Quatech Asynchronous Communications Adapter for PCI bus... Manuel utilisateur
DSCLP/SSCLP-100
Two Channel Low Profile RS-232
Asynchronous Communications Adapter
for PCI bus
User's Manual
QUATECH, INC. TEL: (330) 655-9000
5675 Hudson Industrial Parkway FAX: (330) 655-9010
Hudson, Ohio 44236 http://www.quatech.com
1 DSCLP/SSCLP-100 User's Manual
WARRANTY INFORMATION
Quatech, Inc. warrants the DSCLP-100 or SSCLP-100 to be free of defects for
five (5) years from the date of purchase. Quatech, Inc. will repair or replace any board that
fails to perform under normal operating conditions and in accordance with the procedures
outlined in this document during the warranty period. Any damage that results from improper
installation, operation, or general misuse voids all warranty rights.
Please complete the following information and retain for your records. Have this
information available when requesting warranty service.
DATE OF PURCHASE:
MODEL NUMBER: DSCLP-100 or SSCLP-100
PRODUCT DESCRIPTION: Two or One Channel Low Profile RS-232
Asynchronous PCI Bus Communications Adapter
SERIAL NUMBER:
2006, Quatech, Inc.
NOTICE
The information contained in this document cannot be reproduced in any
form without the written consent of Quatech, Inc. Likewise, any software
programs that might accompany this document can be used only in accordance
with any license agreement(s) between the purchaser andQuatech, Inc. Quatech,
Inc. reserves the right to change this documentation or the product to which it
refers at any time and without notice.
The authors have taken due care in the preparation of this document and
every attempt has been made to ensure its accuracy and completeness. In no event
will Quatech, Inc. be liable for damages of any kind, incidental or consequential,
in regard to or arising out of the performance or form of the materials presented in
this document or any software programs that might accompany this document.
Quatech, Inc. encourages feedback about this document. Please send any
written comments to the Technical Support department at the address listed on the
cover page of this document.
DOS, Windows 95/98/2000/ME, Windows NT are trademarks or registered trademarks of
Microsoft Corporation. OS/2 is a registered trademark of IBM Corporation. All other trademarks
or registered trademarks are property of their respective owners.
3 DSCLP/SSCLP-100 User's Manual
Declaration of Conformity
Manufacturer's Name: Quatech Inc.
Manufacturer's Address: 5675 Huson Industrial Parkway
Akron, Ohio 44236 (USA)
Application of Council Directive: 89/336/EEC
Standards to which
Conformity is Declared: * EN50081-1 (EN55022,
EN60555-2, EN60555-3)
* EN50082-1 (IEC 801-2,
IEC 801-3, & IEC 801-4)
