pyroscience MU1 Manuel utilisateur
Micromanipulator MU1
Micromanipulator with motorized z-axis
USER MANUAL
www.pyroscience.com
MU1 | User Manual
© PyroScience GmbH 2
Micromanipulator MU1
Micromanipulator with motorized z-axis
Document Version 1.4
The MU1 is provided by:
PyroScience GmbH
Hubertusstrasse 35
52064 Aachen
Germany
Phone +49 (0)241 5183 2210
Fax +49 (0)241 5183 2299
Email info@pyroscience.com
Web www.pyroscience.com
Registered: Aachen HRB 17329, Germany
MU1 | User Manual
© PyroScience GmbH 3
TABLE OF CONTENT
1Introduction.....................................................................................................................................4
1.1 Packing List........................................................................................................................................4
1.2 Overview ............................................................................................................................................5
2Safety Guidelines............................................................................................................................6
3Installation and Operation ...........................................................................................................8
3.1 Mounting and Adjustment............................................................................................................8
3.2 Power Supply and Manual Motor Control..........................................................................11
3.3 Computer-Controlled Operation.............................................................................................13
4Maintenance ................................................................................................................................. 14
5Technical Specifications............................................................................................................. 16
MU1 | User Manual
© PyroScience GmbH 4
1INTRODUCTION
The Micromanipulator MU1 has been developed within the last decade in close
cooperation with leading scientists, who are specialized in microsensor measurements.
Please read carefully this manual before starting to use the device.
1.1 Packing List
Please check that all following items are included in your package:
•Main unit of the Micromanipulator MU1
•Power supply with exchangeable international plugs
•Data cable with adapter plug and USB connector
•Adapter for mounting of thin microsensors
Figure 1: Overview of the parts included in the package. Note that the exact appearance of
some delivered items might differ to this photograph.
MU1 | User Manual
© PyroScience GmbH 5
1.2 Overview
Figure 2: Overview of the micromanipulator MU1
The Micromanipulator MU1 has been developed for performing automized microprofile
measurements with microsensors. It consists of a compact manual micromanipulator for
the x-, y-, and z-axis, supplemented with a high-precision motorized slide (0.1 µm
resolution) for the z-axis. Versatile control software is provided by PyroScience as
freeware. If no computer is connected, the motorized slide can be operated by a control
knob integrated on top of the MU1 housing. For best operation conditions, the
micromanipulator MU1 should be mounted on the Heavy Stand HS1 from PyroScience.
Alternatively, it can be mounted on any flat surface providing a M6 mounting hole.
MU1 | User Manual
© PyroScience GmbH 6
2SAFETY GUIDELINES
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING TO WORK
WITH THIS DEVICE
•Before connecting the device to the mains voltage, please ensure that the operating
voltage stated on the power supply corresponds to the mains voltage.
•Ensure that the device is only operated under the climatic conditions specified in
the chapter "Technical Specifications" in this instruction manual.
•Maintenance, modifications and repair work must only be carried out by a suitable,
qualified technician, trained by PyroScience.
•If there is any reason to assume that the instrument can no longer be employed
without a risk (especially regarding any electrical parts), it must be set aside and
appropriately marked to prevent any further use.
•The safety of the user may be endangered, e.g. if the instrument a) is visibly
damaged, b) no longer operates as specified, c) has been stored under adverse
conditions for a longer period.
•If there is any problem, contact PyroScience and send the micromanipulator back
for repair.
•The user has to ensure the following laws and guidelines:
oEEC directives for protective labor legislation
oNational protective labor legislation
oSafety regulations for accident prevention
•This device is not protected against water spray
•This device is not water-proof
•This device must not be used under environmental conditions which cause water
condensation
•This device must not be opened
MU1 | User Manual
© PyroScience GmbH 7
THIS DEVICE MAY ONLY BE OPERATED BY QUALIFIED PERSONAL:
This device is only intended for use in the laboratory by qualified personal
according to this instruction manual and these safety guidelines!
Keep this device out of the reach of children!
Keep away from moving parts of the device!
This device is not intended for medical or military purposes!
MU1 | User Manual
© PyroScience GmbH 8
3Installation and Operation
PRECAUTION: The Micromanipulator MU1 comprises high-precision mechanics
which can easily be damaged by improper or harsh treatment. Handle with care!
3.1 Mounting and Adjustment
Please follow these steps for mounting the Micromanipulator MU1:
1. Release the tilting screws and open
the tilting mechanism. Screw the
mounting screw carefully into the
mounting nut of the Heavy Stand HS1 (if
the spring-loaded mounting nut is not
exactly centred within the groove, move
it back into position with your fingers).
2. Fasten the mounting screw.
MU1 | User Manual
© PyroScience GmbH 9
3. Fasten the tilting screws.
4. By releasing the tilting screws and the
mounting screw, the mounting angle and the
position of the micromanipulator can be
adjusted. Ensure to fasten the screws carefully,
if the desired position is reached.
5. Microsensors with diameters from 6.5 mm to
12 mm can be mounted directly to the sensor
mount.
MU1 | User Manual
© PyroScience GmbH 10
6. For mounting microsensors with diameters
from 0.5 mm up to 3 mm use the included
adapter for thin microsensors. The adapter can
hold two thin microsensors simultaneously.
PRECAUTION: The motor exerts considerable forces when moving. Keep any
parts of your body (especially fingers and hairs!) out of the mechanics!
Table des matières
