Quadratec 12057.0261 Manuel utilisateur

The Trusted Source

Quadratec®Aluminum

Front Bumpers

Installation Manual for ’18 - Current Wrangler J Vehicles

#12057.0261 and 12057.0620

Full Width

Full Width Bum er

Narrow Bum er

TO REDUCE RISK OF SERIOUS INJURY OR PROPERTY DAMAGE:

READ A SAFETY MESSAGES AND UNDERSTAND A

INSTRUCTIONS AND PROCEDURE NOTICES BEFORE

ATTEMPTING TO INSTA OR USE THIS PRODUCT.

MOUNT WINCH USING ON Y APPROVED MOUNTING P ATE.

BUMPER/WINCH P ATE NOT INTENDED FOR WINCHES IN EX-

CESS OF 10000 BS. OAD IMITS FOR YOUR BUMPER/WINCH

MAY BE ESS DEPENDING ON CONDITION OF YOUR VEHIC E

AND ATTACHMENTS. FO OW A INSTRUCTIONS, IMITATIONS

& WARNINGS WITH YOUR VEHIC E, THIS PRODUCT, YOUR

WINCH AND SAFE WINCHING PRACTICES SUPP EMENT.

RISK OF EYE INJURY! SAFETY G ASSES MUST BE WORN AT

A TIMES WHI E INSTA ING OR MAINTAINING THIS PRODUCT.

TORQUE AND RECHECK FASTENERS AFTER 250 MI ES AND

FREQUENT Y THEREAFTER. INSPECT BUMPER, WINCH AND

MOUNT BEFORE USE. DO NOT USE IF DAMAGED.

CHECK STATE AND OCA HIGHWAY SAFETY AWS REGARDING

PERMITTED BUMPER TYPES AND HEIGHTS.

Q_ALUM_FBMPR_12057_0261_A4.qxp_A4 6/25/19 1:45 PM Page 1

The Trusted Source

READ A SAFETY MESSAGES AND A WAYS WEAR

SAFETY G ASSES WHEN WORKING WITH TOO S.

a hazardous situation which, if not avoided, could result in death or

serious injury. You CAN be KI ED or SERIOUS Y HURT if you don’t

follow instructions.

a hazardous situation which, if not avoided, could result in minor or

moderate injury. You CAN be moderately HURT and also may suffer

property damage if you don’t follow instructions.

Careful attention is required to this instruction or operation but does

generally not relate to personal injury. Damage to your Quadratec®

product or other property may result if you don’t follow instructions.

A Few Words About Product Safety:

Your Quadratec®Aluminum Front

Bumper is intended to enhance the util-

ity and enjoyment of your off road capa-

ble vehicle. Before installation, please

review the following safety information

and installation recommendations.

Throughout these instructions impor-

tant safety information is generally

preceded by one of three signal words

indicating the relative risk of injury,

property damage or adverse conse-

quence. The signal words mean:

Before You Begin Installation:

Congratulations on your purchase of

Quadratec®Aluminum Front Bumper for

your Jeep® Wrangler. This custom fit

front Bumper has been designed for

long life and a great look. Though con-

structed of only the finest materials, this

bumper must be maintained to keep its

look while performing under the tough-

est conditions. Please see page 10 for im-

portant care & maintenance tips to keep

your bumper looking like new. When

unpacking, check to make sure all parts

are included and not damaged due to

shipping. If any part is missing or

broken, please call Customer Service

at 800-745-6037 as soon as possible.

Thank you again for your purchase and

let’s start the installation process.

AS YOU UNPACK YOUR FRONT BUMPER, BE CAREFU NOT TO

SCRATCH THE FINISH WITH A KNIFE OR RAZOR. WE SUGGEST

P ACING THE UNPACKED BUMPER BACK INTO THE ORIGINA BOX

SO IT DOES NOT GET SCRATCHED BEFORE THE INSTA ATION BEGINS.

THIS BUMPER HAS A CUT-OUT FOR A VEHIC E RECOVERY WINCH.