Type of Equipment: Information Technology
Equipment
Equipment Class: Commercial, Residential, & Light
Industrial
Product Name: PCI Two Port or One Port Serial
Communications Card
Model Number : DSCLP-100 / SSCLP-100
4 DSCLP/SSCLP-100 User's Manual
Table of Contents
39
10 Troubleshooting .................................
37
9 Specifications ......................................
36
8 PCI Resource Map ...............................
34
7 External Connections ............................
32
6.3.1 QTPCI.EXE ..................................... 31
6.3 DOS and other operating systems ................... 31
6.2 OS/2 ............................................... 31
6.1 Windows NT ....................................... 31
6 Other Operating Systems .......................
24
5.6.1 Changing Resource Settings with Device Manager .21
5.6 Viewing Resources with Device Manager ............ 20
5.5 Using the "New Hardware Found" Wizard .......... 20
5.4 Windows 95 ........................................ 19
5.3 Windows 98 ........................................ 18
5.2 Windows 2000 ...................................... 17
5.1 Windows Millennium ............................... 17
5 Windows Configurations ........................
16
4.4.2 Clock Rate Multiplier ............................ 15
4.4.1 Enhanced Serial Adapter Identification ........... 15
4.4 Options Register .................................... 14
4.3 Interrupt Status Register ............................ 14
4.2 Enabling the Special Registers ...................... 13
4.1 Base Address and Interrupt Level (IRQ) ............. 13
4 Address Map and Special Registers ...........
11
3 Hardware Installation ...........................
10
2.3 Force High-Speed UART Clock (X2 or X4, J4-J5) .... 9
2.2 Enable Scratchpad Register (SPAD, J2) .............. 9
2.1 Factory Default Configuration ....................... 9
2 Hardware Configuration .........................
8
1 General Information ..............................
5 DSCLP/SSCLP-100 User's Manual
1 General Information
The Quatech, Inc. DSCLP-100 (two-port) and SSCLP-100 (one-port)
provide RS-232 asynchronous serial communication interfaces for Low Profile
IBM-compatible personal computer systems using the PCI expansion bus. The
DSCLP-100 uses Quatech's new Enhanced Serial Adapter design. Legacy serial
port data rates are limited to a maximum of 115,200 bits per second. This manual
usually refers to the DSCLP-100. All information pertains equally to the
SSCLP-100, with the exception that with the SSCLP there is just one port instead
of two.As a PCI device, the DSCLP-100 requires no hardware configuration. The
card is automatically configured by the computer's BIOS or operating system.
The two serial ports share a single interrupt line and are addressed in a contiguous
block of 16 bytes. A special interrupt status register is provided to help software
to manage the shared interrupt.
The DSCLP-100's serial ports are implemented using 16550 Universal
Asynchronous Receiver/Transmitters (UARTs). These UARTs contain hardware
buffers (FIFOs) which reduce processing overhead and allow higher data rates to
be achieved.
The DSCLP-100 is supported under several popular operating systems and
environments. Contact the sales department for details on current software
offerings. Most device drivers are available for download from the Quatech world
wide web site at http://www.quatech.com.
6 DSCLP/SSCLP-100 User's Manual
2 Hardware Configuration
The DSCLP-100 is automatically configured at boot time by the
computer's BIOS or operating system. There are no required switches or jumpers
to set for installation.
This chapter lists a number of optional jumper settings that control various
hardware features. Jumpers J2, J4-J5 are grouped together at the end of the board
opposite the D-type connector (D-25 for DSCLP, D-9 for SSCLP). Any changes
from the factory default should be made before installing theDSCLP-100 in the
computer.
2.1 Factory Default Configuration
Figure 2 shows the jumper configuration as shipped from the factory, with
two spare jumpers applied in neutral positions. Remove one or both and apply as
shown in following sections to set optional features.
SPAD
X2
X4
J2
J4
J5
Figure 2 --- Factory default jumper configuration
2.2 Enable Scratchpad Register (SPAD, J2)
In the default configuration, an Interrupt Status Register(see section 4.3)
and an Options Register (see section 4.4) replace the scratchpad (base address + 7)
of each UART. If the SPAD jumper is applied as in Figure 3, the UART
scratchpad registers are enabled, and the Interrupt Status Register and the Options
Register are not available.
SPAD
X2
X4
J2
J4
J5
Figure 3 --- Enable scratchpad registers
7 DSCLP/SSCLP-100 User's Manual
2.3 Force High-Speed UART Clock (X2 or X4, J4-J5)
These jumpers force an increase of the UART input clock frequency by a
factor of two or four. This feature can allow legacy software to use baud rates
above 115,200 bits per second. It is also useful if the serial port device driver
does not directly support setting the higher baud rates through the Options
Register (see section 4.4).
If one of these jumpers is applied, it overrides any value written to the
Options Register to set the clock multiplier by software. The effective baud rate
will be either two or four times the value for which the UART itself is
programmed.
The factory default is none of these jumpers applied, which allows for
software control of the clock multiplier via the Options Register. The Options
Register powerup default is for a standard times-1 clock of 1.8432 MHz for
compatibility with standard serial ports.
