RadioLink RC3S Manuel utilisateur
Digital 4-Channel Proportional RC System
Instruction Manual
RadioLink Electronics Co., Ltd
Http://www.radiolink.com.cn
CE FCC ROHS
*.This manual also appllies to RC4G
1
1. Introduction and service………………………………………………………….2
2. Safety guides……………………………………………………………….....…. 2
3. Battery recharge notice……………………………………………………..….…3
4. Contents and specifications………………………………………………..…..….4
5. Receiver installation and binding…………………………………………………5
7. Display when power switch turned on…………………………………….……...7
8. Language Select "LANGUAGE"………………....……………………………......9
9. Model Select "MODEL"………………………………………………...................9
10. End Point Adjuster "EPA"………………………………….…..…..…………...…10
11. Steering EXP "STEXP"…………………………………….………..……………..11
12. Steering Speed "STSPD"……………………………………. .….…………..…......12
13. Throttle EXP "THEXP"…………………………………………………………......13
14. Throttle Speed "THSPD"………………………………………………………........15
15. A.B.S. Function "A.B.S"………………………………………………….................17
16. Throttle Acceleration "ACCEL"…………………………………………………......22
17. Idle-Up "IDLUP"…………………………………………………………........…....23
18. Subtrim "SUBTR"…………………………………………………………..……....24
19. Servo Reverse "REV"……………………………………………………….....…....25
20. Steering Dual Rate/Throttle Dual Rate "D/R"………………………………...……...26
21. ATL Function "ATL"………………………………………………………...……..27
22. Programmable Mixes "PMIX"………………………………………………..…......27
23. Channel 3 Position "AUX"………………………………………..……………...30
24. Model name "NAME"…………………………………………………….…......30
25.Low voltage alarm……………………………………………………...………. ...31
26. Reset function "RESET"……………………………………………………...…....31
MENU
6.Usage method of receiver intergrated with gyro and settings............................................6
Usage method of receiver intergrated with gyro and settings........................................6
6 .
2
Thank you for choosing RadioLink RC system, if you are the first time to use
this type of products, please read this statement carefully and strictly in accordance
with the requirements of operation. You could refer to the Manual if you meet any
problems during the operation . Please well keep the manual after use because you
might have to use it again next time.
If you found any problems during the operation process, please refer to the
manual. If the problem still exists, you could contact our dealers to find out the way to
solve it. And you could also log on our website for service:
Http://www.radiolink.com.cn
Important Safety Notice：
The following two symbols will appear in this manual（please pay attention to
the paragraph with this two symbols labeled）：
Prohibition Testing and confirmation
Do not use in bad weather such as rainy or thundering to assure the safety of
you and others.
Forbid to use this product in the crowd and the place against national law!
You need to turn the throttle channel(ch3) and inch switch to the lowest
before you use. Then switch on the transmitter, finally connect the receiver.
Before using, please make sure the movements of servo are corresponding
with the direction of joystick. If inconsistent, please adjust them before using.
Safety guides
Introduction and Service
3
The sequence to shut down is that turn off the receiver power first, and then
shut down the transmitter. If the above operations are reverse, it might lead to
uncontrolled situation and cause accidents
The transmitter needs to be powered by 4 AA alkaline 5# batteries or Ni-MH
batteries. Please check the voltage of batteries before using, as it might lead to
uncontrolled situation and accidents when the voltage is lacked. So you must change
the battery or recharge them in time.
Recharge steps：
A. Install the batteries to transmitter with correct directions, and cover it.
B. Connect the charger to the main connector.
C. Connect the charger to the transmitter charging port.
D. Cut off the power supply immediately while recharging completed.
Warning: Don’t try to charge to one-off dry batteries, avoiding a fire, explosion or
other severe consequence.
If you are using a nickel-cadmium, nickel-metal hydride batteries for recharging,
please use our company dedicated charger(optional accessory). If the electrical
current is too large and it might lead to overheated and cause a burning accident.
Please cut off the power supply immediately after recharging. Please take out the
batteries from the transmitter when you are not using it within a period, because the
battery might damage the battery connection metal flake, thus cause bad connection.
Above safety notices must be complied strictly, our company will not be
responsible for any damage caused by the behaviors forbidden in above notices.
Battery recharge notice
106mm
4.6-10
4
Contents and Specifications：
Contents：
1.Antenna 2.Binding key
3.Channel connection pin
Specs：
Size：51.5*24*15（mm）
Channel number：4 channels
Power standard：V
Frequency：2.4GHz Weight：5g
Contents：
1. Antenna
2. LCD
3. Menu key
4. Turning wheel
5. Function key A throttle
6. Function key B Direction
7. Function key C the 3rd channel
8. The 3rd/4rd channel VR
9. The 3rd/4rd channel button
10. Recharge connection slot
11. Throttle trigger
12.Simulator port
13.Power switch
14. USB hardware upgrade port
Specs：
Size：213*117*115.5(mm)
Antenna length：
Weight：420g
Channel number：4 channels
LCD：128*64 lattice（with backlight）
Contents and specifications
range,
5
Power standard：6VDC (1.5AA*4)
RF power：less than 10dbm
Power extending: JST port 2S~3S
LiPo/LiFePo battery
Modulation: FHSS
Low voltage alert：Yes（lower than 4.6V）
Data resolution：2048
Frequency：2.4GHz
RF range: 300meters on ground
Failsafe: in 1 second receiver fail getting signal from TX, the throttle will be 0, servos
keep the last status.
Receiver’s connection and installation：（such as some car model）
Rudder Servo(CH1)
Throttle
Servo(CH2)
Servo(CH3)
Servo(CH4)
NOTICE：
1．Confirm battery, switch, servos and etc are connected with receiver right.
2．While installing servos, please keep servo’s distance from model body,
otherwise the vibration can lead to servo and make servo damaged.
3．After installation of servos, please try to control the servo to full if it
got stuck or sounded abnormal, you must solve the problem. Even if servo
Receiver installation and binding
* RC3S standard equipment:A transmitter and a R4EH-H receiver.
* RC4G standard equipment:A transmitter and a R4EH-G receiver.
6
was not damaged, large circuit occurred.
4．Do not cut off or bind the receiver antenna, and try the best to keep it
far
away from metal and carbon graphite material.
5．Receiver is made up from precise electronic components, it need to
be
protected from vibration by packaged with sponge or other shock
absorption materials.
Code-matching method between transmitter and receiver:
1．Load the battery into transmitter, power on it.
2．Connect the power to the 2nd Channel pin of receiver.
3．Press the binding button on the receiver till LED starts twinkling.
4．LED stops the twinkle, bright light indicates a successful
code-matching was completed.
Display when
power
on
R4EH-G is intergrated with gyro,it can make cars run stablely,
the effect is more obvious
when the car is turning.
The gyro function can be set "ON"and "OFF"
Description of indicator light:
1.Receiver in normal working condition:Green light on
2.Gyro in working normal condition:Red light on
Attention:The gyro function was set to on by factory.
When the receiver is in working condition
At this time,
the red light flashing,the gyro enter a self-examination state.
please keep the
receiver in a stable condition.
In normal condition, the direction of cars including forward and backward.
Method of using receiver intergrated with gyro
The gyro should
only work in forward direction.
only when choosing the correct direction,can the gyro really work.
Attention:The vehicle gyro has the phase adjusting function,
Gyro function settings:
1.Usage method of gyro:Short press the code key for three times(time interval
between
each time lasts less than 1 second ), the red light continuous flashing three times, then
the red light into a lasting bright, it shows the gyro in a normal state.
2.The gyro sensitivity:The default is three channel.
The VR switch can be used for real-
time adjustment when the radio control works,to ensure that the third channel VR
control
(Factory default)
clockwise, the sensitivity increases, counterclocwise, the sensitivity decreases.
Attention:Sensitivity shuoldn't be set to 0.
powered
button twice, the
phase correction is completed.
press code
In this situation, short
When to the right,wheel left correction.
When rotating the car to the left,wheel
to observe whether the gyro is correcting wheel.
turn around the car
forward direction. , then the
code button for once(less than 1 second),
, then gyro works in backward direction.
engine doesn't move
release the accelerator
the
3.Gyro usage method in forward and backward direction:
When gyro in working state, pull
remote acceleraterto keep the car move forward for a distance,
in the premise of not playing the direction key,
turn around the
car body,
You need
the right light flashes once
4.Gyro phase adjustment:When the gyro works in forward direction,
if the steering
to short press the
gyro works in
Receiver
Battery
voltage
Model name
display R/C
control
system name
Steering trim display
Throttle trim display
Display when power switch turned on
7
LCD Screen
When you power on the transmitter, LCD screen shows
battery
voltage,
R/C
control
system
name, model name,
steering
trim,throttle trim
Model Name
can store the data for 10 models, model name will show on the LCD when
you power on the transmitter. Please make sure the model name the screen displayed
is the right what you want. If the model name you chose is not corresponding with
your model, the pre-settings should be wrong.
Transmitter battery voltage
In addition to the model#, LCD can show the voltage of battery. When the
voltage is lower than 4.6V, it would start the low-voltage alert, it would send out
“BeBe…” sounds, till the transmitter is power-off. When you hear the low-voltage
alert, you have no more than 4 minutes for controlling your model, please safely stop
your model before the uncontrolled situation. Please make sure the battery voltage is
higher than this voltage data while radio controlling.
Transmitter function menu setting
When you want to browse or change a setting of transmitter, you should go into
function menu setting mode. Under function menu setting mode, you can set up
Language Select "LANGUAGE", Model Select "MODEL",End Point Adjuster "EPA",
Steering EXP "STEXP",Steering Speed "STSPD",Throttle EXP "THEXP",Throttle
Speed "THSPD",A.B.S. Function "A.B.S",Throttle Acceleration "ACCEL",Idle-Up
"IDLUP",Subtrim "SUBTR",Servo Reverse "REV",Steering Dual Rate/Second
Dual Rate "D/R",ATL Function "ATL",Programmable Mixes "PMIX", Auxiliary
Channel 3 and 4 "AUX"，Model name "NAME", Reset function "RESET".
,the red light flashes two times
The system
8
system,
9
Both English and Chinese version menu are available for which is convenient
for Chinese and English-speaking players to personalize function menus.
1. Access the function menu (By pressing “Exit” and “Enter” buttons simultaneously
and holding them down for one second), the Language select function will be chosen.
2. Press “Enter” button to get into “LANGUAGE” function
interface。
3. Use“Dec(-)”or “Inc(+)”key to select“中文”or
“English”,the selected language will be with black
shading effect.
4. Press “Enter” button, the desired language is selected,
and return to the initial screen automatically.
The transmitter can store model memories for ten models. Use this function to
call a new model #.
MODEL- Model select function
1. Access the function menu (By pressing “Exit” and
“Enter” buttons simultaneously and holding them down for
one second ), press “Enter” key once, the Model select
function will be chosen.
2.Press “Enter” button, the current active model will be
blinking.
3.To activate a different model# by pressing “Dec(-)” or “Inc(+)” button until the
desired model# blinks.
4.Press “Enter” button, the selected model# stops blinking, now the model# has been
selected.
5. Return to the initial screen by pressing “Exit” button twice.
Model Select "MODEL"
Language Select "LANGUAGE"
Table des matières
Autres manuels RadioLink Contrôleurs
RadioLink
RadioLink Byme-DB Manuel utilisateur
RadioLink
RadioLink BYME-A Manuel utilisateur
RadioLink
RadioLink PIXHAWK Manuel utilisateur
RadioLink
RadioLink BYME-D Manuel utilisateur
RadioLink
RadioLink BYME-A Manuel utilisateur
RadioLink
RadioLink SE100 Manuel utilisateur
RadioLink
RadioLink BYME-D Manuel utilisateur
RadioLink
RadioLink T8S Manuel utilisateur
RadioLink
RadioLink Turbo PIX Manuel utilisateur
RadioLink
RadioLink BYME-A Manuel utilisateur