THE BUMPER FEATURES AN INTEGRATED WINCH MOUNTING P ATE.

WE DED FRONT BUMPERS ARE HEAVY AND WE STRONG Y SUGGEST

THE ASSISTANCE OF AN AB E-BODIED ASSISTANT DURING IFTING

AND INSTA ATION OF YOUR BUMPER.

Q_ALUM_FBMPR_12057_0261_A4.qxp_A4 6/25/19 1:45 PM Page 2

The Trusted Source

THE MAJORITY OF THE INSTA ATION HAS TO DO WITH ADAPTING THE

ORIGINA EQUIPMENT FOG IGHTS AND WIRING TO THE NEW BUMPER.

THE PROCEDURE VARIES DEPENDING ON THE TRIM EVE OF YOUR J

CHASSIS WRANG ER (SPORT VS. SAHARA OR RUBICON).

PARTS LIST:

A) Aluminum Front Bumper w/Overrider QTY 1

B) 12 x 30mm Hex Bolts QTY 8

C) 12mm Flat Washers QTY 16

D) 12mm Nylock Nuts QTY 8

E) 10mm Hex Bolts QTY 2

F) 10x30 Button Head Allen Bolts QTY 16

G) 10mm Flat Washers QTY 24

H) 10mm Nylock Nuts QTY 6

I) 6x16 Hex Bolts QTY 4

J) 6mm Flat Washers QTY 4

K) 4x16 Socket Head Caps Screws QTY 8

L) 4mm Flat Washers QTY 16

) 4mm Nylock Nuts QTY 8

N) Spacer Plate Tabs QTY 4

REQUIRED TOOLS:

Safety Glasses

13, 16, & 18mm deep Sockets

19mm Socket

Extension & Ratchet

7mm & 5/16” Sockets & Rachet

7mm & 19mm Box End Wrenches

T-20 Torx Driver

3mm & 6mm Allen Hex Key Wrenches

Flat Blade Screwdrivers

Forked Clip/Trim Removal Tool

Torque Wrench (ft lbs)

A A

JLM

Quadratec Aluminum Front Bumper Parts & Tools:

Full-Width Bum erNarrow Bum er

Q_ALUM_FBMPR_12057_0261_A4.qxp_A4 6/25/19 1:45 PM Page 3

The Trusted Source

Aluminum J Front Bumper Installation Prep:

Put on safety glasses. Start by removing

the factory splash guard. Remove the 8

plastic push rivets on the underside of

the bumper. (FIG1)

Remove the two screws on the under-

side using a 5/16” socket. (FIG2) Re-

move the splash guard. Note: This will

not be reused with your new bumper.

Remove the two bolts holding on the

Original Equipment cross shield using a

16mm socket. Remove the cross shield

by lifting upward and out.

Note: This will not be reused with

your new bumper. (FIG3)

ocate the frame guard plastic retainers

on either side. (FIG4)

Remove the plastic retainers using

a small flat blade screwdriver. (FIG5)

FIG1 FIG2

FIG3

FIG4

FIG5

Q_ALUM_FBMPR_12057_0261_A4.qxp_A4 6/25/19 1:45 PM Page 4

The Trusted Source

Aluminum J Front Bumper Installation Prep:

Using a 18mm deep socket remove the

(8) bumper retaining nuts. There are 2

on the inside and outside of each frame

rail. (FIG6)

astly disconnect the fog light wiring

harness plug so the bumper can be

removed. (FIG7) Carefully remove the

bumper from the frame rails.

You will not be able to re-use your

original fog lamps. A set of “plastic

bumper” 10-18 JK or J Sahara and Ru-

bicon fog lamps will need to be sourced.

You will still need to re-use the fog lamp

wiring harness though.

For Wrangler Sport Model Vehicles:

ocate the 7 screws on either side hold-

ing the splash shields to bumper and

remove using a 7mm socket. (FIG8)

Disconnect the factory wiring harness

from the bumper mounted fog lights.