SPAD
X2
X4
J2
J4
J5
Force times-two clock
Baud rates u
p
to 230.4 kb
p
s
SPAD
X2
X4
J2
J4
J5
Factory default
software control
SPAD
X2
X4
J2
J4
J5
Force times-four clock
Baud rates u
p
to 460.8 kb
p
s
Figure 4 --- Clock multiplier jumper options
8 DSCLP/SSCLP-100 User's Manual
3 Hardware Installation
1. Turn off the power of the computer system in which the DSCLP-100 is to
be installed.
2. Remove the system cover according to the instructions provided by the
computer manufacturer.
3. Make any desired optional jumper setting changes.
4. Install the DSCLP-100 in any empty PCI expansion slot. The board
should be secured by installing the Option Retaining Bracket (ORB)
screw.
5. Replace the system cover according to the instructions provided by the
computer manufacturer.
6. Attach and secure the cable connectors to the desired equipment.
7. Turn on the power of the computer system.
The output of the DSCLP-100 is a 25-pin D-connector. A cable is
provided to convert the D-25 into two standard male D-9 connectors with all
control signals provided to each port (RTS, DTR, CTS, DSR, DCD, and RI).
The output of the SSCLP-100 is one standard male D-9 connector.
J2
J4
J5 X2
X4
SPAD
Clock multiplier/
scratchpad select
Figure 5 --- Jumper/connector locations
9 DSCLP/SSCLP-100 User's Manual
4 Address Map and Special Registers
This chapter explains how the two UARTs and special registers are
addressed, as well as the layout of those registers. This material will be of interest
to programmers writing driver software for the DSCLP-100.
4.1 Base Address and Interrupt Level (IRQ)
The base address and IRQ used by the DSCLP-100 are determined by the
BIOS or operating system. Each serial port uses 8 consecutive I/O locations. The
two ports reside in a single block of I/O space in eight byte increments, for a total
of 16 contiguous bytes, as shown in Figure 6.
Base Address + 8 to Base Address + 15Serial 2
Base Address + 0 to Base Address + 7Serial 1
I/O Address RangePort
Figure 6 --- Port Address Map
All serial ports share the same IRQ. The DSCLP-100 signals a hardware
interrupt when any port requires service. The interrupt signal is maintained until
no port requires service. Interrupts are level-sensitive on thePCI bus.
The base address and IRQ are automatically detected by the device drivers
Quatech supplies for various operating systems. For cases where no device driver
is available, such as for operation under DOS, Quatech supplies the "QTPCI"
DOS software utility for manually determining the resources used. Seesection
6.3.1 for details.
10 DSCLP/SSCLP-100 User's Manual
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Quatech Adaptateur
Quatech
Quatech RS-485 Manuel utilisateur
Quatech
Quatech PCD-X/U132-E Manuel utilisateur
Quatech
Quatech PCD-B/PCI-E Manuel utilisateur
Quatech
Quatech ABDG-ET-DP501 Manuel utilisateur
Quatech
Quatech DSC-100 Manuel utilisateur
Quatech
Quatech SS-BLT-100 Manuel utilisateur
Quatech
Quatech MPAP-200 Manuel utilisateur
Quatech
Quatech QSC(LP)-100 Manuel utilisateur
Quatech
Quatech DSP-100 Manuel utilisateur
Quatech
Quatech DSCLP-200 Manuel utilisateur
Quatech
Quatech SS-BLT-100 Manuel utilisateur
Quatech
Quatech SS-BLT-100 Manuel utilisateur
Quatech
Quatech PCD-X/U142-E Manuel utilisateur
Quatech
Quatech DSU2-100 Manuel utilisateur
Quatech
Quatech MPAC-100 Manuel utilisateur
Quatech
Quatech RS-232 Manuel utilisateur
Quatech
Quatech DS-200 Manuel utilisateur
Quatech
Quatech DSU-200 Manuel utilisateur
Quatech
Quatech MPAP-100 Manuel utilisateur
Quatech
Quatech DSC-100 Manuel utilisateur
