Radionics D7024 Manuel utilisateur
© 1997 Radionics, Inc., Salinas, CA, U.S.A.All rights reserved.
™ The Radionics logo is a registered trademark of Radionics, Inc., Salinas CA, U.S.A. D7024 Reference Guide P/N 31499B
Reference Guide
for the
D7024 Control/Communicator
Radionics, Inc., 1800 Abbott Street
Salinas, CA 93901, U.S.A.
Customer Service: (800) 538-5807
6/20/97
Page2 Copyright© 1997Radionics, Inc. D7024Reference Guide
Table of Contents
Notices 3
FCC Compliance Notice 3
FCC Phone Connection to Users 3
Notice 3
1.0 Overview 4
1.1 System Overview 4
1.2 Specifications 4
1.2.1 Enclosure Housing 4
1.2.2 Temperature 4
1.2.3 Power 4
1.2.4 Outputs 4
1.2.5 Zones (Initiating Circuits) 4
1.2.6 Keypads 5
1.2.7 Communicator 5
1.2.8 Users 5
1.2.9 Lightning Protection 5
1.2.10 Backup Battery Calculation 5
1.2.11 Standby Current Load 5
2.0 Enclosure Installation 6
2.1 Install the Enclosure 6
2.2 Install the Control/Communicator 6
3.0 Control Terminal Wiring 7
4.0 System Worksheet 8
5.0 Operating Guide 11
5.1 Understanding the Built-in Keypad 11
5.2 Understanding the D7033 Keypad 11
5.3 System Operation 12
5.3.1 Modesof SystemOperation 12
5.3.2 Point/ZoneMapping 12
5.4 Fire Silence/Reset 13
5.5 SystemTrouble 13
5.6 Fire Safety 13
5.6.1 IfInstalled in Family Residences14
5.6.2 Having and Practicing an Escape
Plan 14
5.6.3 Installation Considerations 14
5.7 Personal Identification Numbers 15
5.8 Error Displays 15
5.9 Testing 15
5.10 Remote Program Dial-out and Answer16
6.0 How to Program 17
6.1 ALPHA Programming 18
6.2 Format Programming 18
6.2.1 4/2 18
6.2.2 BFSK 18
6.2.3 SIA 18
7.0 Programming MenuTree (PROG/0) 19
8.0 MenuTree (CMND#,TEST, HISTORY,
DISABLE, DRILL) 21
9.0 Installation Guide for U.L.Listed Systems
22
9.1 D7024 U.L. Listings 22
9.2 Installation Considerations 22
9.3 Programming the D7024 22
9.4 Reversing Modules 22
Appendix A: Abbreviations on Panel Dis-
play 23
Appendix B: Defaults for PROG/0 24
Index 26
D7024 ReferenceGuide Copyright© 1997Radionics,Inc. Page 3
FCC Compliance Notice
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules.These limits are designed
to provide reasonable protection against harmful
interference in a residential installation.This equip-
ment generates, uses and can radiate radio frequency
energy and if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on,
the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and
the receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is con-
nected.
• Consult the dealer or an experienced radio/TV
technician for help.
FCC Phone Connection to Users
This control complies with Part 68 of the FCC rules.
On the inside of the enclosure is a label that contains,
among other information, the FCC Registration
Number and the Ringer Equivalence Number (REN)
for this equipment.You must, upon request, provide
this information to your local telephone company.
The REN is useful to determine the quantity of
devices that may be connected to your telephone line
and still have all of those devices ring when your
telephone number is called. In most, but not all
areas, the sum of the REN's of all devices connected
to one line should not exceed five (5.0).To be certain
of the number of devices that you may connect to
your line, you may want to contact your local tele-
phone company to determine the max. REN for your
local calling area.
This equipment may not be used on coin service
provided by the telephone company.This control
should not be connected to party lines.
Should this equipment cause harm to the telephone
network, the telephone company may discontinue
your service temporarily. If possible, they will notify
you in advance. But if advanced notice isn’t practical,
you will be notified as soon as possible.You will be
informed of your right to file a complaint with the FCC.
The telephone company may make changes in its
facilities, equipment, operations, or procedures that
could affect the proper functioning of your equipment.
If they do, you will be notified in advance to give you
an opportunity to maintain uninterrupted telephone
service.
Notices
If you experience trouble with this equipment, please
contact the manufacturer for information on obtaining
service or repairs.
The telephone company may ask that you disconnect
this equipment from the network until the problem has
been corrected or until you are sure that the equip-
ment is not malfunctioning.The repairs to this
equipment must be made by the manufacturer and
not the user.
To guard against accidental disconnection, there is
ample room to mount the Telco jack to the inside of
the Control cabinet.
The operation of this Control may also be affected if
events such as accidents or acts of God cause an
interruption in telephone service.
