conditions

• The D8024 supervises its AC power supply and the standby batteries

Power Failure Signal

• If the 120V AC power source is interrupted, the AC Power LED will flash, the panel buzzer will sound, and the amber

System Trouble and Earth Fault LEDs will light. The illumination will go out on the Alphanumeric Display, and the

Display will show an “AC Fail” message and provide information about the failure and the status of the standby

batteries. If the standby batteries fail, the AC Power LED will go out.

Power Failure Signal Response

• To silence the panel buzzer, enter Level Two, enable the Control Keys and press the Trouble Silence Key. The

amber Trouble Silenced LED will light.

• When the 120V AC power is restored, the green AC Power LED stops flashing and remains on, and the System

Trouble and Earth Fault LEDs go out. The amber CPU Reset LED lights while the system resets itself and goes out

when the reset is complete. The Alphanumeric Display returns to normal.

8.2 Trouble Conditions

• The system responds to other-than-normal conditions, which are not alarm conditions, by sounding the internal

buzzer and initiating a Trouble Condition.

Trouble Signals

• If a device fails to respond, is disabled, the response is not within normal parameters, or the system detects a fault,

the amber System Trouble or Fault LED will light. In addition, the amber Trouble LED in the ZONE/AREA section of

the panel will light to indicate the location, the panel’s internal buzzer will sound, and the Alphanumeric Display will

provide detailed information.

Trouble Signal Response

• To acknowledge the event, enter Level Two, enable the Control Keys, and press the Trouble Silence Key to mute

the internal buzzer (under certain circumstances, the system may override the mute). The amber Trouble Silenced

LED lights to indicate that condition. The system will not allow a reset until the problem is corrected. If necessary,

the system allows disabling of individual devices and zones. See page 10, “Enable/Disable Functions”, of this guide.

After correcting the problem, press the System Reset Key. The amber Trouble Silenced LED goes out and the

Alphanumeric Display returns to normal.

8.3 Alarm Conditions

• The panel will signal an alarm if it detects an Alarm condition or a Fire Drill test.

Alarm Signals

• If the control panel initiates an alarm condition, the red Alarm LEDs at the left of the LED Display flash to indicate the

system has detected a fire condition and has activated the system notification appliances, the internal buzzer

sounds, ZONE/AREA Alarm LED(s) light indicating the event location, and the Alphanumeric Display provides

detailed information.

• To test the alarm system, enter Level Two, enable the Control Keys, and press the Fire Drill Key. The panel will

activate system notification appliances. The red Alarm LEDs at the left of the LED Display flash and the internal

buzzer sounds. The Alphanumeric Display indicates a “Fire Test.”

D8024 Operator’s Guide

Figure 8: Level Two Controls

Alarm Signal Response

• Press the Alarm Silence Key to turn off notification appliances external to the panel. The Alarm Silenced LED will

light. Pressing the Alarm Silence Key again turns on the external notification appliances.

• Press the Trouble Silence Key to turn off the panel buzzer. The amber Trouble Silenced LED will light.

• Press the System Reset Key to reset the system. The Alarm and Trouble Silenced LEDs will go out and the

Alphanumeric Display will return to normal.

The panel will not accept a reset from an Alarm condition until the notification appliances have

been silenced.

• To return the system to Level One, press the Shift Key, and select 5) Disable from the Alphanumeric Display. Select

3) Keys from the display. The panel will briefly display the Level Two Entry Menu Two and then revert to the normal

display (alternating between a time and date display and a system status message). Press the Fire Drill Key to

verify that the keys are disabled.

8.4 System Operation

• Pressing the Shift Key from the normal display will open Main Menu on the Alphanumeric Display. The first option, 1

Commission, is not available to Level Two Operators. See the Programmer’s Guide for commissioning and

programming information. The other options on the Main Level permit tests and the setting, enabling, and disabling

of various system functions.

Figure 9: Main Menu

System Tests

• Select the second option, 2) Test, from the Main Menu to open the Test Menu. This allows the operator to test:

• The LEDs on the Front Panel Display

• The alphanumeric (Liquid Crystal) display

• Detection and alarm initiating devices connected to the polling circuit

• Notification Appliance and other alarm condition devices connected to the system.

Figure 10: Test Menu

• If no action is taken, the display reverts to the normal display after one minute.

D8024 Operator’s Guide

LEDs Test

• Select the first option, 1) LEDs, by pressing the 1 Key. The panel will flash all LEDs on the LED Display and step

through all the Alarm and Trouble LEDs in the ZONE/AREA Display. On completion of the test, press No to return

the display to Main Menu.

LCD Test

• Select the second option, 2) LCD, from the Test Menu by pressing the 2 Key. The Alphanumeric Display will flash all

characters in all spaces on the alphanumeric display and return to Main Menu.

Zones Test

• Select the third option, 3) Zones, from the Test Menu by pressing the 3 Key. The Zones Test allows the operator to

test devices on the polling circuit(s) and peripheral device circuit(s) without having to reset the panel after each

device is tested.

If no action is taken within one minute, the display reverts to the normal display. Press the > Key

to restore the test display.

• The panel displays Zone Test Menu One.

Figure 11: Zone Test Menu One

• Press the Yes Key to activate notification appliances briefly as each device is tested, or press the No Key to bypass

the indicator test. The panel displays Zone Test Menu Two.

Figure 12: Zone Test Menu Two

• Enter the number of the first zone to be tested. The panel displays Zone Test Menu Three. If, for example, “12”

were keyed in, the display would show:

Figure 13: Zone Test Menu Three

• If “15” were keyed in, the panel would display the Walk Test Mode as follows:

Figure 14: Zone Test Menu Four

• The “w” moving across the lower line alternates with a “Press NO to EXIT” message.

Once the display indicates the panel is in the Walk Test Mode, the display will not revert to normal.

The panel will terminate the test and sound the panel buzzer if there is no activity for a 20-minute

period.

• The operator may test devices within the zone parameters shown on the display. The panel responds to each test

by:

• Displaying an activation message on the Alphanumeric Display

• Entering the activation in the Event Log

• Lighting the Alarm LED in the ZONE/AREA Display

Autres manuels pour D8024

Table des matières

Autres manuels Radionics Détecteur de fumée

Radionics

Radionics D285 Manuel utilisateur

Manuels Détecteur de fumée populaires d'autres marques

x-sense

x-sense SD19-W Manuel utilisateur

BRK electronic

BRK electronic First Alert P1010 Manuel utilisateur

FireAngel

FireAngel Thermoptek ST-622 Manuel utilisateur

teko

teko Astra-42A Manuel utilisateur

Safetec

Safetec SDS-2/6 Manuel du propriétaire

Siemens

Siemens PE-11C Manuel utilisateur

System Sensor

System Sensor DH500ACDC Manuel utilisateur

Resolution Products

Resolution Products RE612 CryptiX Manuel utilisateur

First Alert

First Alert PC900V Manuel utilisateur

Eminent

Eminent EM6590 E-Domotica Manuel utilisateur

Ei Electronics

Ei Electronics Ei Ei168RC Manuel utilisateur

Carrier

Carrier Kidde Quell Q301 Manuel utilisateur

VESDA

VESDA VLF-500 Manuel utilisateur

ELRO

ELRO FS8110 Manuel utilisateur

Heiman

Heiman SMOKI NS-626PHS Manuel utilisateur

Regin

Regin SDD-S65 Manuel utilisateur

Family Gard

Family Gard FG225 Manuel utilisateur

Greystone

Greystone DSD120 Manuel utilisateur