pure cube CU580D Manuel utilisateur
CU580D/CU582D
Pure Cube Outdoor Sauna with Shower
Assembly Instructions
Tools Required
Carpenters Hammer
Cordless Drill
Hex Keys (Included)
Tape Measure
Step Ladder
Rubber Mallet
Level
Utility Knife
Hand Stapler (Optional)
Watch the assembly video on here
https://www.youtube.com/watch?v=K3haT6vqCHM&t=78s
05/2023
tel: 888-923-9813| info@leisurecraft.com|web: www.leisurecraft.com
Manufactured by:
Before you begin the installation of your Pure Cube Sauna, Please read these instructions completely.
Make sure the placement for your sauna is level and on a solid base.
Fig 2a
Fig 2b
*Always ensure that you have the correct screw length so that there will be enough thread to hold, and especially, so
that the screw does not go all the way through the material and come out the other side.
Parts Identification
The CU580D Pure Cube Sauna consists of 2 different sizes of wall panels that are available in either;
•Solid Cedar (privacy)
•Glass
•Wood/Glass (semi-privacy)
(2)- Glass panels Semi-privacy panel
(optional)
2
Fully Assembled
Glass Door
Privacy panels
(4) 33 ½” Large Panels
(1) 25 ¾” Small Panel
(1) 30” Shower Wall Panel
Louver Panels
(1)- 33 ½” Large Panel
(1) 25 ¾” Small Panel
(3) Roof Panels
(overhang on back)
Corner & Wall Trim
(4)-Corner Posts
(2)-Shower Corner Posts
CU580D/CU582D Pure Cube
Outdoor Sauna Assembly Instructions
tel: 888-923-9813| info@leisurecraft.com|web: www.leisurecraft.com
Manufactured by:
Fig 2a
Parts Identification (Cont..)
Floor Joists
(2)- Ends
(2)- Sides
(3)- Middle Joists
(13) Full Floor Boards
(1) Thinner Floor Board
Backrest
3
Bench Seats Bench Front Enclosures
Top
Bench
Bottom
Bench
(4)-Bench Brackets
2 ½” (63mm)
Finishing Nails
Hardware
2 ½” (63mm)
Wood Screws
2 ¾” (70mm)
Connector Bolts
2 ¾” (70mm)
Connector Lag Bolts
Threaded Cap
Nuts
EMPD Membrane
Premium Shower Hardware
(Hot & Cold)
(optional)
Economy Shower Hardware
(Cold only)
(optional)
Electric Heater & Guard
(optional)
Wood Stove
(optional)
tel: 888-923-9813| info@leisurecraft.com|web: www.leisurecraft.com
Manufactured by:
CU580D/CU582D Pure Cube
Outdoor Sauna Assembly Instructions
Fig 2a
Fig 2b
Organize the pieces of your Pure Cube outdoor sauna.
Start the assembly by laying out the floor supports.
4
Secure the corners of the floor supports together using
2 ½” (64mm) screws.
Repeat for all 4 corners.
Use a measuring tape to space out the floor joists evenly.
Once the floor joists are spaced out evenly, secure them
through the pre drilled pocket holes using
2” (51mm) screws.
tel: 888-923-9813| info@leisurecraft.com|web: www.leisurecraft.com
Manufactured by:
CU580D/CU582D Pure Cube
Outdoor Sauna Assembly Instructions
Fig 2a
Fig 2b
Gather your tongue and groove floor boards.
Insert the floor boards into the frame ensuring that they
are tight by tapping them together with a rubber mallet.
5
Fasten the floor boards into the floor joists and the inner
floor joists with 1 ½” (38mm) screws.
For aesthetic purposes, don’t secure the floor boards to
the first inner joist from the front of the sauna.
The benches will later cover the first 2 rows of screws.
Continue adding and securing the floor boards to the
floor joists.
tel: 888-923-9813| info@leisurecraft.com|web: www.leisurecraft.com
Manufactured by:
CU580D/CU582D Pure Cube
Outdoor Sauna Assembly Instructions
Fig 2a
Fig 2b
To start the assembly of the walls, bring in a 33 ½” solid
privacy panel and 1 corner post.
