r.LiNK CI-RL3-R40 Manuel utilisateur
Version 16.03.2020 HW: CAM(V97)/(V30) CI-RL3-R40
r.LiNK Video-inserter
CI-RL3-R40
Compatible with
Opel vehicles with R4.0 IntelliLink system
and 7" monitor with DIN-cage attached
Video-inserter with 2 video inputs,
rear-view camera input and CAN control
Product features
Video-inserter for factory infotainment systems
2 CVBS video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner)
1 Rear-view camera CVBS video-input
Automatic switching to rear-view camera input on engagement of reverse gear
Activatable parking guide lines for the rear-view camera (not available on all
vehicles)
Video-in-motion in drive mode (ONLY for connected video-sources)
Video-inputs PAL and NTSC compatible
Version 16.03.2020 HW: CAM(V97)/(V30) CI-RL3-R40
Page2
Contents
1. Prior to installation
1.1. Delivery contents
1.2. Checking the compatibility of vehicle and accessories
1.3. Connection Video-Interface
1.4. Settings of the 8 Dip switches (black)
1.4.1. Enabling the interface’s video inputs (dip 2-3)
1.4.2. Rear-view camera setting (dip 5)
1.5. Settings of the 4 Dip switches (CAN function –red)
2. Installation
2.1. Place of installation
2.1.1. Place of installation –video interface
2.1.2. Place of installation –daughter PCB
2.2. Connection schema
2.3. Connection to the head-unit
2.3.1. Installation of the Exchange –retaining plate and the daughter PCB
2.3.2. Connecting ribbon cables
2.3.2.1. Ribbon cable –66pin
2.3.2.2. Warning notes, concerning the installation of ribbon cables
2.4. Connection from monitor to the video interface
2.5. Connection to the head-unit –Power / CAN
2.6. Connecting video sources
2.6.1. Video-sources to Video IN1 and Video IN2
2.6.2. Audio-insertion
2.6.3. After-market rear-view camera
2.6.3.1. Case 1: Video-interface receives the reverse gear signal
2.6.3.2. Case 2: Video interface does not receive the reverse gear signal
2.6.3.3. Video signal connection for the rear-view camera
2.7. Connecting video-interface and external keypad
2.8. Picture settings and guide lines
3. Interface operation
3.1. By CALL OFF button
3.2. By keypad
4. Specifications
5. FAQ –Trouble shooting
Version 16.03.2020 HW: CAM(V97)/(V30) CI-RL3-R40
Page3
Legal Information
By law, watching moving pictures while driving is prohibited, the driver must not be
distracted. We do not accept any liability for material damage or personal injury resulting,
directly or indirectly, from installation or operation of this product. Apart from using this
product in an unmoved vehicle, it should only be used to display fixed menus or rear-view-
camera video when the vehicle is moving (for example the MP3 menu for DVD upgrades).
Changes/updates of the vehicle’s software can cause malfunctions of the interface. Up to
one year after purchase we offer free software-updates for our interfaces. To receive a free
update, the interface has to be sent in at own cost. Wages for de-and reinstallation and
other expenditures involved with the software-updates will not be refunded.
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The
place of installation must be free of moisture and away from heat sources.
1.1. Delivery contents
Take down the serial number of the interface and store this manual for support
purposes: ____________________
Version 16.03.2020 HW: CAM(V97)/(V30) CI-RL3-R40
Page4
Compatibility
Limitations
Video only The interface inserts ONLY video signals into the infotainment.
For audio inserting, use the possibly existing factory audio-AUX-input
or a FM-modulator. If 2 AV-sources shall be connected to the
infotainment, for audio switching an additional electronic part is
required.
Factory rear-view camera Automatic switching-back from inserted video to factory rear-view
camera is only possible while the reverse gear is engaged. To delay
the switch-back, an additional electronic part is required.
1.2. Checking the compatibility of vehicle and accessories
Brand
Compatible vehicles
Infotainment systems
Opel
Adam
Corsa E
Crossland X since model year 2017 (no GM-LAN)
Grandland X since model year 2017 (no GM-LAN)
Mokka X since model year 2016-
Zafira C since model year 2017
R4.0 IntelliLink - 7" monitor
with DIN-cage attached
Version 16.03.2020 HW: CAM(V97)/(V30) CI-RL3-R40
Page5
1.3. Connection Video-Interface
The video-interface converts the connected after-market sources video signals into an digital
RGB signal which is inserted in the factory monitor using separate trigger options and it
reads vehicle’s digital signals out of the vehicle’s CAN-bus and converts them for the video
interface.
1.4. Settings of the 8 Dip switches (black)
Some settings have to be selected by the 8 dip-switches at the
video-interface. Dip position down is ON and position up is OFF.
See the following chapters for detailed information.
After each Dip-switch-change a power-reset of the Can-box has to be performed!
