RadioLink T8fb Manuel utilisateur

RadioLink Electronic Ltd

www.radiolink.com

T8FB

(FHSS)

INSTRUCTION MANUAL

Compatible with Helicopter/Fixed Wing/Multicopter/Car/Boat

CE FCC RoHS

*Please be kindly noted that this manual will be updated regularly and please visit Radiolink official website to

download the latest version.

RadioLink Electronic Ltd

www.radiolink.com

Thank you for purchasing Radiolink 2.4 GHz remote control system T8FB .

To fully enjoy the benefits of this product and ensure safety, please read the manual carefully and set up

the device as instructed steps.

If any problems found during the operation process, either way listed below can be used as online tech

support.

1. Send mails to after_service@radioLink.com.cn or after_service1@radioLink.com.cn and we will

answer your question at the earliest.

2. PM us on our Facebook page or leave comments on our Youtube page

3. If the product is purchased from RadioLink AliExpress Global or Amazon U.S , you can contact after-

sales service directly.

4. If the product is purchased from the local distributor, you can also ask them for support and repair as

prefer.

All manuals and firmwares are available on RadioLink official website www.radiolink.com and more tutorials

are uploaded. Or follow our Facebook and Youtube homepage to stay tuned with our latest news.

SAFETY PRECAUTIONS

Never operate your model during adverse weather conditions. Poor visibility can cause disorientation and

loss of control of your model.

Never use this product in a crowd and illegal area.

Always ensure the trim levers at 0 and battery properly charged before connecting the receiver.

Always check all servos and their connections prior to each run.

Always be sure about turning off the receiver before the transmitter.

WARNING

This product is not a toy and is NOT suitable for children under the age of 18. Adults should keep the

product out of the reach of children and exercise caution when operating this product in the presence of

children.

Water or moisture may enter the transmitter inside through gaps in the antenna or joystick and cause

model instability, even out of control. If running in the wet weather(such as game) is inevitable, always use

plastic bags or waterproof cloth to cover the transmitter.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1This device may not cause harmful interference, and

2This device must accept any interference received, including interference that may cause undesired

operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

RadioLink Electronic Ltd

www.radiolink.com

CONTENTS

Part 1 INTRODUCTION OF T8FB SYSTEM...................................................................................................................1

1.1 T8FB Introduction..................................................................................................................................................1

1.2 Guidelines to mount the servos, receiver and battery ................................................................................... 2

1.3 Compatible Receivers : R8EF and R8FM ........................................................................................................ 3

1.4 Transmitter Calibration......................................................................................................................................... 5

Part 2 Firmware Upgrade................................................................................................................................................... 6

2.1 Firmware Introduction..........................................................................................................................................6

2.2 Upgrade Steps......................................................................................................................................................6

PART 3 T8FB Parameters Setup via Android Smart-phone APP............................................................................... 8

3.1 Configuration........................................................................................................................................................ 8

3.2 APP Installation.................................................................................................................................................... 8

3.3 Connection Steps.................................................................................................................................................8

3.4 The Functions Introduction.................................................................................................................................9

3.4.1 Setting Buttons Introduction.................................................................................................................... 10

3.4.2 Four Interface Introduction...................................................................................................................... 10

3.5 FAQ......................................................................................................................................................................14

Part 4 T8FB Parameters Setup via Computer............................................................................................................. 16

4.1 Parameter Configuration Software Setup Steps .........................................................................................16

4.2 Software Interface Introduction........................................................................................................................17

4.2.1 BASIC MENU........................................................................................................................................... 18

4.2.2 ADVACNE MENU.................................................................................................................................... 19

RadioLink Electronic Ltd

www.radiolink.com

Part 1 INTRODUCTION OF T8FB SYSTEM

1.1 T8FB Introduction

1) One two-way switch, one three-way switch, two VR switches, four trimmers, two sticks.

2) The picture below is mode1, SwB is default to control CH5, VrB is default to control CH6, SwA is

default to control CH7 and VrA is default to control CH8.

3) Universal JST battery connector supports multiple batteries, include 4pcs AA batteries or 2S to 4S

LiPo battery.

4) Defaulted low battery alarm voltage can automatically match 2S and 3S LiPo battery or 4pcs AA

batteries, can setting in the T8FB configure software.

3S LiPo battery: default low voltage alarm to 11.0V automatically after detection, you can setup low battery

voltage alarm from 10.0V to 12.5V.

2S LiPo battery: default low voltage alarm to 7.3V automatically after detection, you can setup low battery

voltage alarm from 7.0V to 8.9V.

4 pcs AA Ni-MH battery: default low voltage alarm to 5.0V automatically after detection, you can setup low

battery voltage alarm from 4.0V to 6.4V.

（MODE 1）

RadioLink Electronic Ltd

www.radiolink.com

1.2 Guidelines to mount the servos, receiver and battery

•Make certain the alignment tab on the battery, switch and servo connectors is orient correctly and

‘key’ into the corresponding notch in the receiver or connectors before plugging them in.When unplugging

connectors, never pull on the wires. Always pull on the plastic connector instead.