(FIG9)

ocate the 4 bolts holding the metal sub

structure to bumper fascia and remove

using a 13mm socket. (FIG10)

FIG6 FIG7

FIG8

FIG9

Foglight Harness Removal from Original Bumper (Sport Model)

FIG10

Q_ALUM_FBMPR_12057_0261_A4.qxp_A4 6/25/19 1:45 PM Page 5

The Trusted Source

ocate the (8) nuts holding the metal

sub structure to bumper fascia and

remove using a 13mm deep socket.

(FIGS 14A & 14B)

Now you will be able to access the fog

light wiring harness. Remove harness

using a trim removal tool and set aside

for re use. (FIG11)

FIG11

Foglight Harness Removal from Original Bumper (Sport Model)

Foglight Harness Removal from Original Bumper (Sahara & Rubicon Models)

ocate the (6) plastic fasteners on either

side holding the splash shields to

bumper and remove using a flat

blade screwdriver. (FIG12)

Disconnect the factory wiring harness

from the bumper mounted fog lights.

(FIG13)

FIG12

FIG13

FIG14A FIG14B

Q_ALUM_FBMPR_12057_0261_A4.qxp_A4 6/25/19 1:45 PM Page 6

The Trusted Source

Foglight Harness Removal from Original Bumper (Sahara & Rubicon Models)

Remove the two fog light wiring harness

retainers from metal sub structure using

a trim removal tool. (FIG15)

ocate the six plastic fasteners holding

the frame guard to bumper and remove

using a flat blade screwdriver. (FIG16)

FIG15 FIG16

ocate the (24) screws holding bumper

halves together and remove using a

7mm socket. (FIG17) Note: Several not

shown in this Figure.

Separate bumper halves and turn over

to access the fog light wiring harness.

Remove harness using a trim removal

tool set aside for re-use. (FIG18)

FIG17 FIG18

Finally, Remove the four screws

retaining the fog lamps to bumper fascia

using a 7mm socket and set aside for

re-use. (FIG19)

FIG19

Q_ALUM_FBMPR_12057_0261_A4.qxp_A4 6/25/19 1:45 PM Page 7

The Trusted Source

J Winch Mount Installation:

Remove the 4 bumper support brackets

using a 16mm socket and set hardware

aside for re-use later. (FIG 20)

oosely install the winch mount to

frame rails with the supplied M12 Bolt,

two washers per bolt and a locking nut

using a 19mm wrench & socket. (FIG 21)

oosely install the OEM hardware re-

moved in FIG 20 inside the frame rails

using spacer plates (if necessary) to

center winch mount best as possible.

(FIG 22)

oosely install the over rider support

bracket to the outside of frame rails

using the OEM hardware removed in

FIG 20. (FIG 23)

oosely secure the support brackets to

the winch mount using Two 10mm hex

head bolts, 4 washers and 2 nylock nuts.

(FIG 24)

Now tighten the 8 - 12mm bolts on front

of frame horns to 64ft lbs.

Next, tighten the OEM inner frame rail

bolts to 55ft lbs.

FIG20 FIG21

FIG22 FIG23

FIG24

Q_ALUM_FBMPR_12057_0261_A4.qxp_A4 6/25/19 1:45 PM Page 8

The Trusted Source

Fog ight Installation:

Aluminum Front Bumper: Install on Vehicle

Attach the fog lamps to the brackets as

shown with the supplied M4 hardware

using a 3mm hex key and 7mm wrench.

(FIGs 25A & B)

Secure the fog lamp brackets to the

winch plate with the supplied M6 bolts

and washers using a 10mm socket.

(FIG 26)

FIG25 FIG26

oosely secure the bumper to winch

plate with (2) M10 allen head bolts

using a 6mm hex key through the

fairlead mounting holes. (FIG 27)

Install the tow hooks through the

bumper and into the winch plate with

the supplied M10 allen head bolts and

washers using a 6mm hex key. (FIG 28)

You may now torque the over rider bar

bracket to winch plate M10 hardware

to 55ft lbs.