6
Line up the corner post to the back corner of the solid
privacy panel.
Secure the corner post to the panel using the provided
2 ¾” (70mm) Connector Lag Bolts.
* Note that the walls should be assembled so the screws and
bolts should be on the outside of the sauna.
Fasten a 33 ½” solid privacy panel to the corner post.
Fasten the panel and post together in the same manner
as the previous step.
tel: 888-923-9813| info@leisurecraft.com|web: www.leisurecraft.com
Manufactured by:
CU580D/CU582D Pure Cube
Outdoor Sauna Assembly Instructions
Fig 2a
Fig 2b
Attach a 25 ¾” panel to the larger side wall panel using
using the 2 ¾” (70mm) Connector bolt and nut through
the predrilled holes.
7
Secure the second 33 ½” solid privacy panel to the
previous back wall panel using 2 ¾” (70mm) Connector
bolt and nuts through the predrilled holes in the same
method as the previous step.
Attach a corner post to the back wall using the provided
2 ¾” (70mm) Connector Lag Bolts and then secure a
33 ½” solid wall panel to the post.
Bring in your glass panel to start the assembly of your
front wall.
*This will be either a full glass panel or semi privacy panel.
tel: 888-923-9813| info@leisurecraft.com|web: www.leisurecraft.com
Manufactured by:
CU580D/CU582D Pure Cube
Outdoor Sauna Assembly Instructions
Fig 2a
Fig 2b
Line the panel up flush to the post.
Secure the glass panel to the post using the provided
2 ¾” (70mm) Connector Lag Bolts.
8
Bring in the second glass panel and attach the panels
together using the 2 ¾” (70mm) Connector bolt and nut
through the pre drilled holes.
Attach a corner post to the glass panel in the same
method as previous steps.
Place the glass door flush to the corner post and wall
panel and secure with 2 ¾” (70mm) Connector Lag Bolts.
tel: 888-923-9813| info@leisurecraft.com|web: www.leisurecraft.com
Manufactured by:
CU580D/CU582D Pure Cube
Outdoor Sauna Assembly Instructions
Fig 2a
Fig 2b
Install the door handle by placing the provided 2”
(50mm) lag screws through the inner handle (short)into
the outer handle (longer)
Use the hex key to snug up, do not tighten all the way.
9
Ensure the outer handle lines up with the magnetic catch
on the door frame and then tighten the lag screws
completely.
Bring in the 30” wide shower wall panel and secure it to
the corner post using the provided 2 ¾” (70mm)
Connector Lag Bolts.
Attach a shower corner post to the wall panel with the
2 ¾” (70mm) Connector lag screws through the
predrilled holes.
tel: 888-923-9813| info@leisurecraft.com|web: www.leisurecraft.com
Manufactured by:
CU580D/CU582D Pure Cube
Outdoor Sauna Assembly Instructions
Fig 2a
Fig 2b
10
Line up the 33 ½” (large) louver panel to the shower post
using the 2 ¾” (70mm) Connector lag screws through the
predrilled holes.
Attach the smaller louver panel to the large panel using
the 2 ¾” (70mm) Connector bolt and nut through the
predrilled holes.
Attach the last shower corner post to the louver panel.
Using a tape measure, ensure that the walls stick out
1 ½” past the base of the sauna on the front and back
and both sides.
You can use a rubber mallet to tap into the correct place.
tel: 888-923-9813| info@leisurecraft.com|web: www.leisurecraft.com
Manufactured by:
CU580D/CU582D Pure Cube
Outdoor Sauna Assembly Instructions
Autres manuels pour CU580D
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels pure cube Produits de plomberie
pure cube
pure cube CU550 Manuel utilisateur
pure cube
pure cube CU570 Manuel utilisateur
pure cube
pure cube PU572 Manuel utilisateur
pure cube
pure cube CU550 Manuel utilisateur
pure cube
pure cube PU570 Manuel utilisateur
pure cube
pure cube CU580D Manuel utilisateur
pure cube
pure cube CU570 Manuel utilisateur
pure cube
pure cube CU580 Manuel utilisateur
