Purpleline fullstop SECURITY NEMESIS PRO Manuel utilisateur
INSTALLATION
GUIDE
REGISTERNOW
1YEAR
WARRANTY
PROPRO
WHEEL LOCK
PRODUCTCODE:FNPRO-100
WWW.PURPLELINEUSA.COM|925.215.7315
701 WILLOW PASS RD. STE 8, PITTSBURG, CA 94565
PARTS&FITTINGDIAGRAMS
1. Shield Plate
2. Wheel Bars
3. Lock Unit
4. Receiver Wheel Nuts (4)
5. Spacer Rings (x14)
6. Lock Unit Hex Screws
7. 3mm Hex Key
8. Key (x3)
9. Lock Cap
10. 19mm Wheel Wrench Adapter
11. Rim Shield
Your Saracen Pro comes with the below parts for installation:
WWW.PURPLELINEUSA.COM|925.215.7315
FIGURE A
FIGURE b FIGURE d
FIGURE c
FULLINSTALLATION
The FullStop® Nemesis Pro Wheel Lock is designed to secure the shield onto a replacement wheel nut so
that the Wheel Bars protrudes through one of the gaps in a wheel to prevent wheel rotation.
reciever wheel nut
Before the product can be used, one of your existing wheel nuts
must be removed and replaced with the Receiver Wheel Nut (4). This
replacement nut has been designed to fit the majority of trailer road
wheels, however, please check that your existing wheel nuts are of
the same specification.
The supplied Receiver Nuts (4) are 1/2”-20 and 9/16”-18. If in any doubt
consult the trailer manufacturer or wheel supplier BEFORE instal-
lation as it is possible to damage the hub of the trailer if the screw
threads do not match.
STEP 1
Once you have removed one of the wheel nuts, the Receiver Wheel Nut (4) can be fitted using the Wheel
Wrench Adapter (10) which enables you to use a standard 19mm wheel wrench (see Fig.B). The Receiver
Wheel Nut (4) should be tightened to the correct torque setting for your wheels.
NOTE: Check your Owners Manual for details or consult a qualified technician. Do not over-tighten or use an
impact wrench.
There are many possible combinations of how the
Nemesis Pro may fit to a particular wheel. Fig.C shows
that the Wheel Bars (2) are designed to slide in or out
as necessary depending on where the Receiver Nut
(4) has been installed in relation to which gap in the
wheel’s spokes.
NOTE: When installing the device the Wheel Bars (2)
should be located through the spokes and outside of
the wheel.
STEP 2
Before using the device it may be necessary to add Spacer Rings (5) to
ensure that, when fitted, the back face of the Shield Plate (1) is as tight
as possible to the face of the wheel when the Lock Unit (3) is locked
into the Receiver Nut (4).
To check this, first fit one of the keys into the Lock Unit (3) and rotate
it through 90° clockwise which releases the locking ball bearings. You
can now install the Lock Unit (3) through the aperture in the Shield
Plate (1) as shown in Fig. A.
Offer up the assembly to the Receiver Nut (4) and guide the end of
the Lock Unit (3) into the Receiver Nut (4) as far as it will go. Lock them
together by rotating the key anti-clockwise through 90° and remove
the key.
STEP 3
If the Shield Plate (1) is tight against the face of the wheel then no further adjustment is required. If,
however, there is a gap between the back face of the Shield Plate (1) and the face of the wheel then
Spacer Rings (5) must be used.
Try to gauge the amount of gap and add the necessary amount of Spacer Rings (5) between the Shield
Plate (1) and the Lock Unit (3) as shown in Fig.A.
If you add too many Spacer Rings (5) it will not be possible to fully engage the Lock Unit into the Receiver
nut and rotate the key to lock it. If this happens then simply remove one Spacer Ring at a time until you
achieve a secure fitment.
Once satisfied with the fit between the Shield Plate (1) and the face of the wheel, the Spacer Rings (5) can
be retained in place by securing the Lock Unit (3) to the Shield Plate (1) by tightening the Lock Unit Hex
Screw (6) using the supplied 3mm Hex Key (7).
The Nemesis Pro is now ready for use. Please check the
Receiver nut torque setting after the first 100 miles (approx)
and at regular intervals thereafter.
STEP 4
WWW.PURPLELINEUSA.COM|925.215.7315
MAINTENANCE
Fit protective Lock Cap (9) over shield plate (1) to help prevent ingress of dirt or water.
Grease the lock face and ball bearings before first use, with a light oil such as 3-IN-ONE or equivalent.
Thereafter spray any moving parts of the lock body with a light oil such as 3-IN-ONE or equivalent every
eight weeks.
Please store your keys in a safe place and remember to register your product.
Registration is quick and simple, go to www.purplelineusa.com
Please register within 14 days of purchase. Please retain your original purchase receipt.
DISCLAIMER
If used properly, your FullStop® product will be an effective deterrent. However, nothing can stop the efforts of the most
determined thief, and to this end no liability is accepted for any loss and/or damage caused by any illegal activity includ-
ing theft or vandalism. Liability also not accepted for any loss and/or damage arising from misuse, unauthorised repair
or alteration and failure to follow the user guide directions. No form of consequential loss what so ever will be accepted.
WWW.PURPLELINEUSA.COM|925.215.7315
701 WILLOW PASS RD. STE 8, PITTSBURG, CA 94565
NENESISPROUSERMANUAL-USA
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Purpleline Verrouillage
Purpleline
Purpleline FullStop Saracen Bradley FHL047 Manuel utilisateur
Purpleline
Purpleline FullStop Saracen Ultra Manuel utilisateur
Purpleline
Purpleline FullStop security Saracen Gullwing FHL555 Instructions de montage
Purpleline
Purpleline NEMESIS Instructions de montage
Purpleline
Purpleline fullstop Saracen FHL400 Manuel utilisateur
Purpleline
Purpleline FullStop FLL100 Manuel utilisateur
Purpleline
Purpleline FullStop Saracen Gullwing MP-031202 Instructions de montage
Purpleline
Purpleline FullStop Nemesis Plus Instructions de montage
Purpleline
Purpleline Fullstop Security Saracen FHL300-KA Manuel utilisateur
Purpleline
Purpleline SARACEN Instructions de montage
