QKM AP3X Manuel utilisateur
is the trademark of QKM Technology (Dongguan) Co., Ltd. QKM has been granted ownership of this trademark.
User Manual
AP3X Robot
AP3X-1130-1653
AP3X-1130-1654
AP3X-1600-1653
AP3X-1600-1654
QKM Technology (Dongguan) Co., Ltd.
Document Version: V1.1.0
Issue Date: 01/11/2023
Preface
Document Version V1.1.0(01/11/2023) I
Preface
Thank you for purchasing the robot produced by QKM!
This manual describes the matters needing attention for proper use of the robot.
Read this manual carefully before using the robot.
Keep this manual properly for future reference.
Overview
This manual provides detailed information on product features, main components,
installation guide, system debugging and technical specifications of AP3X Robot so
that users can fully understand and properly use the robot.
Readers
This manual applies to:
System Engineer
Application Engineer
Installation Testing Engineer
Technical Support Engineer
Signs and their meanings
The signs in this document clearly indicate any dangers, warnings, attentions and
notes that may occur while users perform the operations described in this manual.
AP3X Robot User Manual
II Document Version V1.1.0 (01/11/2023)
Pay attention to the following signs when they appear in the document.
The signs in this manual are described in the table below:
Sign
Description
It indicates that a dangerous situation would occur and cause deaths
or serious injuries if it is not avoided.
It indicates that a potentially dangerous situation would occur and
cause personal injury or robot damage if it is not avoided.
It indicates that an unpredictable situation would occur and cause
robot damage, performance degradation, data loss, etc. if it is not
avoided.
It indicates the description of key information and tips of operation
skills.
Preface
Document Version V1.1.0(01/11/2023) III
Copyright© 2022 QKM Technology (Dongguan) Co., Ltd.
All Rights Reserved.
QKM Technology (Dongguan) Co., Ltd. (hereinafter referred to as QKM) owns the
patents, copyrights and other intellectual property rights of this product and its
software. Without the written authorization of QKM, any unit or individual shall not
extract or copy the contents of this document; and shall not directly or indirectly
reproduce, manufacture, process and use this product and related parts.
Trademark statement
is the trademark of QKM Technology (Dongguan) Co., Ltd. QKM has
been granted ownership of this trademark.
Disclaimer
QKM does not assume any direct, indirect, special, incidental or consequential loss or
liability due to improper use of this manual or this product.
The contents of this document are subject to change at any time due to product
upgrade or otherwise. QKM reserves the right to change the products or specifications
in this manual without prior notice. To know the latest information on the products
of QKM, please visit QKM's website and download it.
AP3X Robot User Manual
IV Document Version V1.1.0 (01/11/2023)
QKM Technology (Dongguan) Co., Ltd. (Headquarters)
Tower A, Building 17, Headquarters 1, No. 4 Xinzhu Road, Songshan Lake High-tech
Industrial Development Zone, Dongguan City, Guangdong Province
Tel: +86 0769-27231381
Fax: +86 0769-27231381-8053
Postcode: 523808
Email: service@qkmtech.com
Website: www.qkmtech.com
Version History
Document Version V1.1.0(01/11/2023) V
Version History
The version history contains the information on each update of the document,
and the latest version of the document includes the updates in all previous versions
of the document.
Version
Issue Date
Revision Content
V1.0.0
12/23/2021
The first version of the document was
released.
V1.0.1
06/01/2022
In subsection 7.7.2, add a description of
the robot motion speed.
V1.0.2
11/25/2022
Modify Table 4-7 MCP interface picture
Modify Figure 4-6 MCP wiring
V1.1.0
01/11/2023
Modify Chapter 7 Robot Operation：
1. Modify Section 7.1,add an overview of
the QRL language.
2. Modify the pictures of the ARM
installation process in Section 7.2.
AP3X Robot User Manual
VI Document Version V1.1.0 (01/11/2023)
3. Modify the interface picture and
operation steps of the new version of
ARM in Section 7.3.
4. Modify Section 7.4 Macro Command
Debugger Function Introduction and
Operation Procedures.
5. Added Section 7.5 QRL Mode
Description and Operation Content.
6. Modify the manual teaching interface
picture and operation steps in Section
7.6.
7. Modify Section 7.7 Servo power-up
pictures and content.
8. Modify the picture and content of the
robot speed adjustment control in
Section 7.8.
9. Added 7.10 Robot power-off method 1
and method 2 operation steps, and
added method 3.
Contents
Document Version V1.1.0(01/11/2023) VII
Contents
Preface.....................................................................................................................I
Version History .......................................................................................................V
Contents ...............................................................................................................VII
List of Figures ......................................................................................................XIII
List of Tables....................................................................................................... XIX
Chapter 1 Safety Precautions............................................................................1
1.1 PRECAUTIONS FOR GENERAL SAFETY ......................................................................1
1.2 PRECAUTIONS FOR SAFE USE ................................................................................3
1.3 MODEL IMPLICATION ...........................................................................................5
Chapter 2 Product Overview .............................................................................7
2.1 OVERALL INTRODUCTION .....................................................................................7
2.2 DIMENSION PARAMETERS .....................................................................................8
2.3 WORK SPACE ...................................................................................................10
2.4 ROBOT COORDINATE SYSTEM ..............................................................................12
2.5 PRODUCT FEATURES:........................................................................................13
Chapter 3 Main components...........................................................................14
3.1 BASE .............................................................................................................14
AP3X Robot User Manual
VIII Document Version V1.1.0 (01/11/2023)
3.2 MASTER ARM ...................................................................................................15
3.3 SLAVE ARM......................................................................................................16
3.4 MOVING PLATFORM...........................................................................................16
3.5 ROTATING SHAFT..............................................................................................18
3.6 DEFLECTOR.....................................................................................................19
3.7 TOP COVER FAN................................................................................................20
Chapter 4 Electrical Functions ........................................................................21
4.1 PANEL DESCRIPTION .........................................................................................21
4.2 INDICATOR DESCRIPTION....................................................................................23
4.3 DEFINITION OF PINS..........................................................................................25
4.3.1 Power interface ....................................................................................25
4.3.2 Definition of communication interfaces ..............................................25
4.3.3 Digital Input / Output interface(I/O) ....................................................26
4.3.4 Auxiliary encoder communication interface .......................................30
4.3.5 RS-232 communication interface.........................................................32
4.3.6 RS-485 communication interface.........................................................32
4.3.7 MCP communication interface.............................................................34
4.3.8 Ethernet interface (Ethernet) ...............................................................35
Chapter 5 Robot Installation ...........................................................................37
Table des matières
Autres manuels QKM Robotique
Manuels Robotique populaires d'autres marques
STEMCenter USA
STEMCenter USA Pi-Bot v2.00 Manuel utilisateur
SunFounder
SunFounder PiDog Manuel utilisateur
Universal Robots
Universal Robots UR5 Manuel utilisateur
Universal Robots
Universal Robots E Series Manuel utilisateur
YASKAWA
YASKAWA MOTOMAN-MPL80 II Manuel utilisateur
EFORT
EFORT ECR5 Manuel d'instructions
