Pulsar PSC12015 Manuel utilisateur

PSC12015

PSC 12V/1,5A/66MM power supply

v.2.0

Edition: 10 from 11.09.2023

Supersedes edition: 9 from 26.03.2020

Features of the power supply:

power output 1,5 A/12 V DC *

universal supply voltage range ~100-240 V

high efficiency 87%

standby power <0,1 W

efficiency level: VI

IP67 case

protections:

SCP short-circuit protection

overvoltage protection (AC input)

overload (OLP)

warranty –2 year from the production date

1. Technical description.

1.1.General description.

Stabilized DC power supply is intended for supply CCTV cameras that require stabilised voltage of 12 V DC.

The unit is protected against short-circuit and overload.

1.2.Technical parameters.

Supply voltage

~100-240 V; 50/60 Hz

Current consumption

0,4 A

Supply power

18 W max.

Efficiency (average)

87%

Efficiency (10% load)

82%

Output voltage

12 V DC

Output current tAMB<30°C

1,5 A instantaneous current - refer to graph 1.

Output current tAMB=40°C

1 A - refer to graph 1.

Ripple voltage

100 mV p-p max.

Short-circuit protection SCP

electronic, automatic recovery

Overload protection OLP

105-150% of power supply, automatic recovery

IP protection class

IP67

Operation conditions

temperature 0oC ÷40oC

relative humidity 20%...90%

Dimensions (LxWxH)

58 x 58 x 28 [mm]

Net/gross weight

0,16 / 0,19 [kg]

Protection class EN 62368-1

II (second)

Lenght of DC cable

0,5 m + plug DC5,5/2,1 female

Lenght of AC cable

0,3 m

Storage temperature

-20ºC...+60ºC

* In order to extend the life of the power supply, the load current of 1 A is recommended.

Graph 1.

Relation between output current and ambient

temperature (instantaneous load).

Fig.1. Dimensions of power supply.

*Refer to graph 1

1.3. Accessories.

For the power supplies are available accessories - fuse blocks and cable adapter. For details –visit www.pulsar.pl.

2. Installation.

2.1. Requirements.

The power supply shall be mounted by a qualified installer, holding relevant permits and licenses (applicable and

required for a given country) with ~230 V mains supply. Unit should be mounted in confined spaces with normal relative

humidity (RH=90% maximum, without condensing) and temperature from 0°C to +40°C.

In order to fulfill LVD and EMC requirements the rules for power supplies, encasing and shielding shall be observed

according to application.

2.2. Installation procedure.

1. Fit the power supply inside the box or other device.

2. Connect the DC output to the load or to the terminal block.

3. Connect the power supply to the AC line.

4. After tests and operation control are performed, close installation box, case etc. and switch on the power.

3. Maintenance.

Any and all maintenance operations may be performed following the disconnection of the power supply from the power

network. The power supply does not require any specific maintenance procedures, however, in the case of significant level of

dust, it should be cleaned with the compressed air.

WEEE LABEL

Waste electrical and electronic equipment must not be disposed of with normal household waste.

According to European Union WEEE Directive, waste electrical and electronic equipment should

be disposed of separately from normal household waste.

Pulsar sp. j.

Siedlec 150,

32-744 Łapczyca, Poland

Tel. (+48) 14-610-19-45

e-mail: [email protected]

http:// www.pulsar.pl

Table des matières

Autres manuels Pulsar Alimentation

Pulsar

Pulsar PSAC 04244SEP Manuel utilisateur

Pulsar

Pulsar PSR12012 Manuel utilisateur

Pulsar

Pulsar PSDCR08128 Manuel utilisateur

Pulsar

Pulsar PSBEN 3024C Manuel utilisateur

Pulsar

Pulsar PSD15040 Manuel utilisateur

Pulsar

Pulsar PSBEN 3012C Manuel utilisateur

Pulsar

Pulsar SWS-150 Manuel utilisateur

Pulsar

Pulsar PSDC 04124 Manuel utilisateur

Pulsar

Pulsar MS 1012 Manuel utilisateur

Pulsar

Pulsar PSBS 5024C Manuel utilisateur

Pulsar

Pulsar PSBEN 10A12C/LCD Manuel utilisateur

Pulsar

Pulsar PSC12010 Manuel utilisateur

Pulsar

Pulsar PSDC Series Manuel utilisateur

Pulsar

Pulsar MS 2512 Manuel utilisateur

Pulsar

Pulsar HPSB 11A12C Manuel utilisateur

Pulsar

Pulsar PSCC10350 Manuel utilisateur

Pulsar

Pulsar PSD12080 Manuel utilisateur

Pulsar

Pulsar PSA12020 Manuel utilisateur

Pulsar

Pulsar ZBP 13,8V/2A Manuel utilisateur

Pulsar

Pulsar PSU-U-24V/AC-4A/4/FTA/PTC-TR-MC Manuel utilisateur

Pulsar

Pulsar HPSB 2512C Manuel utilisateur

Pulsar

Pulsar PSBD 10A12 Manuel utilisateur

Pulsar

Pulsar HADOC 2048B Manuel utilisateur

Pulsar

Pulsar POE1648C Manuel utilisateur

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur

Elmdene

Elmdene G1380xN-y-s Series Manuel utilisateur