Dip
Function
ON (down)
OFF (up)
1
No function
Set to OFF
2
CVBS AV1-input
enabled
disabled
3
CVBS AV2-input
enabled
disabled
4
No function
set to OFF
5
Rear-view cam type
after-market
factory or none
6
No function
set to OFF
7
No function
set to OFF
8
No function
set to OFF
Version 16.03.2020 HW: CAM(V97)/(V30) CI-RL3-R40
Page6
1.4.1. Enabling the interface’s video inputs (dip 2-3)
Only the enabled video inputs can be accessed when switching through the interface’s video
sources. It`s recommended to enable only the required inputs for the disabled will be
skipped when switching through the video-interfaces inputs.
1.4.2. Rear-view camera setting (dip 5)
If set to OFF, the interface switches to factory LVDS picture while the reverse gear is engaged
to display factory rear-view camera or factory optical park system picture.
If set to ON, the interface switches to its rear-view camera input “Camera-IN” while the
reverse gear is engaged.
Note: Dip 1, 4, 6, 7 and 8 are out of function and have to be set to OFF.
1.5. Settings of the 4 Dip switches (CAN function - red)
Dip position down is ON and position up is OFF.
Navigation / Sy5tem
Dip 1
Dip 2
Dip 3
Dip 4
R4.0 IntelliLink systems
OFF
OFF
OFF
OFF
Set all 4 dips to OFF.
After each Dip-switch-change a power-reset of the Can-box has to be performed!
Version 16.03.2020 HW: CAM(V97)/(V30) CI-RL3-R40
Page7
2. Installation
Switch off the ignition and disconnect the vehicle’s battery! The interface needs a
permanent 12V source. If -according to factory rules- a disconnection of the battery has to
be avoided, it should be sufficient to use the vehicle’s sleep-mode. In case, the sleep-mode
doesn’t succeed, the battery has to be disconnected with a resistor lead.
The Interface needs a permanent power supply! If power isn’t directly taken from the
battery, the connection’s power has to be checked for being start-up proven and
permanent.
2.1. Place of installation
2.1.1. Place of installation –video-interface
The video-interface is performed to be installed at the backside of the head-unit.
2.1.2. Place of installation –daughter PCB
The daughter PCB is performed to be installed with an exchange housing plate behind the
head unit’s monitor panel.
Version 16.03.2020 HW: CAM(V97)/(V30) CI-RL3-R40
Page8
2.2. Connection schema
Version 16.03.2020 HW: CAM(V97)/(V30) CI-RL3-R40
Page9
2.3. Connections to the head-unit
2.3.1. Installation of the Exchange –retaining plate and the daughter PCB
Remove the head-unit and further remove the
original housing cover plate, which is fixed to the
head-unit housing by 5 Torx screws (T9).
Turn out the 4 screws of the monitor retaining
plate, after carefully unklipping the 66pin and
the 9pin ribbon cables.
Note: The connected ribbon cables have to be
handled with care to avoid each damage of the
sensitive electrical inducters (Refer also to
chapter “Connecting the ribbon cables”)
Remove the Original monitor retaining plate and replace it with the exchange
retaining-plate by using the original screws.
Version 16.03.2020 HW: CAM(V97)/(V30) CI-RL3-R40
Page10
After connecting the ribbon cables, the
daughter PCB has to be fixed with its
rearside at the exchange retaining plate
by using the enclosed 2 shorter screws.
Previous ribbon cable connection:
Read the following instructions!
2.3.2. Connecting the ribbon cables
2.3.2.1. Ribbon cable –66pin
Connect the daughter PCB’s pre-assembeled 66pin ribbon cable „IN PCB“ to the previously
become free ribbon cable base of the monitor mainboard (heed the following warning
notes!).
Table des matières
Autres manuels r.LiNK Système vidéo embarqué
r.LiNK
r.LiNK RL4-NAC08 Manuel utilisateur
r.LiNK
r.LiNK RL4-NAC Manuel utilisateur
r.LiNK
r.LiNK CI-RL4-C3D Manuel utilisateur
r.LiNK
r.LiNK RL4-UCON8-CP Manuel utilisateur
r.LiNK
r.LiNK RL3-SY3 Manuel utilisateur
r.LiNK
r.LiNK RL4-R40 Manuel utilisateur
r.LiNK
r.LiNK CI-RL3-MIB-4 Manuel utilisateur
r.LiNK
r.LiNK RL3-MIB92 Manuel utilisateur
r.LiNK
r.LiNK CI-RL5-UCON8-CP Manuel utilisateur
r.LiNK
r.LiNK RL2-UCON8-SM Manuel utilisateur
r.LiNK
r.LiNK 3008 NAC Manuel utilisateur
r.LiNK
r.LiNK RL3-MIB-4 Manuel utilisateur
r.LiNK
r.LiNK CI-RL4-MIB Manuel utilisateur
r.LiNK
r.LiNK RL4-MBN51 Manuel utilisateur
r.LiNK
r.LiNK 27-590 Manuel utilisateur
r.LiNK
r.LiNK RL3-MBN51 Manuel utilisateur
r.LiNK
r.LiNK CI-RL4-MIB-TR Manuel utilisateur
r.LiNK
r.LiNK CI-RL3-MIB92 Manuel utilisateur