Notice
The Industry Canada label identifies certified equip-
ment.This certification means that the equipment
meets certain telecommunications network protective,
operational, and safety requirements. Industry
Canada does not guarantee the equipment will
operate to the user’s satisfaction.
Before installing this equipment, users should ensure
that it is permissible to be connected to the facilities of
the local telecommunications company. The equip-
ment must also be installed using an acceptable
method of connection.The customer should be aware
that compliance with the above conditions may not
prevent degradation of service in some situations.
Repairs to certified equipment should be made by an
authorized Canadian maintenance facility designated
by the supplier. Any repairs or alterations made by the
user to this equipment, or equipment malfunctions,
may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the
electrical ground connections of the power utility,
telephone lines and internal metallic water pipe
system, if present, are connected together.
Caution: Users should not attempt to make such
connections themselves, but should contact the
appropriate electric inspection authority, or electrician,
as appropriate.
Page4 Copyright© 1997Radionics, Inc. D7024Reference Guide
1.0 Overview
1.1 System Overview
TheD7024 Control/Communicator isa fully integrated
hard-wire fire alarm system. It can support 4 input
points (expandable to 8) and 16 individual users.The
control panel has a built-in LCD keypad, however, up
to 4 additional keypads may be used to provide user
interface with the system and programming access for
the installer. The D7024 also includes the following
features:
• Built-in Dual-line Communicator
• Menu Driven Keypad Programming
• Freely Programmable Alpha Display
• 100 Event History Buffer
• 16 User Codes
• U.L. Listed, C.S.F.M. Approved
1.2 Specifications
1.2.1 Enclosure Housing
The standard enclosure is manufactured from 18
Ga., cold-rolled steel, and measures 15 in. Wide, by
20.75 in. High, by 4.25 in. Deep (38.1 cm Wide, by
52.7 cm High, by 10.8 cm Deep). A keyed lock is
included, and the LEDs and display are visible
through the door.
1.2.2 Temperature
• Storage and Operating Temperature:
+32° to +120°F (0° to +49°C)
1.2.3 Power
• Input Power:
120V, 60 Hz, 1.5 A (max.20 A fused)
• NotificationAppliance CircuitPower:
24VDC nominal, unfiltered(special application)
with up to 2.5 A capacity (but limited by overall
4.0 A capacity).Refer toTechnogram P/N 34950B
forcompatible devices
• Auxiliary Power:
24VDC nominal, unfiltered(special application)
Refer toTechnogram P/N 34950B
• Initiating Circuit (Smoke) Power:
24 VDC nominal
Refer to Technogram P/N 34445B
• Option Bus Power:
12 V +/- 5%, 500 mA
• OptionalStandby Batteries:
Two 12V (in series), 7 - 40 AH
1.2.4 Outputs
• 2 on-board notification circuits - NAC 1 and NAC 2.
These are 24V outputs for notification devices with
up to 2.5 A capacity (but limited by overall 4.0 A
capacity)on each circuit.
• Wired for standard Class B operation.
• Local Relays: The main panel includes two Form
“C” relays.The relay contacts are rated at 6 A,
24 VDC.No transient suppression or overcurrent
limiting are performed on the contacts of these
relays.The default selection for the relays is to
indicate general alarm and general system
trouble. By programming them to one or two of
the zone numbers described for point/zone
mapping, they can be programmed to activate on
a variety of conditions.
• Remote Relay Module (D7035): The D7035 is an
Octal Relay Module that provides 8 Form “C”
relay outputs. It connects to the D7024 via the
option bus. The outputs are fully programmable,
exactly as the local relays are programmed. Each
output operates independently of the other 7 to
provide complete flexibility. Communication with
the D7035 is supervised.
1.2.5 Points (Initiating Circuits)
All points work with 2 or 4-wire detectors.The
system has an optional alarm verification feature.
• Number of 2-wire Circuits:
4 circuits, expandable to 8
• Type of Circuit:
Class B, Style B
• End-of-Line Resistor:
2.21k ohms, P/N 25899 U.L. Listed
• Supervisory Current:
8 - 20 mA
• Required Current for Alarm:
25 mA
• Maximum Short Circuit Current:
44 mA
• Maximum Line Resistance:
150 ohms
• Circuit Voltage Range:
20.4 to 28.2 VDC
• Maximum Detectors per Point:
20 detectors (2-wire)
• Total Detector Standby Current:
3 mA max.
• Response Time:
500milli-seconds and programmablefrom 1
second to 15 seconds.
D7024 ReferenceGuide Copyright© 1997Radionics,Inc. Page 5
1.0 Overview (continued)
1.2.6 Keypads
• Maximum # of keypads:
4 D7033 keypads
• Maximumwire lengtheach:
1000 feet
• Maximum wire length total:
4000 feet in system
• Wire type:
4 conductor, unshielded, #22 AWG (0.8 mm)
“Telephone quad” or #18 AWG (1.0 mm) quad
wiring can be home-run or daisy-chained.
Note: No more than 2 keypads recommended on
any 1000 foot run.
Note: Shared cable is not recommended for
keypad,multiplex, options bus,telephone, or
sirenwiring.
1.2.7 Communicator
Willreport totwo (2)phone numberswith fullsingle,
double,and back-upreporting.Communicates in SIA,
Contact ID, BFSK, and 4/2Tone burst formats.
1.2.8 Users
The system allows up to 16 individual users. Each
user can have his own PIN number (the 4 digit code
entered at the keypads) and his own authority level
(to determine which functions he may perform).
1.2.9 Lightning Protection
MOVs and spark gaps provide protection from
lightningsurges andstatic discharges.
1.2.10 BackupBattery Calculation
• The following table is used to calculate the standby battery capacity required by NFPA when using the D7024:
1.2.11 StandbyCurrent Load
• Battery AH - (20% Storage + 0.375 AH's Alarm)
• The following table is the derated battery divided by hours minus the control standby (175 mA):
Page6 Copyright© 1997Radionics, Inc. D7024Reference Guide
2.0 Enclosure Installation
The D7024 control/communicator and the enclosure are
shipped together.The control, however, still needs to be
installed into the enclosre. Hardware for mounting the
enclosure to a wall, and the control to the enclosure is
located in the hardware pack.
2.1 Install the Enclosure
• Use the enclosure as a template and mark the top
mounting holes on the mounting surface.
• Pre-start the mounting screws for these two holes.
Slide the enclosure onto these mounting screws so
that the screws move up into the thinner section of
the holes.Tighten the screws.
• Screw in the remaining two screws in either set of
bottom mounting holes.
• Knock out the desired wire entrances on the enclo-
sure.
2.2 Install the Control/Communicator
CAUTION: The control is static sensitive. Make sure
you touch ground before handling the
control.This will discharge any static
electricity in your body.Example: Run the
ground wire to the enclosure before
handling the control.Then keep holding the
ground wire while installing the control.
• Insert the two support posts into the control retainer
holes as shown in the diagram below.
• Press the 1/8" nylon standoffs into the control
retainer holes as shown.This provides support
behind the control.
• Slide the top of the control into the retainer tabs (the
slots under the top of the frame).
• Once in the retainer tabs, the control will rest on the
two support posts.
• Secure the bottom of the control by screwing the 2
bottom corners through the support posts and
through to the control retainer holes.
CAUTION: Once the control is installed, be sure to
connect the supplied ground wire between
the door and the enclosure using the
supplied nuts.
D7024 ReferenceGuide Copyright© 1997Radionics,Inc. Page 7
3.0 Control Terminal Wiring
Page8 Copyright© 1997Radionics, Inc. D7024Reference Guide
4.0 System Worksheet
Account Number_______________Information
Name_______________________________________ Contact Person___________________________________
Address_____________________________________ Voice Phone Number_______________________________
_____________________________________ Panel Phone Number_______________________________
City, State, Zip_______________________________ Panel Answers Phone After [ ] Rings
Equipment Location and Notes
ACVoltage__________VAC Battery Voltage__________VDC AUX Current__________mA
Control Panel__________________________________________________________________________________________
Telephone Jack________________________________________________________________________________________
Telephone On Same Line as Panel_________________________________________________________________________
Earth Ground Connection________________________________________________________________________________
Notification Appliances__________________________________________________________________________________
Initiating Devices______________________________________________________________________________________
Miscellaneous Notes
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
D7024 ReferenceGuide Copyright© 1997Radionics,Inc. Page 9
4.0 System Worksheet (continued)
Personal Identification Numbers
Example
PIN Number Authority Level Name
User 00 1001 3 Henry M. Jones
PIN Number Authority Level Name
User 00
User 01
User 02
User 03
User 04
User 05
User 06
User 07
User 08
User 09
User 10
User 11
User 12
User 13
User 14
User 15
Page10 Copyright© 1997Radionics, Inc. D7024Reference Guide
4.0 System Worksheet (continued)
Keypad Location
Keypad #1 __________________________________________
Keypad #2 __________________________________________
Keypad #3 __________________________________________
Keypad #4 __________________________________________
Point Location and Notes
Example
Device(s) Location(s) Type
Point 1 Smoke Detector Hallway Fire, Alarm on Short, Latching, Verification
Device(s) Location(s) Type
Point 1
Point 2
Point 3
Point 4
Point 5
Point 6
Point 7
Point 8
Autres manuels pour D7024
2
Table des matières
Autres manuels Radionics Alarme incendie
