PSL MicroPMU Manuel utilisateur

Power Sensors Ltd. 980 Atlantic Ave, Alameda CA 94501, USA

Tel ++1-510-522-4400 Fax ++1-510-522-4455 www.PowerSensorsLtd.com

MicroPMU Quick Start Kit

First Steps

Revision 13

Power Sensors Ltd. 980 Atlantic Ave, Alameda CA 94501, USA

Tel ++1-510-522-4400 Fax ++1-510-522-4455 www.PowerSensorsLtd.com

If the equipment is used in a manner not specified by the manufacturer, the protection provided by

the equipment may be impaired. Installation, service, and maintenance of your MicroPMU must

only be done by qualified personnel for electrical installations.

reproduced, or translated to another language without the prior written consent of Power Sensors

Ltd. “MicroPMU” is a registered trademark of Power Sensors Ltd. “Windows” “Excel”, and

“PowerPoint” are registered trademarks of Microsoft Corporation.

The information contained in this document is subject to change without notice.

PSL MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

USE.

PSL shall not be liable for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance, or use of this material. If you do not accept this

limitation on liability, please return the product to PSL prior to use.

Produced in the United States of America.

IMPORTANT: It is HIGHLY recommended that the Quickstart Kit (server, MicroPMUs, network

switch) is backed up by and uninterruptable power supply (UPS) in the event of a power surge or

failure. This will greatly reduce the likelihood of damage caused to any of the hardware or potential

data corruption as a result of a power outage or fluctuation. A recommended UPS model is the

APC-SMT750.

Document Release Date: March 2017

WARNING: Death, serious injury, or fire hazard could result from improper connection or

operation of the instruments of this kit. Carefully read and understand manual before connecting

this instrument.

AVERTISSEMENT: Si l'instrument est mal connecté, la mort, des blessures graves, ou un

danger d'incendie peuvent s'en suivre. Lisez attentivement le manuel avant de connecter

l'instrument.

WARNUNG: Der falsche Anschluß dieses Gerätes kann Tod, schwere Verletzungen oder Feuer

verursachen. Bevor Sie die Instrument von dieses Start Kit anschließen, müssen Sie die Anleitung

lesen und verstanden haben.

ADVERTENCIA: Una conexión incorrecta de los instrumentos de esta Start kit puede

producir la muerte, lesiones graves y riesgo de incendio. Lea y entienda el manual antes de

conectar.

Power Sensors Ltd. 980 Atlantic Ave, Alameda CA 94501, USA

Tel ++1-510-522-4400 Fax ++1-510-522-4455 www.PowerSensorsLtd.com

Table of Contents

1MicroPMU Quick Start Kit 4

1.1 What Is the MicroPMU Quick Start Kit?............................................................................ 4

1.2 Requirements prior to installation.................................................................................... 4

1.3 MicroPMU Quick Start Kit Contents ................................................................................. 5

2Connecting and setting up the MicroPMUs 6

2.1 MicroPMU Setup .............................................................................................................. 7

3Using the MicroPMU Plotter 10

3.1 Accessing the MicroPMU Plotter .................................................................................... 10

3.1.1 Client Connection via Windows 11

3.1.2 Client Connection via Mac OS 14

3.2 Plotter Header ................................................................................................................ 17

3.3 Selecting Streams............................................................................................................ 18

3.4 Setting the min and max range of the X-axis and Y-axis ................................................. 19

3.4.1 To set the X-axis 19

3.4.2 To set the Y-axis 21

3.5 Setting line color and labels for each data stream.......................................................... 22

3.6 Custom Axis Labels ......................................................................................................... 23

3.7 Y-axis Positions ............................................................................................................... 24

3.8 Export Tools .................................................................................................................... 25

4Troubleshooting 27

Power Sensors Ltd. 980 Atlantic Ave, Alameda CA 94501, USA

Tel ++1-510-522-4400 Fax ++1-510-522-4455 www.PowerSensorsLtd.com

1MicroPMU Quick Start Kit

1.1 What Is the MicroPMU Quick Start Kit?

Microsynchrophasors measurement is a new technology. It involves continuous monitoring and

recording of phenomena on the distribution or micro grids. The MicroPMU Plotting Application

software has been developed specifically to assist researchers and engineers to manage and

navigate through the large amount of measurements generated by the MicroPMU’s. The Quick

Start Kit serves as a convenient way to start a measurement campaign in just a few hours. It

includes instruments, cables, connectors, software and a basic communication infrastructure: all is

provided in a single pack to give you a head start!

1.2 Requirements prior to installation

IMPORTANT: It is HIGHLY recommended that the Quickstart Kit (server, MicroPMUs, network

switch) is backed up by and uninterruptable power supply (UPS) in the event of a power surge or

failure. This will greatly reduce the likelihood of damage caused to any of the hardware or potential

data corruption as a result of a power outage or fluctuation. A recommended UPS model is the

APC-SMT750.

The following is a list of requirements before installing any MicroPMUs.