•Receiver’s Antenna: In generally receiver’s antenna is longer than remote control,don’t break or

retract it,otherwise shorten the control distance.The antenna must be kept away from conductive

materials,such as metal. Please make distance test before flying.

•If your aileron servos are too far away to plug into the receiver,use an aileron extension cord to extend the

length. Avoid plugging multiple extensions together to obtain your desired length. If the distance is greater

than 50cm or high current draw servos are being used, use heavy servo extensions.

•Receiver Vibration and Waterproofing: the receiver contains precision electronic part.Be sure to avoid

vibration,shock,and temperature extremes. For protection, wrap the receiver in foam rubber or other vibration-

absorbing materials. It is also a good idea to waterproof the receiver by placing it in a plastic bag and securing

the open end of the bag with a rubber band before wrapping it with foam rubber. If you accidentally get

moisture or fuel inside the receiver,you may experience intermittent operation or a crash. If in doubt, please

contact Radiolink after-sales or distributors for service.

•Always mount the servos with the supplied rubber grommets. Don’t over tighten the screws. No part

of the servo casing should contact the mounting rails, servo tray or any part of structure. Otherwise vibration

will be transmitted to the servo causing damage of servo. Note the small numbers (1,2,3,4) molded into each

arm on the servo arms. The number indicate how many degrees each arm is ‘off’ from 90 degrees to correct

for minute manufacturing deviations from servo to servo.

Port for trainer cable/

simulator/firmware update

RadioLink Electronic Ltd

www.radiolink.com

To center the servos, connect them to receiver and turn on the transmitter and receiver. Center the trims on

the transmitter, then find the arm that will be perpendicular to the push rod when placed on the servo.

After the servos are installed, operate each servo over its full travel and check that the push rods and servo

arms don’t bind or contact each other. Also make sure the controls do not require excess force to operate. If

there is an objectionable buzzing sound coming from a servo, there is probably too much resistance in the

control. Find and correct the problem. Even there is no servo damage, excess battery drain will result.

•Use the mouthing plate from the receiver on/off switch as a template for the cutout and screw holes, mount

the switch on the side of the fuselage opposite the engine exhaust, and where it won’t be inadvertently turned

on or off during handling or storage. Be certain the switch moves without restriction and ‘snaps’ from ON to

OFF, and that the cutout allows full motion of the switch in both directions.

•When install the switch harness to the helicopter, please use the switch cover. Generally sandwich the frame

between the switch and switch cover and securely tighten the screws. Different models might require different

installations. If so, please follow the model’s instruction manual.

• To prevent the servo lead wires from being broken by vibration during flight, provide a slight amount of slack

or extra so that the wire sticks out slightly and fasten it at suitable points. In addition, periodically check the

wire during daily maintenance.

1.3 Compatible Receivers : R8EF and R8FM

Radiolink T8FB is sells with 2.4G 8 channels receiver R8EF. R8EF is support S-BUS , PPM and PWM signal

working at the same time.

Specification:

1) Channels: 8 channels

2) Working voltage: 4.8-10V

3) Working current: 30mA（input voltage:5V）

4) Size: 48.5*21*11mm

5) Weight: 7g

6) 2048 section precision, 0.5us per section, servo anti-shake rudder.

7) Control distance: about 500m ground and 1000m air, actually

control distance depends on the environment.

RadioLink Electronic Ltd

www.radiolink.com

Signal Working Mode

(1) PWM Working Mode: Receiver indicator is RED with all 8 channels output PWM signal.

(2) SBUS/PPM Working Mode

Receiver indicator is Blue(Purple) with 8 channels output in total. Channel 1 is SBUS signal, channel 2 PPM

signal and channel 3 to 8 PWM signal.

S-BUS&PPM and PWM signal change:

Short press the ID SET on the receiver twice within 1s to switch the SBUS/PPM signal to PWM signal. When

the RED LED is on, signal output is PWM. When both RED and BLUE LEDs are on. Signal output is

SBUS&PPM.

MINI Receiver R8FM

T8FB is also compatible with 2.4G 8 channels supper mini receiver R8FM, which support S-BUS and PPM

signal working at the same time, supper mini size, is designed for racing drone.

CH8 (AUX)

CH7 (AUX)

CH6 (AUX)

CH5 (AUX)

CH4 (RUDD)

CH3 (THRO)

CH2 (ELEV)

CH1 (AILE)

Antenna

Binding Button (ID SET)

LED

Binding Button(ID SET)

CH8 (AUX), PWM

CH7 (AUX),PWM

CH6 (AUX),PWM

CH5 (AUX),PWM

CH4 (RUDD),PWM

CH3 (THRO),PWM

PPM

SBUS

LED

Antenna

RadioLink Electronic Ltd

www.radiolink.com

Specification:

1) Channels: 8 channels

2) Working voltage: 4.8-6V

3) Working current: 30mA（input voltage: 5V）

4) Size: 16.0*21.5*1.0mm

5) Weight: 2.5g

6) 2048 section precision, 0.5us per section, servo anti-

shake rudder.

7) Control distance: about 500m ground and

1000m air, actually control distance depends on the

environment.