Now is a good time to install your winch

and fairlead into the bumper according

to your winch installation instructions.

FIG27 FIG28

With the help of a friend lift the bumper into place on the frame of the Jeep.

WE DED FRONT BUMPERS ARE HEAVY AND WE STRONG Y SUGGEST

THE ASSISTANCE OF AN AB E-BODIED ASSISTANT DURING IFTING

AND INSTA ATION OF YOUR BUMPER.

Q_ALUM_FBMPR_12057_0261_A4.qxp_A4 6/25/19 1:45 PM Page 9

The Trusted Source

QRC Front Bumper: Install on Vehicle

oosely install the over rider bar

through the bumper and into the sup-

port brackets with two M10 allen head

bolts and washers using a 6mm hex key.

(FIG 29)

astly, loosely install the final hardware

for the over rider bar using 4 M10 allen

head bolts, 8 washers and 4 nylock nuts

through the remaining holes. (FIG 30)

Final Adjustment:

You may now tighten the M10 allen head hardware through the tow hooks to 55ft

lbs. Torque the OEM hardware securing the over rider brackets to frame to 55ft lbs.

Now torque the remaining over rider bar M10 mounting hardware to 55ft lbs.

Installation is now complete.

FIG29 FIG30

Your Bumper has been designed and

manufactured to provide years of use.

However, like any product, general

maintenance is required to keep it

looking new.

Since the bumper is located on the front

of the vehicle, it is subject to potential

rock chips and other debris potentially

causing portions of the paint to chip off.

We recommend using a textured or gloss

black spray paint sprayed on a piece of

cardboard and Q-Tip to gently fill in

these chips. This will prevent any rust

from forming. On all bumpers there is a

chance of some surface rust showing

over time due to metal particles being

embedded in the paint. This surface rust

is easily removed by a non-abrasive

cleaner/ polish and a soft bristle brush

(not a metal brush!).

For bumpers with a textured finish,

wash only with soapy water and avoid

other waxes and polishes.

Bumper Care:

Q_ALUM_FBMPR_12057_0261_A4.qxp_A4 6/25/19 1:45 PM Page 10

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Quadratec Accessoires automobiles

Quadratec

Quadratec 12033.1000 Manuel utilisateur

Quadratec

Quadratec QuadraTop 11113.1135 Manuel utilisateur

Quadratec

Quadratec QuadraTop 11000.1135 Manuel utilisateur

Quadratec

Quadratec 92034.1007 Manuel utilisateur

Quadratec

Quadratec JL Manuel utilisateur

Quadratec

Quadratec 12057.014 Series Manuel utilisateur

Quadratec

Quadratec Lost Canyon ROVE-SEC-1 Manuel utilisateur

Quadratec

Quadratec 92034.1018 Manuel utilisateur

Quadratec

Quadratec Brute Strength 12057.0271 Manuel utilisateur

Quadratec

Quadratec 13111.0401 Guide rapide

Quadratec

Quadratec QuadraTop Adventure Top 1113.00 Series Manuel utilisateur

Quadratec

Quadratec QuadraTop 11113.2435 Manuel utilisateur

Quadratec

Quadratec Rock Sliders Manuel utilisateur

Quadratec

Quadratec EXPOSED RACKS Manuel utilisateur

Quadratec

Quadratec QuadraTop Adventure Top S Manuel utilisateur

Quadratec

Quadratec QRC Manuel utilisateur

Quadratec

Quadratec QRC Manuel utilisateur

Quadratec

Quadratec 12226.3011 Manuel utilisateur

Quadratec

Quadratec 12052.0904 Manuel utilisateur

Quadratec

Quadratec 506-Rock Manuel de l'opérateur

Quadratec

Quadratec 16053.5300 Manuel utilisateur

Quadratec

Quadratec 11081.02 Series Manuel utilisateur

Quadratec

Quadratec QuadraTop Adventure Top S With Flip Back... Manuel utilisateur

Quadratec

Quadratec 92034.1090 Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur