Race RC Hover Jet VTOL Manuel utilisateur
ON/OFF
Power ON light
Install baeries in the transmier
Transmitter operation：
1.Use a screwdriver to open the battery compartment
2.Insert three AAA batteries, matching the polarities marked inside
3.Use a screwdriver to close the battery compartment.
1.Open the battery compartment and pull out the battery.
2. Insert the plug and install battery inside.
3.Close battery compartment.
Install the flight baery
LED
Charge the Li-Po baery：
1. Connect the included USB charging cable to the 3.7V 530mAh
Li-Po battery and a USB power source, such as a laptop. The
USB connector indicator red LED remains lit when charging
and turns off once battery is full charged. Charging time
is about 60 minutes.
2. Disconnect the USB charging cable when fully charged,
do not attempt to over charge.
Cauon：
· Use only the included charging cable to charge the flight
battery, other cable may damage the airplane
· Let the Li-Po battery battery cool down before re-charging.
Safety Warning:
• To ensure safety, parents should read this User’s Manual with children before use.
• To avoid injury, do not touch the product while flying or while the propellers are spinning.
• Be careful to keep your body and loose clothing away from the propellers and motors.
Do not modify or change this product without authorization.
Throle Steering
TURN
LEFT
TURN
RIGHT
ASCEND
DESCEND
MOVE
LEFT
MOVE
RIGHT
FORWARD
BACKWARD
360 Flip High/Normal/Low Rates
FORWARD TRIM
BACKWARD TRIM
LEFT TRIM
RIGHT TRIM
One buon take-off/landing
On/Off
Push
(Stunt mode)
Look for these other great products from Rage RC
at your local hobby retailer or online at ragerc.com
RGRB1100 Aqua Dart RTR Boat White/Green
RGRB1101 Aqua Dart RTR Boat White/Black
RGRA1106 X-Fly VTOL RTF Aircraft
RGR4500 Jetpack Commander RTF Quad-White
RGR4501 Jetpack Commander RTF Quad- Red
RGRC1800 R18MT Monster Truck RTR
4
!"#$%&'$(#) *#+,)-."-/0
!"!#$%& '()*+,*-./012.!03.45+6+78-
!"!#$%9
:+(;*<<*+.=*-.>#?@.'()*+,*-
!"!#$%A $=.BCD/.9B&E4F.25;(.G7--*+HI.'()*+,*-
!"!#$%D BCD/.9&&E4F.J=G.KF7+L*+@.'()*+,*-
!"!#$%M
0+7NOE5--*+@.'()*+,*-
at www.ragerc.com or call 1-800-622-7223 M-F 9:00-5:00PM Mountain Time
Spare Parts
Instruction Manual
Please read before use and retain for reference
1. Aer pairing, press the rates buon to switch between high rates (3 beeps) normal rates (2 beeps)
and low rates (1 beep). First flights should be in normal or low rates before advancing to high rates.
2. Press the buon with the One Buon Take-Off symbol the HoverJet will take off and hover at about 3’
above the floor.
3. Move the throle (le sck) upward and downward to control the ascent or descent, move the steering
(right sck) to control the flight direcon.
4. Move the throle (le sck) le or right and the HoverJet will rotate (yaw) le/right accordingly.
5. Press the One Buon Take-Off buon again or move the throle sck down gradually to land.
6. When your finished flying, turn off the HoverJet and the transmier.
Cauon：To avoid injury to the pilot or damage to the drone, move the throle smoothly and not too fast.
Flying Your HoverJet
The 4 propellers are not idencal. Each propeller
is labeled with an A or B.When installing replacement
propellers, be certain to insatll the A/B in the correct locaon.
IF needed, use pliers to gently pull the damaged propeller
off the sha.
Warning：To avoid damage to people or aircra, check
propellers for damage before
each flight. Also, ensure that the
propellers are firmly pressed on
to the sha. Replace any propeller
that shows damage and use only
the provided propellers or
idencal replacements. Do not
modify the provided propellers.
Replacing Damaged Propellers
• Do not dispose of the Li-Po baery into a fire.
• Never place the product on a hot surface.
• Keep the product in dry and cool environment.
• Use only provided USB cable for charging.
Charge the baery per the manual instrucons.
• Do not use type of sharp object to insert the Li-Po
baery to avoid puncture.
• Charge the Li-Po baery every 6 months if not in
regular use.
• Turn off the power when the product is not in use.
Warnings
Geng Ready to Fly
1. Press the On/Off buon unl the LED flashes.
2. Place the HoverJet on a level surface.
3. Press the On/Off buon of transmier,
the LED should flash and the transmier should beep.
4. Move the throle all the way up then back to middle
posion to pair the airplane and transmier. If pairing is
successful, the transmier will beep 2 mes and the LED on
both transmier and airplane stop flashing and remain on.
Note: If pairing fails, turn off airplane and transmier,
repeat above steps, or move to another place to avoid
electromagnec interference.
Calibrang Your HoverJet
1. Aer pairing, put the HoverJet on a level surface.
Move the throle sck down and the steering sck up
at the same me and hold them in place, the
LED’s should then flash on and
off for about three seconds.
2. When LED’s stop flashing
the calibraon is complete.
The HoverJet should now
maintain a steady hover and
fly smoothly. If not, the
controls need to be adjusted
using the trim buons- see that secon for instrucons.
Warning:
CHOKING HAZARD--
Small Parts Not For
Children Under 3 Years
Made in China
A
A
B
B
1. Press( ) button, the transmitter will beep constantly.
2. Move the steering (right stick) to perform flips.
⊙ Front Flip：Move the steering foward (up).
⊙ Back Flip：Move the steering backward (down).
⊙ Left Flip：Move the steering left.
⊙ Right Flip：Move the steering right.
3. After completing a flip, the HoverJet will exit flip stunt mode.
If you want to exit flip stunt mode afterpressing the button,
push in the throttle control stick.
Note：* To avoid hitting people or other objects, please ensure
there is enough space before performing flips.
Compleng Flips Trimming Your HoverJet
· Push the throle forward and observe how the
aircra reacts.
• Trim forward/backward: If the aircra tends to dri
forward, press( ) unl aircra hovers; if it tends to
dri backward, press ( ) unl aircra hovers.
• Trim le/right: If the aircra tends to dri le,
press ( ) unl aircra hovers, if it tends to dri le,
press ( )unl aircra hovers.
Note: The transmier beeps when you press a
trim control but stops beeping when you reach
maximum trim adjustment.
Hover Jet
32
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