S-BUS&PPM and PWM signal change:

Short press the ID SET on the receiver twice within 1s to switch the SBUS to PPM signal. When the RED LED

is on, PPM signal is output while SBUS signal is output when BLUE/PURPLE LED is on.

How to bind receiver to transmitter:

1. Put the transmitter and the receiver close to each other within 50 centimeters.

2. Power on T8FB and receiver R8EF(or R8FM). The RED LED will start flashing slowly.

3. Turn on T8FB and it will automatically bind to the closest receiver.

4. There is a black binding button (ID SET) on the side of receiver. Press the button for more than 1 second

and release, the RED LED will flash quickly, meaning binding process is ongoing.

5. When the RED LED stops flashing and is always on , binding is complete.

6. Make sure servos connected with the receiver can be operated by the transmitter.

Note of receiver usage：

1. Keep antennas as straight as possible, or the effective control range will reduce.

2. Big models may contain metal parts that influence signal emission. In this case. antennas should be

positioned at both sides of the model to ensure the best signal status in all circumstances.

3. Antennas should be kept away from metal conductor and carbon fiber at least half inch away and no over

bending.

4. Keep antennas away from motor, ESC or other possible interference sources.

5. Sponge or foam material is advised to use to prevent vibration when installing receiver.

6. Receiver contains some electronic components of high-precision. Be careful to avoid strong vibration and

high temperature.

7. Special vibration-proof material for R/C like foam or rubber cloth is used to pack to protect receiver.

Keeping the receiver in a well sealed plastic bag can avoid humidity and dust, which would possibly make the

receiver out of control.

1.4 Transmitter Calibration

Press rudder trimmer left and turn on transmitter at the same time,

When the transmitter is power-off, toggle both sticks at the central point. Then press the rudder trimmer button

left and the power button simultaneously,red and green LED will start flashing and the T8FB is ready to be

calibrated..

RadioLink Electronic Ltd

www.radiolink.com

Range Calibration: Toggle both sticks (Ch1-4) to the highest point/maximum and the lowest point/minimum.

Then back to the central point. (Refer to image below)

Center position calibration: Put stick to the center position, press rudder trimmer right, and then red and

green LED always on means sticks calibrate successful.

Part 2 Firmware Upgrade

Connect T8FB to a computer with an android USB cable, then setup parameters as you need.

Upgrade firmware by a USB cable helps T8FB always keeps the most advanced system and program. The

USB data backup copy function of T8FB helps save and copy parameter settings easily.

2.1 Firmware Introduction

The latest firmware is T8FB_FHSS_V201_a77b_20170609_33bit.

We will upgrade firmware according to T8FB users, new firmware will not upgrade in this manual, you can

download it from our website: www.radiolink.com

2.2 Upgrade Steps

(1) Download the divers that T8FB upgrade need from our website: http://radiolink.com.cn/doce/t8fb-upgrade-

info.html

(2) Open file“T8FB”.

(3) Choose COM, and click “Connect” and then turn on T8FB in 1 second.

(4) “Disconnect” will change to “Connected” and the color of word will from red to green if connect

successfully.

RadioLink Electronic Ltd

www.radiolink.com

(5) Choose “APROM” and then choose the firmware T8FB_FHSS_V201_a77b_20170609_33bit

(6) Click “Start”, the progress bar will turn to green, upgrade successful if remind “PASS”.

Autres manuels pour t8fb

Table des matières

Autres manuels RadioLink Télécommande

RadioLink

RadioLink AT9 Manuel utilisateur

RadioLink

RadioLink TrackStar D-Spec TS4G Manuel utilisateur

RadioLink

RadioLink AT9S PRO Manuel utilisateur

RadioLink

RadioLink t8fb Manuel utilisateur

RadioLink

RadioLink T8S(BT) Manuel utilisateur

RadioLink

RadioLink RC8X Manuel utilisateur

RadioLink

RadioLink RL036T-001A Manuel utilisateur

RadioLink

RadioLink T8S Manuel utilisateur

RadioLink

RadioLink T8S Manuel utilisateur

RadioLink

RadioLink T8S Manuel utilisateur

RadioLink

RadioLink RC4GS V3 Manuel utilisateur

RadioLink

RadioLink RC4GS V2 Manuel utilisateur

RadioLink

RadioLink t8fb Manuel utilisateur

RadioLink

RadioLink Ei 411 Manuel utilisateur

RadioLink

RadioLink t8fb Manuel utilisateur

RadioLink

RadioLink T4EU Manuel utilisateur

RadioLink

RadioLink T7F-2.4Ghz Manuel utilisateur

RadioLink

RadioLink AT10II Manuel utilisateur

RadioLink

RadioLink RC8X Manuel utilisateur

RadioLink

RadioLink RC6GS V3 Manuel utilisateur

RadioLink

RadioLink RC6GS Manuel utilisateur

RadioLink

RadioLink RC4GS V3 Manuel utilisateur

RadioLink

RadioLink RC6GS V2 Manuel utilisateur

RadioLink

RadioLink RC6GS V3 Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation