Radio Shack Extra remote sensor Manuel utilisateur
Owner’s Manual
Please read before using this equipment.
Extra Remote Sensor
to 63-1030
63-1031.fm Page 1 Wednesday, June 28, 2000 10:25 AM
2
ˆ
Contents
Introduction ........................................ 4
Installing Batteries ............................ 5
Mounting the Sensor ........................ 8
Selecting a Location .................... 8
Using the Stand ........................... 9
On a Wall ................................... 10
Operation .......................................... 13
Changing the Display Channel ...... 13
Changing the Degree Format ........ 15
Resetting the Sensor ..................... 15
Care ................................................... 17
Specifications ................................... 18
©2000 RadioShack Corporation. All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
63-1031.fm Page 2 Wednesday, June 28, 2000 10:25 AM
3
FCC INFORMATION
This device complies with Part 15 of the
FCC Rules
. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference that
may cause undesired operation.
This equipment complies with the limits
for a Class B digital device as specified in
Part 15 of
FCC Rules
. These limits pro-
vide reasonable protection against radio
and TV interference in a residential area.
However, your equipment might cause
TV or radio interference even when it is
operating properly. To eliminate interfer-
ence, you can try one or more of the fol-
lowing corrective measures:
63-1031.fm Page 3 Wednesday, June 28, 2000 10:25 AM
4Introduction
• reorient or relocate the receiving
antenna
• increase the distance between the
equipment and the radio or TV
Consult your local RadioShack store if
the problem still exists.
ˆ
Introduction
Your RadioShack Extra Remote Sensor
is designed for use with the RadioShack
Wireless Indoor/Outdoor Thermometer
with Indoor/Outdoor Hygrometer system
(Cat. No. 63-1030). Installation is easy,
with no wires to connect. You can mount
the remote sensor outdoors or in another
room (away from the system’s main unit),
63-1031.fm Page 4 Wednesday, June 28, 2000 10:25 AM
5
Introduction
or use its supplied wire stand for easy
viewing on a table or desktop.
INSTALLING BATTERIES
Your sensor requires two AA batteries
(not supplied) for power. For the best per-
formance and longest life, we recom-
mend RadioShack alkaline batteries.
Cautions:
• Use only fresh batteries of the
required size and recommended
type.
• Do not mix old and new batteries,
different types of batteries (standard,
alkaline, or rechargeable), or
rechargeable batteries of different
capacities.
63-1031.fm Page 5 Wednesday, June 28, 2000 10:25 AM
6Introduction
Note: If you expect to use the remote
sensor in temperatures below –4°F
(–20°C), we recommend you use lithium
batteries.
Follow these steps to install batteries.
1. Use a Phillips screwdriver to remove
the screws in the battery compart-
ment cover, then lift off the cover.
2. Set CHANNEL and °C/°F inside the
compartment to the desired set-
63-1031.fm Page 6 Wednesday, June 28, 2000 10:25 AM
7
Introduction
tings. (See “Changing the Display
Channel” on Page 13 and “Changing
the Degree Format” on Page 15)
3. Place the batteries in the compart-
ment as indicated by the polarity
symbols (+ and –) marked inside.
4. Use a pointed object (such as a
straightened paper clip) to press
RESET and initialize the sensor’s
transmitter.
5. Replace the cover and secure it with
its screws.
When appears (on either the sensor
or under the sensor’s channel number on
the main unit) or the sensor stops operat-
ing properly, replace the batteries.
63-1031.fm Page 7 Wednesday, June 28, 2000 10:25 AM
8Introduction
Warning: Dispose of old batteries
promptly and properly. Do not burn or
bury them.
Caution: If you do not plan to use the
sensor for a week or longer, remove the
batteries. Batteries can leak chemicals
that can destroy electronic parts.
MOUNTING THE SENSOR
You can place the remote sensor on a flat
surface, or mount it on the wall using
screws (not supplied) and the supplied
bracket.
Selecting a Location
Choose a location for the remote sensor
that is within about 328 feet (100 m) of
the main unit. The remote sensor can be
placed either indoors or out.
63-1031.fm Page 8 Wednesday, June 28, 2000 10:25 AM
9
Introduction
The construction of your home or office
might affect the transmission range be-
tween the main unit and the remote sen-
sor. If you have a choice of several
locations, try each to see which provides
the best performance.
Caution: Do not place the remote sensor
where it will be:
• in direct sunlight
• in water (it is weather-resistant, not
water-proof)
• near electrical appliances or heating
or air conditioning vents
Using the Stand
To set the remote sensor on a flat sur-
face, insert the ends of the supplied wire
63-1031.fm Page 9 Wednesday, June 28, 2000 10:25 AM
10 Introduction
stand into the holes on the back of the re-
mote sensor.
On a Wall
1. Drill two holes 13/4inches apart.
Then thread a screw into each hole,
letting the heads extend about 1/4
inch from the mounting surface.
63-1031.fm Page 10 Wednesday, June 28, 2000 10:25 AM
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Radio Shack Accessoires
Radio Shack
Radio Shack XMODS 60-439 Manuel utilisateur
Radio Shack
Radio Shack LX-3100 Manuel utilisateur
Radio Shack
Radio Shack 270-258 Manuel utilisateur
Radio Shack
Radio Shack XMODS Custom RC Manuel utilisateur
Radio Shack
Radio Shack XMODS Manuel utilisateur
Radio Shack
Radio Shack 2302019 Manuel utilisateur
Radio Shack
Radio Shack XMODS Custom RC Manuel utilisateur
Radio Shack
Radio Shack 61-140 Manuel utilisateur
Radio Shack
Radio Shack XMODS Custom RC Manuel utilisateur
Radio Shack
Radio Shack 63-1064 Manuel utilisateur
