QCI LS5T-37 Manuel utilisateur
FOR YOUR SAFETY
READ AND UNDERSTAND THE ENTIRE MANUAL
BEFORE OPERATING MACHINE
MODLE NUMBER : □LS5T-37 □LS5T-52
SERIALNUMBER:
Both model number and serial number may be found on the main label.
You should record both of them in a safe place for future use.
Save This Manual for Future Reference
5 TON LOG SPLITTER
Owner’s Manual
1
TABLE OF CONTENTS
CONTENTS PAGE
Safety Warnings & Cautions 2-4
Application Conditions 4
Specifications 5
Electrical Requirements 5
Contents of Shipping Container 5
Set up and Preparation for Operation 6, 7
Wiring Diagram 7
Plumbing Diagram 7
Log Splitter Operation 8, 9
Freeing a Jammed Log 9
Replacing Hydraulic Oil 10
Sharpening Wedge 10
Trouble Shooting 11
Parts Schematic (1) 12
Parts Schematic (2) 13
2
SAFETY WARNINGS & CAUTIONS
SYMBOL AFFIXED TO THE
MACHINE SAFETY WARNINGS & INSTRUCTIONS
UNDERSTAND YOUR LOG SPLITTER
Read and understand the owner’s manual and labels
affixed to the log splitter. Learn its application and
limitations as well as the specific potential hazards
peculiar to it.
INSPECT YOUR LOG SPLITTER
Check your log splitter before turning it on. Keep guards
in place and in working order. Form a habit of checking to
see that keys and adjusting wrenches are removed from
tool area before turning it on. Replace damaged, missing
or failed parts before using it.
AVOID DANGEROUS CONDITIONS
Put the log splitter on a 60 - 75cm high, stable, flat, and
level work bench where there is plenty of room for
handling, and help the operator stay alert. Bolt the log
splitter to the work surface if it tends to slip, walk, or
slide. Keep your work area clean and well lighted.
Cluttered areas invites injuries.
Do not use the log splitter in wet or damp areas or expose
it to rain. Do not use it in areas where fumes from paint,
solvents or flammable liquids pose a potential hazard.
DRUGS, ALCOHOL AND MEDICATION
Do not operate the log splitter while under the influence
of drugs, alcohol, or any medication that could affect your
ability to use it properly.
INSPECT YOUR LOG
Make sure there are no nails or foreign objects in logs to
be split. The ends of the logs must be cut square.
Branches must be cut of flush with the trunk
PROTECT YOUR EYES AND FACE
Any log splitter may throw foreign objects into the eyes.
This can cause permanent eye damage. Always wear
safety goggles. Everyday eyeglasses have only impact
3
resistant lenses. They are not safety glasses. Do not put
the log splitter on the ground for operations. This is
awkward operating position that the operator has to bring
his face close to the machine, and thus risks being struck
by wood chips or debris
EXTENSION CORDS
Improper use of extension cords may cause inefficient
operation of the log splitter which can result in
overheating. Be sure the extension cord is no longer than
10m and its section is no less than 2.5mm2to allow
sufficient current flow to the motor.
Avoid use of free and inadequately insulated connections.
Connections must be made with protected material
suitable for outdoor use.
AVOID ELECTRICAL SHOCK
Check that the electric circuit is adequately protected and
that it corresponds with the power, voltage and frequency
of the motor. Check that there is a ground connection,
and a regulation differential switch upstream.
Ground the log splitter. Prevent body contact with
grounded surfaces: pipes, radiators, ranges, and
refrigerator enclosures.
Never open the pushbutton box on the motor. Should this
be necessary, contact a qualified electrician.
Mark sure your fingers do not touch the plug’s metal
prongs when plugging or unplugging the log splitter.
KEEP VISITORS AND CHILDREN AWAY
The log splitter must be always operated by one person
only. Other people should keep a safe distance from the
work area, especially when the log splitter is under
operations. Never use another people to help you with
freeing jammed log.
DRESS PROPERLY
Do not wear loose clothing, gloves, neckties or jewelry
(rings, wrist watches). They can be caught in moving
parts.
Protective electrically non conductive gloves and non-skid
footwear are recommended when working. Wear
4
protective hair covering to contain long hair, preventing it
from get caught in machinery.
DON’T OVERREACH
Floor must not be slippery. Keep proper footing and
balance at all times. Never stand on log splitter. Serious
injury could occur if the tool is tipped or if the cutting
tools is unintentionally contacted. Do not store anything
above or near the log splitter where anyone might stand
on the tool to reach them.
AVOID INJURY FROM UNEXPECTED ACCIDENT
Always pay full attention to the movement of the log
pusher.
Do not attempt to load the log on until the log pusher has
stopped. Keep hands out of the way of all moving parts.
PROTECT YOUR HANDS
Keep you hands away from splits and cracks which open
in the log; They may close suddenly and crush or
amputate your hands. Do not remove jammed logs with
you hands.
DON’T FORCE TOOL
It will do a better and safer job at its design rate. Never
try to split logs larger than those indicated in the
specifications table. This could be dangerous and may
damage the machine.
