Pump Alarm Cellular Alarm Mode d’emploi
Quick Start Installation Guide
Copyright 2017, PumpAlarm.com, All Rights Reserved
Cellular Alarm
Please scan the image on the right with your
smartphone to view our installaon video, or
simply visit the link below.
www.pumpalarm.com/installaon
Need more guidance?
For technical support please call : 1-888-454-5051
Hours: M-F 8a-5p EST
The following items are available to you at pumpalarm.com:
• In Depth User Manual
• Installaon Video
• How it Works Video
• Online Store (where you can buy addional units and accessories)
PumpAlarm.com
203 W Morris St.
Indianapolis, IN 46225
888-454-5051
Components:
1. Cellular Alarm Unit
2. Hose Clamps (2)
3. Mounng Straps (4)
4. AA Baeries (4)
Oponal Sensors :
A. Water Sensor
B. Tilt Switch
C. Single Float Switch
D. Dual Float Switch
*See PumpAlarm.com for our
most up-to-date list of sensors.
Missing or Damaged Components?
Call PumpAlarm.com
888-454-5051
M-F 8:00a-5:00p EST
Do not return product to retail locaon.
1. 2.
3.
A. B. C. D.
4.
1. Status Light - Indicates the cellular status of your unit. Refer to the online manual
at pumpalarm.com for a descripon of the blink paerns.
2. Low Baery and Temperature Light - 2 red blinks indicates the backup baeries
are low. If the red light is ashing it indicates the baeries are crically low. When
the green light is ashing it indicates the Temperature Alarm. Refer to the online
manual at pumpalarm.com for a descripon of the blink paerns.
3. ON/OFF/MUTE - Press the buon 1 me to mute the device and 1 me to unmute
the device. Press and hold for 3 seconds to ON/OFF.
4. PUSH TO TEST - Press the buon 1 me to test device and receive a text message.
Hold the Test Buon to congure. Tap the Test Buon to test.
5. Input LEDs: 1 - 2 - LEDs blink when the associated inputs 1 and 2 are triggered.
6. Input LEDs: 3 - 4 - #3 input LED blinks when the lower oat is triggered and #4
blinks when the upper oat is triggered.
7. Sensor Input Connectors -
A. Inputs 1 and 2 are 2-pin, dry contact closure. Can be customized for
Normally Open or Normally Closed.
B. Inputs 3 and 4 are ed together as a 3-pin, for use with our dual oat and
sewage oat.
Geng to Know Your Device:
1
2
3
4
5
7A
67B
7
Unit Label
Mount the Cellular Alarm to a wall or pipe. Use mounng template below. It is the
correct dimensions for mounng the product. Mark the points using a pencil, then
use a 3/16” drill bit to make your holes. Apply the red anchors, and screws. Place
Cellular Alarm on the wall.
4.56”
xx
Mounng Template
Mounng Hardware and Sensors
Mount the device to a pipe using the mounng brackets (hose clamps).
Hose Clamps
Connect your choice of sensor into one of the inputs on the boom of the unit. We
recommend using the oat switch, or dual oat switch for sump pump applicaons
and the digital water sensor for oor or drain applicaons.
Please acvate your unit. Visit : www.pumpalarm.com/acvate.
Enter the 6 digit alphanumeric unit number found on the side of the unit. Then your
billing informaon.
This generates the phone number for your unit as well. Save this phone number as a
contact in your phone.
Install (4) AA baeries by opening the baery door on the back of the unit. Align the
negave (-) end of the baery to the spring in each holder.
Activate Online
www.pumpalarm.com/activate
PumpAlarm.com/activate
Phone #: (555)123-4567
add
photo
Cellular Alarm
Last
Company
Mobile
iPhone
(555)123-4567
Side of Unit
UNIT
ID 123ABC
1Unit Acvaon and Power On
AInstall Baeries
Plug the device into a 110V A/C outlet to power your unit on. Once the status light
turns solid green, press and hold the “Push to Test/Hold to Congure” buon for 3
seconds. Unit will chirp twice and status light will blink red & green. This will get the
unit ready to receive text messages from your cell phone. In the next step, you will
congure the unit by sending it text message commands.
Solid Green Light
BPower Device On
Caller ID and Conguraon Mode
If no phone numbers are configured in the unit, it will accept commands from any
phone number. Once a phone number is configured in the unit, only commands
from phone numbers configured in the unit will be processed.
The unit can be placed in Config Mode by pressing and holding the Mute button
until the status light (top light) changes to red/green blinking. This allows the device
to accept commands from any phone.
Using your mobile phone, create and send a text message to your device. Xis either
1,2, or 3for which phone number slot you would like to fill.
If you want text messages sent to addional phones, repeat this process. Your device
can hold up to three phone numbers.
phoneX [Phone Number]
Space
Adding phone numbers
Phone1 5557654321
2
A
Seng up Contact Phone Numbers
Adding phone numbers
Phone2 5557656778
For your main number, which
is phone1, you will send the
following message; replacing
5557654321 with your mobile
phone number.
Autres manuels pour Cellular Alarm
1
Table des matières
Autres manuels Pump Alarm Système de sécurité
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur