Radial Engineering SDM BATTERY Series Manuel utilisateur
SDM BATTERY SERIES
70-2.000 Nm
NL
FR TURK POL
ENG DU RUS IT
DAN NOR
ES
USER MANUAL WWW.RADIALTORQUE.EU
Version 1.0 - August 2022 2
User manual SDM Battery Series
Table of contents
1. Before taking into use 3
2. Charging the ba ery 3
4
4
5
3. Safety 6
8
9
4. Accessories 9
5. Assembly 10
6. Movement of the reac� on arm 10
7. Using the tool 12
8. Torque adjustment 13
9. SDM Calibra� on 14
10. Preparing 16
16
17
17
11. Maintenance 18
12. Intended use 18
13. Warranty 18
14. Contact 19
Version 1.0 - August 2022 3
User manual SDM Battery Series
!
!
SDM Battery Series torque wrenches are reversible, non-impacting, torque controlled tightening tools and must
always be operated with the following:
• Fully charged battery
• Impact sockets with locking pin and o-ring
• Proper reaction arm with retaining ring.
1. General instruc� ons
2. Assembly
NOTE: Do not operate the tool before reading these instructions. If breakdown, malfunction or damage
occurs, do not attempt to repair, please contact Radial Torque Tools B.V. immediately.
1. Make sure the battery is fully charged.
2. Slide in the battery pack until it engages.
3. Fasten and secure the reaction arm on the jagged side of the gearbox with the retaining ring.
NOTE: These torque wrenches contain metal components that can be dangerous in hazardous areas.
Thank you for purchasing this ne Radial product! We highly recommend reading this user manual
thoroughly in order to understand all aspects of these tools. All tool features, our safety instructions and
tool maintenance are explained in detail.
Familiarizing yourself with all the ins and outs of this tool will ensure a long lifetime of the tool and a happy
operator.
On our website you can download the latest software for your Radial tool and you can nd additional
product information such as product videos. See: www.radialtorque.eu.
If you can have further questions, feel free to contact us by phone or e-mail.
Thank you,
The Radial Team
6. To remove the reaction arm,
place a screwdriver at the
beginning of the retaining ring
and spread the retaining ring
open. Then pull the retaining ring
o and remove the reaction arm.
5. Then gradually press the
retaining ring until it is completely
closed.
4. Spread the retaining ring open
with a screwdriver and place the
open side in the groove at the end
of the gearbox.
Introduction
Version 1.0 - August 2022 4
User manual SDM Battery Series
Step 1: Slide in battery Step 2: Go the password
screen
Step 3. Use password
"FFFF"
Step 4. Conrm password
with "ENTER
Step 8: Set angle and / or
torque
Step 7: Conrm choose
with "ENTER"
Step 6: Choose between
angle and torque
Step 5: Go to strategy
screen
Step 9: Use "DOWN" to
select value
Step 10: Save or cancel
settings
Step 11: Exit torque and / or
angle setting mode
Step 12: Tool is ready to
opperate
3. Seng Torque and / or Angle
F
-F
-F
-
4x
1
2
FFFF
1
2
OK
1
2
3x
11
2
3....
4x
2x
1
2
F F F
1x
2
1
3
Version 1.0 - August 2022 5
User manual SDM Battery Series
EXIT ENTER / EXITUP / DOWN / LEFT / RIGHT
There are four LEDs on the display module. 3 on the top and 1 below the display screen.
The Status LEDs shall be used as follows:
Red - The last tightening cycle exceeded its high limit.
Yellow - The last tightening cycle ended below its low limit.
Green - The last tightening cycle ended between its high and low limits.
Blue - The tool has an active fault condition.
4. LED lights explained
5. Screen explained (Advanched Series only)
5.1. Programming keys
The image below shows the screen of SDM Battery Series screen module with descriptions of the
programming keys.