Don’t use log splitter for a purpose for which it was not
intended.
NEVER LEAVE TOOL RUNNING UNATTENDED
Don’t leave tool until it has come to a complete stop.
DISCONNECT POWER
Unplug when not in use, before making adjustments,
changing parts, cleaning, or working on the log splitter;
Consult technical manual before servicing.
PROTECT THE ENVIRONMENT
Take used oil to an authorized collection point or follow
the stipulations in the country where the log splitter is
used.
Do not discharge into drains, soil or water.
5
MAINTAIN YOUR LOG SPLITTER WITH CARE
Keep the log splitter clean for best and safest
performance.
MAKE THE WORKSHOP CHILDPROOF
Lock the shop. Disconnect master switches. Store the log
splitter away from children and others not qualified to use
it.
6
APPLICATION CONDITIONS
This log splitter is a home use model. It is designed for operating under ambient
temperatures between +5oC and 40oC and for installation at altitudes no more
than 1000m above M.S.L. The surrounding humidity should less than 50% at 40oC.
It can be stored or transported under ambient temperatures between -25oC and
55oC.
SPECIFICATIONS
Model Number LS5T-37 LS5T-52
Motor 230V~ 50Hz 1500W IP54
Diameter * 5 ~ 25cm
Log Capacity Length 37cm 52cm
Splitting Force 5 t
Hydraulic Pressure 20Mpa
Hydraulic Oil Capacity 1.6 L 2.4L
Length 955mm 1200mm
Width 260mm
Overall Size
Height 485mm
Weight 45 kg 50 kg
* The diameter of the log is indicative – a small log can be difficult to split when it
has knobs or a particularly tough fiber. On the other hand, it may not be
difficult to split logs with regular fibers even if its diameter exceeds the max.
figure indicated above.
ELECTRICAL REQUIREMENTS
7
Connect the main leads to a standard 230V+10% (50Hz+1Hz) electrical supply
which has protection devices of under-voltage, over-voltage, over-current as well
as a residual current device (RCD) which maximum residual current rated at
0.03A.
CONTENTS OF THE SHIPPING CONTAINER
A. Log Splitter
B. Support Leg
C. Owner’s Manual
D. Loose Part Bag (containing)
M8 Bolts & Nuts
Note : Hardware to mount this log
spliter to a work bench is NOT
supplied.
1 set
1 pc
1 pc
5 sets
SET UP AND PREPARATION FOR OPERATION
1. Bolt the Support Leg to the Log Splitter, lift the log splitter by the handles at
both ends and place it on a 60 – 75cm high, stable, flat and level work surface.
2. Familiarize yourself with the controls and features of this log splitter in the
illustrations.
8
1. Oil Tank
2. Log Pusher
3. Work Table
4. Wedge
5. Lift Handle
6. Support Leg
7. Work Table Extension w/
Log Retaining Plates
8. Switch
9. Motor
10. Pushbutton Box
11. Wheels for Minor Moving
ONLY.
12. Lift Handle
13. Hydraulic Control Lever
14. Control Lever Guard
15. Bleed Screw
16. Oil Drain Bolt w/
Dipstick
Before operating the log splitter, the Bleed Screw should be loosened by some
rotations until air can go in and out of the oil tank smoothly. Air flow thru the
Bleed Screw hole should be detectable during the log splitter is under operations.
Before moving the log splitter, make sure the Bleed Screw is tightened to avoid oil
leaking from this point.
FAILED TO LOOSEN THE BLEED SCREW WILL KEEP THE SEALED AIR IN
HYDRAULIC SYSTEM BEING COMPRESSED AFTER BEING
DECOMPRESSED. SUCH CONTINUOUS AIR COMPRESSION AND
DECOMPRESSION WILL BLOW OUT THE SEALS OF THE HYDRAULIC SYSTEM AND
9
CAUSE PERMANT DAMAGE TO THE LOG SPLITTER.
17. Max Pressure Limiting Screw
DO NOT ADJUST THE MAX PRESSURE
LIMITING SCREW !
Max pressure was set before the log
splitter ex work and the max
pressure limiting screw is sealed with
glue to ensure the log splitter works
under pressure no more than 5 tons.
The setting was done by qualified
mechanics with professional
instruments.
Unauthorized resetting will cause the
hydraulic pump fail to output enough
splitting pressure or
RESULT IN
SERIOUS INJURY AS WELL AS DAMAGE
TO THE MACHINE .
WIRING DIAGRAM PLUMBING DIAGRAM
Ce manuel convient aux modèles suivants
1
Table des matières
Manuels fendeuse de bûches populaires d'autres marques
Scheppach
Scheppach OX 3-1000 Instructions de montage
Swisher
Swisher 21200 Manuel utilisateur
Elem Garden Technic
Elem Garden Technic FBHT65-22TCH Manuel utilisateur
Champion Power Equipment
Champion Power Equipment 90720 Manuel
Boss Industrial
Boss Industrial ES5T20 Manuel utilisateur
Villager
Villager LSP 12 T Manuel utilisateur