Monitor with a VGA display port and a VGA cable

Google Chrome Browser (Windows, Linux, Mac OSX) or Safari (iOS and Mac OSX), or

Microsoft Internet Explorer (Windows)

Laptop with an Ethernet port and an Ethernet cable

Minimum 7 available power outlets

Power Sensors Ltd. 980 Atlantic Ave, Alameda CA 94501, USA

Tel ++1-510-522-4400 Fax ++1-510-522-4455 www.PowerSensorsLtd.com

1.3 MicroPMU Quick Start Kit Contents

Linux Server

1x Linux server (hosts the MicroPMU Plotter Application)

1x Power cord for Linux server

MicroPMUs

4x MicroPMU packages: each package includes a MicroPMU and its PM1, MS1, GPS1

and UPS1 modules

4x DIN rails

4x single phase voltage cables

4x current transformers

Networking

5x 10-meter Cat 5e patch cables (Ethernet)

1x 16 port 10/100 Desktop switch

The Quick Start Kit comes preconfigured as follows:

Server: 172.16.1.100

Subnet: 255.255.255.0

uPMU_1: 172.16.1.101

uPMU_2: 172.16.1.102

uPMU_3: 172.16.1.103

uPMU_4: 172.16.1.104

Power Sensors Ltd. 980 Atlantic Ave, Alameda CA 94501, USA

Tel ++1-510-522-4400 Fax ++1-510-522-4455 www.PowerSensorsLtd.com

2Connecting and setting up the MicroPMUs

The following top level diagram illustrates the entire physical setup and connections for the

Quickstart Kit.

Power Sensors Ltd. 980 Atlantic Ave, Alameda CA 94501, USA

Tel ++1-510-522-4400 Fax ++1-510-522-4455 www.PowerSensorsLtd.com

GPS1 Receiver/Antenna

MS1 Module

2.1 MicroPMU Setup

The MicroPMU, MS1, PM1 and UPS1 come preassembled on a DIN rail

Mount the GPS hardware

The GPS cable has an 8-pin terminal block on one end and an RJ-45 jack on the other end. The 8-pin

terminal block plugs into the MS1 module, the other end plugs into the GPS1 receiver.

IMPORTANT: Do not plug the RJ-45 end of the GPS cable into a network switch or router.

Place the GPS1 antenna/receiver in an area with direct line of sight to the

sky. For maximum exposure to satellites, mount it on the roof.

If necessary, the GPS cable can be extended using a standard RJ-45 coupler

and a standard CAT5, CAT5E, or CAT6 Ethernet cable (to a maximum length

of 500 feet / 150 meters).

Power Sensors Ltd. 980 Atlantic Ave, Alameda CA 94501, USA

Tel ++1-510-522-4400 Fax ++1-510-522-4455 www.PowerSensorsLtd.com

Connect the MicroPMU to the network switch

Plug in one of the provided Ethernet cables between the

MicroPMU and the provided 16-port Ethernet switch. Ethernet

status lights will turn on when connection is established.

Connect wires to mains AC terminals and PM1

Make sure the power is OFF before servicing these terminals.

When installing microPMUs in the field, connect the wires to the high voltage terminal block on the

MicroPMU. They will be labeled L1, L2, L3, N, and Ground.

The power cable comes pre-wired to two terminal blocks in the Quick Start Kit. Plug the larger

terminal block into the PQube 3 mains terminals and plug the smaller one into the power supply

input of the PM1 module.

IMPORTANT:You must ensure that the ground wire is connected to the MicroPMU. This is critical

for accurate phase angle measurements.

Power Sensors Ltd. 980 Atlantic Ave, Alameda CA 94501, USA

Tel ++1-510-522-4400 Fax ++1-510-522-4455 www.PowerSensorsLtd.com

5. Connect the server to network and power

Once all of the MicroPMU units have been set up, use one of the provided Ethernet cables to

connect the Gb1 interface of the server to the provided 16 port Ethernet switch.

Then, connect the server to a suitable power supply and press the power button next to the

“Dell” icon on the top left corner of the front panel.

Power Sensors Ltd. 980 Atlantic Ave, Alameda CA 94501, USA

Tel ++1-510-522-4400 Fax ++1-510-522-4455 www.PowerSensorsLtd.com

3Using the MicroPMU Plotter

3.1 Accessing the MicroPMU Plotter

The Quick Start Kit server comes with a pre-installed data plotting web application, known as the

MicroPMU Multiple-Resolution Plotter. The MicroPMU Plotter can be accessed using an internet

browser and by typing the IP address of the Quick Start Kit server: http://172.16.1.100. This IP address

is pre-configured with the Quick Start Kit. If this needs to be changed, refer to the MicroPMU

Administrator Manual. In order to view the plotter from a client computer, the IP configuration of either

the WI-FI or Ethernet adapter must be changed so that the adapter is on the same network as the

Quickstart Server and microPMU units. Refer to the next two sections for instructions on the client

connection from either a Windows or Mac computer.

Autres manuels pour MicroPMU

Table des matières

Manuels Traceur populaires d'autres marques

MUTOH

MUTOH Kona 760 Manuel utilisateur

HP 7475a Manuel utilisateur

Vulcan-Hart

Vulcan-Hart FC-500VC Manuel utilisateur

Roland

Roland TrueVIS VG-640 Manuel du propriétaire

Furuno

Furuno RP-180 Manuel utilisateur

Roland

Roland VersaCamm SP-540V Manuel utilisateur

MIMAKI

MIMAKI CF2 Series Manuel utilisateur

Ioline

Ioline Summit Manuel utilisateur

Summa

Summa S CLASS Manuel utilisateur

Gerber Technology

Gerber Technology GERBERplotter MP Series Manuel utilisateur

Furuno

Furuno RP-17 Manuel utilisateur

HP 7470A Manuel utilisateur

SII

SII LP-1010 Manuel utilisateur

Great Computer

Great Computer JII-61 Manuel utilisateur

Roland

Roland VersaUv LEF - 12i Manuel utilisateur

Lectra

Lectra Alys 120 Manuel utilisateur

MUTOH

MUTOH Ultima SC-850D Manuel utilisateur

Skycut

Skycut D Series Manuel utilisateur