Version 1.0 - August 2022 6
User manual SDM Battery Series
Angle Sets angle
Torque Sets torque
Clock wise To tighten the bolt
Anti clockwise To loosen the bolt
Unit of torque Indicates unit of the torque displayed
Target torque and angle Sets the torque and angle
Torque and angle high Sets the high torque and high angle
Torque and angle low Sets the low torque and low angle
Torque treshold The torque at which reading of the angle will be started
Free speed Indicates free speed of the SDM Battery tool
Shift down torque Indicates the shift down torque
Shiftdown speed Indicates shiftdown speed of the SDM Battery tool
Gang count
Shows the gang count number of bolts to be fastened
per group, gang, or set
Enable RF module Enables the RF module
Disable RF module Disables the RF module
Save changed settings Saves the changed settings
Ignore changed settings Ignores the changed settings
These values can be edited by entering “EDIT” mode and using “UP” and “DOWN” key.
5.2. Icon list
Version 1.0 - August 2022 7
User manual SDM Battery Series
5.3. Main screen
Pressing “ENTER” key after switching on the screen will show this image.
The PRIMARY SECTION - shows latest peak torque (for a torque strategy) or the latest peak angle (for an
angle strategy), with units.
The SECONDARY LEFT - shows the cycle count or gang count, if gang count is programmed.
The SECONDARY RIGHT - shows the active conguration number.
5.4. Conguration setting
This screen shows conguration setting used in the tool. Pressing “ENTER” will enable the edit mode.
“UP” or “DOWN” key can be used to update the conguration.
Pressing “ENTER” again will select the modied conguration.
!NOTE: Only Conguration 1 can be programmed through the display module.
Version 1.0 - August 2022 8
User manual SDM Battery Series
5.5. Password screen
The password screen shows whether the tool is locked or unlocked. If the tool is locked the parameters of
the SDM Battery Series cannot be edited.
Password can be entered by pressing the “ENTER“ key and using the “UP” or “DOWN” key.
!
!
To enter the Tool ID, use password “1234” and then press "LEFT"
To set torque and / or angle and to enable/disable RF, use
password “FFFF” and then press "RIGHT"
5.6. Tool ID and softeware information
The PRIMARY SECTION - shows the Tool Location ID.
The SECONDARY LEFT - shows the Motor Controller Firmware version.
The SECONDARY RIGHT - shows the screen Firmware version.
Press "DOWN" to display the tool time in HH:MM:SS format.
Press "DOWN" again to display a screen for internal use only to view log location.
Press "DOWN" again to display a second internal use only log screen.
Press "DOWN" again to return to the Tool ID screen.
Press "RIGHT" to exit back to the Main screen.
Version 1.0 - August 2022 9
User manual SDM Battery Series
5.7. Set torque and enable/disable RF
After screen is unlocked with a valid password, Pressing “RIGHT” key will allow you to set torque and / or
angle. See section 3. Setting Torque and / or Angle for more information.
This below screen allows the user to enable or disable the radio module. The selection on the left disables
the radio module and the selection on the right enables the radio module.
5.8. Gang count
The below screen shows the gang count number of bolts to be fastened per Group, Gang, or Set for
Conguration 1. This can be modied by entering edit mode.
5.9. Shiftdown speed
This screen indicates shiftdown speed of the SDM Battery tool. Shiftdown speed can be edited by
entering edit mode and updating using "UP" and "DOWN" key.
Version 1.0 - August 2022 10
User manual SDM Battery Series
5.10. Shiftdown point cong
This screen indicates “Torque Threshold for shiftdown point”.
This can be changed by entering edit mode and updating using “UP” or “DOWN” key.
5.11. Free Speed
The below screen indicates free speed of the SDM Battery tool.
The value can be edited by entering editmode and using “UP” and “DOWN” key.
5.12. Torque
Torque “LOW” screen
Torque "LOW", “HIGH” and "TARGET" can be modied by entering edit mode and using “UP and “DOWN”
key.
Torque “HIGH” screen Torque “TARGET” screen.
Table des matières
